Here’s the output from pci -vvv, followed by the output from nettrap -vvv.
Thanks!
P.S. If there is a newsreader for QnX please let me know. I have to switch
back to win98 to post this.
rsm
Output from pci -vvv:
PCI version = 2.10
Class = Bridge (Host/PCI)
Vendor ID = 8086h, Intel Corporation
Device ID = 7190h, 82443BX/ZX 440BX/ZX AGPset Host Bridge
PCI index = 0h
Class Codes = 060000h
Revision ID = 2h
Bus number = 0
Device number = 0
Function num = 0
Status Reg = 2210h
Command Reg = 6h
I/O space access disabled
Memory space access enabled
Bus Master enabled
Special Cycle opertations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Capabilities Pointer = a0h
Capability ID = 2h
Capabilities = 10h - 1f000203h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 0c a8 00 ff 00 00 00 09 03 10 11 01 00 00 00 00
0x60: 08 10 10 10 10 10 10 10 00 0f c0 00 00 8a 00 00
0x70: 20 1f 0a 38 05 00 00 01 26 03 04 38 00 00 00 00
0x80: 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: d0 20 00 00 04 61 00 00 00 05 00 00 00 00 00 00
0xA0: 02 00 10 00 03 02 00 1f 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 30 00 00 00 00 00 00 00 20 10 00 00
0xC0: 00 00 00 00 ff ff ff ff 18 0c ff ff 61 00 00 00
0xD0: 08 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 4c ad ff bb 8a 3e 00 80 2c d3 f7 cf 9d 3e 00 00
0xF0: 40 01 00 00 00 f8 00 60 20 0f 00 00 00 00 00 00
Class = Bridge (PCI/PCI)
Vendor ID = 8086h, Intel Corporation
Device ID = 7191h, 82443BX/ZX 440BX/ZX AGPset PCI-to-PCI bridge
PCI index = 0h
Class Codes = 060400h
Revision ID = 2h
Bus number = 0
Device number = 1
Function num = 0
Status Reg = 220h
Command Reg = 107h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle opertations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents enabled
Header type = 1h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
Primary Bus Number = 0h
Secondary Bus Number = 1h
Subordinate Bus Number = 1h
Secondary Latency Timer = 40h
I/O Base = e0h
I/O Limit = e0h
Secondary Status = 22a0h
Memory Base = e400h
Memory Limit = e5f0h
Prefetchable Memory Base = e600h
Prefetchable Memory Limit= e6f0h
Prefetchable Base Upper 32 Bits = 0h
Prefetchable Limit Upper 32 Bits = 0h
I/O Base Upper 16 Bits = ffffh
I/O Limit Upper 16 Bits = ffffh
Bridge Control = 136ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 88 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Class = Bridge (PCI/ISA)
Vendor ID = 8086h, Intel Corporation
Device ID = 7110h, 82371AB PIIX4 ISA Bridge
PCI index = 0h
Class Codes = 060100h
Revision ID = 2h
Bus number = 0
Device number = 7
Function num = 0
Status Reg = 280h
Command Reg = fh
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle opertations monito
r
%09Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 65 00 30 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 0b 80 80 0a 10 00 00 00 00 f2 80 00 00 00 00 00
0x70: 00 00 00 00 00 00 0c 0c 00 00 00 00 00 00 00 00
0x80: 00 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 21 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
Class = Mass Storage (IDE)
Vendor ID = 8086h, Intel Corporation
Device ID = 7111h, 82371AB PIIX4 IDE Controller
PCI index = 0h
Class Codes = 010180h
Revision ID = 1h
Bus number = 0
Device number = 7
Function num = 1
Status Reg = 280h
Command Reg = 5h
I/O space access enabled
Memory space access disabled
Bus Master enabled
Special Cycle opertations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
IO Address = f000h length 16 enabled
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 07 a3 77 e3 90 00 00 00 05 00 02 02 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
Class = Serial Bus (Universal Serial Bus)
Vendor ID = 8086h, Intel Corporation
Device ID = 7112h, 82371AB PIIX4 USB Interface
PCI index = 0h
Class Codes = 0c0300h
Revision ID = 1h
Bus number = 0
Device number = 7
Function num = 2
Status Reg = 280h
Command Reg = 5h
I/O space access enabled
Memory space access disabled
Bus Master enabled
Special Cycle opertations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
IO Address = 6400h length 32 enabled
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = INT D
Interrupt line = 10
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
Class = Bridge (Unknown)
Vendor ID = 8086h, Intel Corporation
Device ID = 7113h, 82371AB PIIX4 Power Management Controller
PCI index = 0h
Class Codes = 068000h
Revision ID = 2h
Bus number = 0
Device number = 7
Function num = 3
Status Reg = 280h
Command Reg = 3h
I/O space access enabled
Memory space access enabled
Bus Master disabled
Special Cycle opertations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 01 61 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 58 1f 00 00 00 00 00 04 20 05 03 00 00 00 00
0x60: 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 01 5f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
Class = Network (Ethernet)
Vendor ID = 10d9h, Macronix International Co. Ltd.
