Can't run QRTP.

I’ve just installed QRTP from the downloaded iso to the FAT32 partition.

When trying to run it, I’ve seen following messages:


Neutrino technology inside!!!

…skipped…

Detected EIDE. Scanning for devices.
This can take up to 30 seconds…
simq_timer: building abort ccb
ata_start_ccb: func 10
ata_ccb_abort: calling ata_error
/.diskroot file for root not found on any filesystem.
Starting with safe mode
[4102] fs-pkg built: Sep 7 2000 16:00:23
Warning [/pkgs/base/safe-config/etc/system/package/packages] doesn’t
seem to exist
Can’t access package config file
Unable to access packages.

…and nothing else.
So what’s the poblem?

Oleg Iscenko <iscenko@online.ru> wrote:
: I’ve just installed QRTP from the downloaded iso to the FAT32 partition.

: When trying to run it, I’ve seen following messages:

: --------------------------------------------
: Neutrino technology inside!!!

: …skipped…

: Detected EIDE. Scanning for devices.
: This can take up to 30 seconds…
: simq_timer: building abort ccb
: ata_start_ccb: func 10
: ata_ccb_abort: calling ata_error
: /.diskroot file for root not found on any filesystem.
: Starting with safe mode
: [4102] fs-pkg built: Sep 7 2000 16:00:23
: Warning [/pkgs/base/safe-config/etc/system/package/packages] doesn’t
: seem to exist
: Can’t access package config file
: Unable to access packages.
: --------------------------------------------

: …and nothing else.
: So what’s the poblem?

Your using the dma eide driver on a machine that we do
not currently support dma operation on. Use the non-dma
boot image.

----- Original Message -----
From: Michael Shane <mshane@qnx.com>
Newsgroups: comp.os.qnx
Sent: Tuesday, October 10, 2000 5:55 PM
Subject: Re: Can’t run QRTP.


Your using the dma eide driver on a machine that we do
not currently support dma operation on. Use the non-dma
boot image.

Thank you for response. I’ve tried to use the non-dma boot image too, but no
result. I’ve seen the same messages except of:

simq_timer: building abort ccb
ata_start_ccb: func 10
ata_ccb_abort: calling ata_error

Any ideas?

I got the same error message on my Dell (Dimension XPS T800r, Intel 800mhz,
256MBram, 30GB, 32mbGeForce256,…) except for the:

: simq_timer: building abort ccb
: ata_start_ccb: func 10
: ata_ccb_abort: calling ata_error

I tried both RTP boot floppies, with no luck. What is the next step?
Do I have to change my HD to non-DMA?

Thanks.
R.


“Michael Shane” <mshane@qnx.com> wrote in message
news:8rv742$7m7$2@nntp.qnx.com

Oleg Iscenko <> iscenko@online.ru> > wrote:
: I’ve just installed QRTP from the downloaded iso to the FAT32 partition.

: When trying to run it, I’ve seen following messages:

: --------------------------------------------
: Neutrino technology inside!!!

: …skipped…

: Detected EIDE. Scanning for devices.
: This can take up to 30 seconds…
: simq_timer: building abort ccb
: ata_start_ccb: func 10
: ata_ccb_abort: calling ata_error
: /.diskroot file for root not found on any filesystem.
: Starting with safe mode
: [4102] fs-pkg built: Sep 7 2000 16:00:23
: Warning [/pkgs/base/safe-config/etc/system/package/packages] doesn’t
: seem to exist
: Can’t access package config file
: Unable to access packages.
: --------------------------------------------

: …and nothing else.
: So what’s the poblem?

Your using the dma eide driver on a machine that we do
not currently support dma operation on. Use the non-dma
boot image.