Help with SMC 8035 (Abocom FE2500) NIC

Alexander_Senkevitch · November 16, 2001, 5:27pm

I have a Compaq Presario 1621 laptop with CardBus slots and a SMC 8035 (Abocom FE2500 series dongleless) CardBus 10/100 PC Card. I have been having a heck of a time getting it to function at all. In fact, I have yet to be able to send ANY traffic across my network connection successfully. Until VERY recently, enum-pccard would not enumerate my adapter until I “hacked” the /etc/system/enum/devices/net file with an entry that was configured for the proper dev/ven id’s and bus topology. Now, at least when my system boots, I get a /dev/io-net/en0 device generated. I have plugged this card into both a LinkSys 8-port 10/100 autosense switch, AND a 3COM 5-port 10/100 autosense hub, both capable of full duplex, but neither have been successful. I have swapped out patch cables, and of course, I always verify that I am getting signal across (link lights, etc). The NIC itself always lights up with LINK, 100, FULL, PWR; which establish that the NIC is getting power, that it is running at 100Full Duplex, and that it has Link connectivity with the switch/hub.

Hardware specifics:
Notebook: Presario 1621
Chipset: TI PCI1131 Dual Socket CardBus
NIC: SMC 8035TX
Model#: SMC8035TX
P/N: 99-012055-000

I have included output for the following commands:
pin
pin cis
pin config
pci -vvvv
ifconfig en0
io-net -v -dtulip verbose=3 -ptcpip
2 ping’s

ANY input that could be provided would be GREAT! Thanks, this problem has been persisting for about 2.5 months now. I’m currently using RTP 6.1.0 (original GA dist. from ISO image from Aug.).

This bugs me because the SMC 8035 is listed as a supported NIC, what am I missing?

Outputs:

pin

Sock Func Type Flags PID Base Size IRQ
1 0 Network C—I-±–X–SAW 73742 0x500 256 10
0xffee0000 1024
1 Empty ----MF---------- None
2 Empty ----MF---------- None
2 Empty ----MF---------- None

\

pin cis

Socket : 1 - Function : 0
Link Target : ‘CIS’
Manufacturer ID : 0x13d1 0xab02
PC Card function : Network LAN Adapter
POST : 0x1
Tuple 0x22 link=2 : 01 02
Tuple 0x22 link=5 : 02 80 96 98 00
Tuple 0x22 link=5 : 02 00 e1 f5 05
Tuple 0x22 link=2 : 03 01
Card tuple version : 5.00
Manufacturer : CardBus
Name of Product : Fast Ethernet
Add’nl info (lot #) : V1.0
Add’nl info (programming):
Tuple 0x04 link=6 : 03 01 2a 00 00 00
Tuple 0x07 link=6 : 11 00 00 01 00 00
Tuple 0x07 link=6 : 02 00 00 01 00 00
Tuple 0x07 link=6 : 07 00 00 02 00 00
Tuple 0x05 link=10 : 41 39 01 b5 1e 02 b0 fc
: fe 84
Link Target : ‘CIS’
Manufacturer ID : 0x13d1 0xab02
PC Card function : Network LAN Adapter
POST : 0x1
Tuple 0x22 link=2 : 01 02
Tuple 0x22 link=5 : 02 80 96 98 00
Tuple 0x22 link=5 : 02 00 e1 f5 05
Tuple 0x22 link=2 : 03 01
Card tuple version : 5.00
Manufacturer : CardBus
Name of Product : Fast Ethernet
Add’nl info (lot #) : V1.0
Add’nl info (programming):
Tuple 0x04 link=6 : 03 01 2a 00 00 00
Tuple 0x07 link=6 : 11 00 00 01 00 00
Tuple 0x07 link=6 : 02 00 00 01 00 00
Tuple 0x07 link=6 : 07 00 00 02 00 00
Tuple 0x05 link=10 : 41 39 01 b5 1e 02 b0 fc
: fe 84

\

pin config

; socket 1
[device]
manufacturer = “CardBus”
product = “Fast Ethernet”
info1 = “V1.0”
info2 = “”
manufacturer = “CardBus”
product = “Fast Ethernet”
info1 = “V1.0”
info2 = “”
register = 0, 0x40, 0x40 ; level mode interrupts

\

pci -vvvv

PCI version = 2.10

Class = Bridge (Host/PCI)
Vendor ID = 1045h, OPTi Inc.
Device ID = c701h, 82C700 FireStar mobile chipset: host bridge
PCI index = 0h
Class Codes = 060000h
Revision ID = 32h
Bus number = 0
Device number = 0
Function num = 0
Status Reg = 280h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 02 20 71 32 00 84 30 00 00 00 5a 06 00 00
0x50: 00 00 00 00 40 c1 00 fc 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 f8 00 00 80 00 00 00 00