Device ID = 531h, MX98715/725 Single Chip Fast Ethernet NIC Controller
PCI index = 0h
Class Codes = 020000h
Revision ID = 25h
Bus number = 0
Device number = 12
Function num = 0
Status Reg = 290h
Command Reg = 87h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle opertations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver enabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 8h un-cacheable
IO Address = 6800h length 256 enabled
Mem Address = e8000000h 32bit length 256 enabled
Subsystem Vendor ID = 2078h
Subsystem ID = 540h
Expansion ROM = e7000000h length 262144 disabled
Max Lat = 56ns
Min Gnt = 8ns
PCI Int Pin = INT A
Interrupt line = 11
Capabilities Pointer = 44h
Capability ID = 1h
Capabilities = f601h - 0h
Device Dependent Registers:
0x40: 00 00 00 00 01 00 01 f6 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Class = Display (VGA)
Vendor ID = 1002h, ATI Technologies
Device ID = 4742h, Rage 3D Pro AGP 2x
PCI index = 0h
Class Codes = 030000h
Revision ID = 5ch
Bus number = 1
Device number = 0
Function num = 0
Status Reg = 290h
Command Reg = 86h
I/O space access disabled
Memory space access enabled
Bus Master enabled
Special Cycle opertations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver enabled
Fast back-to-back transact
ions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 8h un-cacheable
Mem Address = e6000000h prefetchable 32bit length 16777216 enabled
IO Address = e000h length 256 disabled
Mem Address = e5000000h 32bit length 4096 enabled
Subsystem Vendor ID = 1002h
Subsystem ID = 40h
Expansion ROM = e4000000h length 131072 disabled
Max Lat = 0ns
Min Gnt = 8ns
PCI Int Pin = INT A
Interrupt line = 11
Capabilities Pointer = 50h
Capability ID = 2h
Capabilities = 10h - ff000203h
Device Dependent Registers:
0x40: 0c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 02 00 10 00 03 02 00 ff 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Output from nettrap -vvv:
Looking for a ne1000/2000 ethernet card’s boot rom …
About to sniff memory at C800 for a QNX boot rom …
About to sniff memory at CC00 for a QNX boot rom …
About to sniff memory at D000 for a QNX boot rom …
About to sniff memory at D400 for a QNX boot rom …
Looking for a ne1000/2000 ethernet card’s I/O port …
About to read I/O port 21F …
About to write to I/O port 21F …
About to read I/O port 21F …
About to write to I/O port 21F …
About to read I/O port 200 …
CR = F0 …
About to read I/O port 23F …
About to write to I/O port 23F …
About to read I/O port 23F …
About to write to I/O port 23F …
About to read I/O port 220 …
CR = 00 …
About to read I/O port 25F …
About to write to I/O port 25F …
About to read I/O port 25F …
About to write to I/O port 25F …
About to read I/O port 240 …
CR = FF …
About to read I/O port 27F …
About to write to I/O port 27F …
About to read I/O port 27F …
About to write to I/O port 27F …
About to read I/O port 260 …
CR = FF …
About to read I/O port 29F …
About to write to I/O port 29F …
About to read I/O port 29F …
About to write to I/O port 29F …
About to read I/O port 280 …
CR = FF …
About to read I/O port 2BF …
About to write to I/O port 2BF …
About to read I/O port 2BF …
About to write to I/O port 2BF …
About to read I/O port 2A0 …
CR = FF …
About to read I/O port 2DF …
About to write to I/O port 2DF …
About to read I/O port 2DF …
About to write to I/O port 2DF …
About to read I/O port 2C0 …
CR = FF …
About to read I/O port 2FF …
About to write to I/O port 2FF …
About to read I/O port 2FF …
About to write to I/O port 2FF …
About to read I/O port 2E0 …
CR = FF …
About to read I/O port 31F …
About to write to I/O port 31F …
About to read I/O port 31F …
About to write to I/O port 31F …
About to read I/O port 300 …
CR = FF …
About to read I/O port 33F …
About to write to I/O port 33F …
About to read I/O port 33F …
About to write to I/O port 33F …
About to read I/O port 320 …
CR = FF …
About to read I/O port 35F …
About to write to I/O port 35F …
About to read I/O port 35F …
About to write to I/O port 35F …
About to read I/O port 340 …
CR = FF …
About to read I/O port 37F …
About to write to I/O port 37F …
About to read I/O port 37F …
About to write to I/O port 37F …
About to read I/O port 360 …
CR = FF …
About to read I/O port 39F …
About to write to I/O port 39F …
About to read I/O port 39F …
About to write to I/O port 39F …
About to read I/O port 380 …
CR = FF …
About to read I/O port 3BF …
About to write
to I/O port 3BF …
About to read I/O port 3BF …
About to write to I/O port 3BF …
About to read I/O port 3A0 …
CR = FF …
About to read I/O port 3DF …
About to write to I/O port 3DF …
About to read I/O port 3DF …
About to write to I/O port 3DF …
About to read I/O port 3C0 …
CR = FF …
About to read I/O port 3FF …
About to write to I/O port 3FF …
About to read I/O port 3FF …
About to write to I/O port 3FF …
About to read I/O port 3E0 …
CR = FF …
Looking for a ne1000/2000 pci ethernet card …
Looking for a AHA4-compatible scsi card (don’t ask why) …
About to read I/O port 130 …
About to read I/O port 134 …
About to read I/O port 230 …
About to read I/O port 234 …
About to read I/O port 330 …
About to read I/O port 334 …
Looking for a WD/SMC 8003/8013/elite/ultra ethernet card …
About to read I/O ports 208 209 20A …
About to read I/O ports 228 229 22A …
About to read I/O ports 248 249 24A …
About to read I/O ports 268 269 26A …
About to read I/O ports 288 289 28A …
About to read I/O ports 2A8 2A9 2AA …
About to read I/O ports 2C8 2C9 2CA …
About to read I/O ports 2E8 2E9 2EA …
About to read I/O ports 308 309 30A …
About to read I/O ports 328 329 32A …
About to read I/O ports 348 349 34A …
About to read I/O ports 368 369 36A …
About to read I/O ports 388 389 38A …
Looking for a 3Com 509/Etherlink III ethernet card …
About to write [many times] to I/O port 100 …
About to read from and write [many times] to I/O port 100 …
Manufacturer ID in eeprom incorrect!
Looking for a ne2100 ethernet card …
About to read 16-bit I/O port 314 …
About to write to 16-bit I/O port 312 …
About to read 16-bit I/O port 310 …
About to write to 16-bit I/O port 312 …
About to read 16-bit I/O port 310 …
CSR 88 = FFFF, CSR 89 = FFFF
About to read 16-bit I/O port 334 …
About to write to 16-bit I/O port 332 …
About to read 16-bit I/O port 330 …
About to write to 16-bit I/O port 332 …
About to read 16-bit I/O port 330 …
CSR 88 = BFFE, CSR 89 = BFFE
About to read 16-bit I/O port 354 …
About to write to 16-bit I/O port 352 …
About to read 16-bit I/O port 350 …
About to write to 16-bit I/O port 352 …
About to read 16-bit I/O port 350 …
CSR 88 = FFFF, CSR 89 = FFFF
About to read 16-bit I/O port 374 …
About to write to 16-bit I/O port 372 …
About to read 16-bit I/O port 370 …
About to write to 16-bit I/O port 372 …
About to read 16-bit I/O port 370 …
CSR 88 = FFFF, CSR 89 = FFFF
pci_autodetect(): _CA_PCI_Find_Device(79c970/974, slot 0) failed
pci_autodetect(): _CA_PCI_Find_Device(79c970/974, slot 1) failed
pci_autodetect(): _CA_PCI_Find_Device(79c970/974, slot 2) failed
pci_autodetect(): _CA_PCI_Find_Device(79c970/974, slot 3) failed
Looking for 21x4x/LiteOn PNIC Ethernet Cards.
tulip_scan():_CA_PCI_Find_Device(0x0002, 0x1011, Slot 0, Chipset 21040),
Failed.
tulip_scan():_CA_PCI_Find_Device(0x0008, 0x1011, Slot 0, Chipset 21140),
Failed.
tulip_scan():_CA_PCI_Find_Device(0x0009, 0x1011, Slot 0, Chipset 21140),
Failed.
tulip_scan():_CA_PCI_Find_Device(0x0014, 0x1011, Slot 0, Chipset 21041),
Failed.
tulip_scan():_CA_PCI_Find_Device(0x0019, 0x1011, Slot 0, Chipset 21143),
Failed.
tulip_scan():_CA_PCI_Find_Device(0x0002, 0x11ad, Slot 0, Chipset 168), Failed.
tulip_scan():_CA_PCI_Find_Device(0x0168, 0x11ad, Slot 0, Chipset 168), Failed.