Class = Bridge (PCI/ISA)
Vendor ID = 1045h, OPTi Inc.
Device ID = c700h, 82C700 FireStar chipset, PCI-ISA bridge???
PCI index = 0h
Class Codes = 060100h
Revision ID = 31h
Bus number = 0
Device number = 1
Function num = 0
Status Reg = 280h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 02 c0 00 00 06 00 30 0a 30 3f 00 00 40 60
0x50: 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 f1 03 00 20 c0 00 00 00 00 00 00 00
0x70: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 20 00 00 4a 3e
0x90: 00 00 00 29 22 2b 21 00 00 3f 41 24 23 2a 2b 2b
0xA0: 00 00 00 00 00 00 00 00 80 41 dc 35 00 00 01 05
0xB0: 03 04 05 06 07 09 0a 0b 00 0b 01 00 01 00 00 00
0xC0: 10 32 50 76 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 7f 00 00 00 80 0f
0xE0: 00 00 00 00 00 00 00 00 0c 00 f0 e8 f0 e0 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac15h, PCI1131 Dual Socket PCI CardBus Controller
PCI index = 0h
Class Codes = 060700h
Revision ID = 1h
Bus number = 0
Device number = 10
Function num = 0
Status Reg = 200h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
ExCA Base Address = ffeff000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 1
Subordinate Bus Number = 1
Secondary Latency Timer = 20h
Memory Base 0 = ffec0000h
Memory Limit 0 = ffee0000h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 500h
I/O Limit 0 = 5fch
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 10
Bridge Control = 700h
Subsystem Vendor ID = e11h
Subsystem ID = b0c3h
Legacy Mode Base Address = 3e0h
System Control = 243020h
Retry Status = 0h
Card Control = 30h
Device Control = 74h
Buffer Control = 0h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 11 0e c3 b0 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 20 30 24 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 30 74 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac15h, PCI1131 Dual Socket PCI CardBus Controller
PCI index = 1h
Class Codes = 060700h
Revision ID = 1h
Bus number = 0
Device number = 10
Function num = 1
Status Reg = 200h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
ExCA Base Address = ffefe000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 2
Subordinate Bus Number = 2
Secondary Latency Timer = 20h
Memory Base 0 = 0h
Memory Limit 0 = 0h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 0h
I/O Limit 0 = 0h
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 2
PCI Int Pin = INT B
Interrupt line = 10
Bridge Control = 740h
Subsystem Vendor ID = e11h
Subsystem ID = b0c3h
Legacy Mode Base Address = 3e0h
System Control = 41020h
Retry Status = 0h
Card Control = 0h
Device Control = 74h
Buffer Control = 0h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 11 0e c3 b0 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 20 10 04 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 74 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Display (VGA)
Vendor ID = 10c8h, Neomagic Corporation
Device ID = 4h, NM2160 MagicGraph 128XD
PCI index = 0h
Class Codes = 030000h
Revision ID = 0h
Bus number = 0
Device number = 18
Function num = 0
Status Reg = 280h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 80h
Cache Line Size= 0h
PCI Mem Address = fd000000h prefetchable 32bit length 16777216 enabled
PCI Mem Address = fea00000h 32bit length 2097152 enabled
PCI Mem Address = fed00000h 32bit length 1048576 enabled
Max Lat = 255ns
Min Gnt = 16ns
PCI Int Pin = INT A
Interrupt line = 11
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Mass Storage (IDE)
Vendor ID = 1045h, OPTi Inc.
Device ID = d568h, 82C825 PCI bus master IDE controller
PCI index = 0h
Class Codes = 010180h
Revision ID = 30h
Bus number = 0
Device number = 20
Function num = 0
Status Reg = 280h
Command Reg = 1h
I/O space access enabled
Memory space access disabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
PCI IO Address = fcf0h length 16 enabled
Subsystem Vendor ID = e11h
Subsystem ID = b0c2h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 20 00 16 00 00 00 00 fa 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Network (Ethernet)
Vendor ID = 13d1h, Abocom Systems Inc
Device ID = ab02h, Unknown Unknown
PCI index = 0h
Class Codes = 020000h
Revision ID = 11h
Bus number = 1
Device number = 0
Function num = 0
Status Reg = 290h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
PCI IO Address = 500h length 256 enabled
PCI Mem Address = ffee0000h 32bit length 1024 enabled
CardBus CIS Pointer = 202h
Subsystem Vendor ID = 13d1h
Subsystem ID = ab02h
PCI Expansion ROM = ffec0000h length 131072 disabled
Max Lat = 255ns
Min Gnt = 255ns
PCI Int Pin = INT A
Interrupt line = 10
Capabilities Pointer = c0h
Capability ID = 1h
Capabilities = fe02h - 0h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 17 13 81 09 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 01 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

\

ifconfig en0

en0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 10.1.2.34 netmask 0xfffffc00 broadcast 10.1.3.255

\

io-net -v -dtulip verbose=3 -ptcpip

tulip CLI Arguments: verbose=3 multicast=true
tulip: scanning for Vendor=0x1011 Device=0x0002
tulip: scanning for Vendor=0x1011 Device=0x0008
tulip: scanning for Vendor=0x1011 Device=0x0009
tulip: scanning for Vendor=0x1011 Device=0x0014
tulip: scanning for Vendor=0x1011 Device=0x0019
tulip: scanning for Vendor=0x8086 Device=0x0039
tulip: scanning for Vendor=0x11ad Device=0x0002
tulip: scanning for Vendor=0x11ad Device=0x0168
tulip: scanning for Vendor=0x1317 Device=0x0985
tulip: scanning for Vendor=0x1317 Device=0x0981
tulip: scanning for Vendor=0x10d9 Device=0x0531
tulip: scanning for Vendor=0x115d Device=0x0003
tulip: scanning for Vendor=0x13d1 Device=0xab02
tulip: RegisterDeviceInstance(nic=0x8056a54, ion=0x8055780)
tulip Hardware Config: Vendor=0x13d1 Device=0xab02 chipset=2500
tulip: host memory, rx/tx Packets & Descriptors allocated rx=32 tx=20
Attempting MII Detection
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
LinkSense : Failure
AutoDetection Completed
Default Media Selected : MII
Media Selected : MII No Link
Tulip: Abocom FE2500
Vendor … 0x13d1
Device … 0xab02
Revision … 0x0
I/O port base … 0x500
Interrupt … 0xa
MAC address … 00e098 963841
tulip: advertise to io-net Vendor 0x13d1 Device 0xab02 Chipset 2500
tulip: advertise to io-net Vendor 0x13d1 Device 0xab02 Chipset 2500
tulip: advertise to io-net Vendor 0x13d1 Device 0xab02 Chipset 2500
tulip (Net: 0): Link Down, Check Cabling
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)

…[preceeding message suppressed, repeated 63 times]…

\

ping 10.1.2.34 [my own IP addr]

PING 10.3.200.163 (10.3.200.163): 56 data bytes
64 bytes from 10.3.200.163: icmp_seq=0 ttl=255 time=1 ms
64 bytes from 10.3.200.163: icmp_seq=1 ttl=255 time=0 ms
64 bytes from 10.3.200.163: icmp_seq=2 ttl=255 time=0 ms
64 bytes from 10.3.200.163: icmp_seq=3 ttl=255 time=0 ms
64 bytes from 10.3.200.163: icmp_seq=4 ttl=255 time=0 ms

— 10.1.2.34 ping statistics —
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 0/0/1 ms

\

ping 10.1.0.1 [my local gateway]

PING 10.1.0.1 (10.1.0.1): 56 data bytes
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1

— 10.1.0.1 ping statistics —
5 packets transmitted, 0 packets received, 100% packet loss

Thanks,

Alex Senkevitch

Alexander_Senkevitch · November 20, 2001, 6:49pm

Does anyone have any insight into this at all? It’s getting to be quit frustrating at this point.

Thanks,

Alex Senkevitch

“Alexander Senkevitch” <asenkevitch@hotmail.com> wrote in message news:9t3i75$ota$1@inn.qnx.com…
I have a Compaq Presario 1621 laptop with CardBus slots and a SMC 8035 (Abocom FE2500 series dongleless) CardBus 10/100 PC Card. I have been having a heck of a time getting it to function at all. In fact, I have yet to be able to send ANY traffic across my network connection successfully. Until VERY recently, enum-pccard would not enumerate my adapter until I “hacked” the /etc/system/enum/devices/net file with an entry that was configured for the proper dev/ven id’s and bus topology. Now, at least when my system boots, I get a /dev/io-net/en0 device generated. I have plugged this card into both a LinkSys 8-port 10/100 autosense switch, AND a 3COM 5-port 10/100 autosense hub, both capable of full duplex, but neither have been successful. I have swapped out patch cables, and of course, I always verify that I am getting signal across (link lights, etc). The NIC itself always lights up with LINK, 100, FULL, PWR; which establish that the NIC is getting power, that it is running at 100Full Duplex, and that it has Link connectivity with the switch/hub.