Looking for a SMC 91CXX ethernet chip …
About to read I/O port 28F …
About to read I/O port 2EF …
About to read I/O port 30F …
About to read I/O port 32F …
About to read I/O port 34F …
About to read I/O port 36F …
About to read I/O port 38F …
About to read I/O port 3AF …
Looking for a 82595 ethernet card%27s I/O port …
About to read I/O port 200 …
About to write I/O port 200 …
Register Bank switch failed …
About to read I/O port 220 …
About to read ID from I/O port 222 …
About to read I/O port 240 …
About to write I/O port 240 …
Register Bank switch failed …
About to read I/O port 260
…
About to write I/O port 260 …
Register Bank switch failed …
About to read I/O port 280 …
About to write I/O port 280 …
Register Bank switch failed …
About to read I/O port 2A0 …
About to write I/O port 2A0 …
Register Bank switch failed …
About to read I/O port 2C0 …
About to write I/O port 2C0 …
Register Bank switch failed …
About to read I/O port 2E0 …
About to write I/O port 2E0 …
Register Bank switch failed …
About to read I/O port 300 …
About to write I/O port 300 …
Register Bank switch failed …
About to read I/O port 320 …
About to write I/O port 320 …
Register Bank switch failed …
About to read I/O port 340 …
About to write I/O port 340 …
Register Bank switch failed …
About to read I/O port 360 …
About to write I/O port 360 …
Register Bank switch failed …
About to read I/O port 380 …
About to write I/O port 380 …
Register Bank switch failed …
About to read I/O port 3A0 …
About to write I/O port 3A0 …
Register Bank switch failed …
About to read I/O port 3C0 …
About to write I/O port 3C0 …
Register Bank switch failed …
About to read I/O port 3E0 …
About to write I/O port 3E0 …
Register Bank switch failed …
Looking for an Intel 82557/8 ethernet card …
Looking for an SMC9432 (Epic) ethernet card …
Looking for a Crystal 8900 ethernet card’s I/O port …
About to read I/O port 200 …
About to read I/O port 220 …
About to read I/O port 240 …
About to read I/O port 260 …
About to read I/O port 280 …
About to read I/O port 2A0 …
About to read I/O port 2C0 …
About to read I/O port 2E0 …
About to read I/O port 300 …
About to read I/O port 320 …
About to read I/O port 340 …
About to read I/O port 360 …
About to read I/O port 380 …
About to read I/O port 3A0 …
About to read I/O port 3C0 …
About to read I/O port 3E0 …
Looking for a 3Com 3c90x ethernet card …
Trying device id: 9000
Trying device id: 9050
Trying device id: 9055
Trying device id: 9058
Trying device id: 9200
Trying device id: 9001
Trying device id: 9051
Trying device id: 9056
Trying device id: 9004
Trying device id: 9005
Trying device id: 9006
Trying device id: 900a
Trying device id: 905a
Trying device id: 9800
Looking for a RealTek PCI ethernet card …
Searching for did: 8139, vid: 10ec
Searching for did: 1211, vid: 1113
No network cards detected
Hardware Support Account wrote:
Hi rsm,
Could you please post the output from pci -vvv
Thanks
Erick.
rsm <> raul@ottawa.com> > wrote:
Newbie network problems. I have searched and looked for answers through
the Help and in previous messages, but I am afraid I don’t know enough
about it.
Network card is not recognized (through nettrap -v, → “no network
card”)
pci -v → shows the card just fine (although it says “Macronix
MX98715/725” ?)
The card is a LinkSys NC100 (apparently the same as the LNE100), so I
tried the tulip driver, but it looks like it wouldn’t find the driver:
slay io-net
io-net -d tulip (I tried with other params as well), gets a message
that says it can’t find tulip under /dll or something like that.
I have a firewall setup on the other end of the cable, working just fine
under win98).
I am lost. How can I get networking going?
Thanks!
rsm