Hardware specifics:
Notebook: Presario 1621
Chipset: TI PCI1131 Dual Socket CardBus
NIC: SMC 8035TX
Model#: SMC8035TX
P/N: 99-012055-000

I have included output for the following commands:
pin
pin cis
pin config
pci -vvvv
ifconfig en0
io-net -v -dtulip verbose=3 -ptcpip
2 ping’s

ANY input that could be provided would be GREAT! Thanks, this problem has been persisting for about 2.5 months now. I’m currently using RTP 6.1.0 (original GA dist. from ISO image from Aug.).

This bugs me because the SMC 8035 is listed as a supported NIC, what am I missing?

Outputs:

pin

Sock Func Type Flags PID Base Size IRQ
1 0 Network C—I-±–X–SAW 73742 0x500 256 10
0xffee0000 1024
1 Empty ----MF---------- None
2 Empty ----MF---------- None
2 Empty ----MF---------- None

\

pin cis

Socket : 1 - Function : 0
Link Target : ‘CIS’
Manufacturer ID : 0x13d1 0xab02
PC Card function : Network LAN Adapter
POST : 0x1
Tuple 0x22 link=2 : 01 02
Tuple 0x22 link=5 : 02 80 96 98 00
Tuple 0x22 link=5 : 02 00 e1 f5 05
Tuple 0x22 link=2 : 03 01
Card tuple version : 5.00
Manufacturer : CardBus
Name of Product : Fast Ethernet
Add’nl info (lot #) : V1.0
Add’nl info (programming):
Tuple 0x04 link=6 : 03 01 2a 00 00 00
Tuple 0x07 link=6 : 11 00 00 01 00 00
Tuple 0x07 link=6 : 02 00 00 01 00 00
Tuple 0x07 link=6 : 07 00 00 02 00 00
Tuple 0x05 link=10 : 41 39 01 b5 1e 02 b0 fc
: fe 84
Link Target : ‘CIS’
Manufacturer ID : 0x13d1 0xab02
PC Card function : Network LAN Adapter
POST : 0x1
Tuple 0x22 link=2 : 01 02
Tuple 0x22 link=5 : 02 80 96 98 00
Tuple 0x22 link=5 : 02 00 e1 f5 05
Tuple 0x22 link=2 : 03 01
Card tuple version : 5.00
Manufacturer : CardBus
Name of Product : Fast Ethernet
Add’nl info (lot #) : V1.0
Add’nl info (programming):
Tuple 0x04 link=6 : 03 01 2a 00 00 00
Tuple 0x07 link=6 : 11 00 00 01 00 00
Tuple 0x07 link=6 : 02 00 00 01 00 00
Tuple 0x07 link=6 : 07 00 00 02 00 00
Tuple 0x05 link=10 : 41 39 01 b5 1e 02 b0 fc
: fe 84

\

pin config

; socket 1
[device]
manufacturer = “CardBus”
product = “Fast Ethernet”
info1 = “V1.0”
info2 = “”
manufacturer = “CardBus”
product = “Fast Ethernet”
info1 = “V1.0”
info2 = “”
register = 0, 0x40, 0x40 ; level mode interrupts

\

pci -vvvv

PCI version = 2.10

Class = Bridge (Host/PCI)
Vendor ID = 1045h, OPTi Inc.
Device ID = c701h, 82C700 FireStar mobile chipset: host bridge
PCI index = 0h
Class Codes = 060000h
Revision ID = 32h
Bus number = 0
Device number = 0
Function num = 0
Status Reg = 280h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 02 20 71 32 00 84 30 00 00 00 5a 06 00 00
0x50: 00 00 00 00 40 c1 00 fc 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 f8 00 00 80 00 00 00 00

Class = Bridge (PCI/ISA)
Vendor ID = 1045h, OPTi Inc.
Device ID = c700h, 82C700 FireStar chipset, PCI-ISA bridge???
PCI index = 0h
Class Codes = 060100h
Revision ID = 31h
Bus number = 0
Device number = 1
Function num = 0
Status Reg = 280h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 02 c0 00 00 06 00 30 0a 30 3f 00 00 40 60
0x50: 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 f1 03 00 20 c0 00 00 00 00 00 00 00
0x70: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 20 00 00 4a 3e
0x90: 00 00 00 29 22 2b 21 00 00 3f 41 24 23 2a 2b 2b
0xA0: 00 00 00 00 00 00 00 00 80 41 dc 35 00 00 01 05
0xB0: 03 04 05 06 07 09 0a 0b 00 0b 01 00 01 00 00 00
0xC0: 10 32 50 76 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 7f 00 00 00 80 0f
0xE0: 00 00 00 00 00 00 00 00 0c 00 f0 e8 f0 e0 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac15h, PCI1131 Dual Socket PCI CardBus Controller
PCI index = 0h
Class Codes = 060700h
Revision ID = 1h
Bus number = 0
Device number = 10
Function num = 0
Status Reg = 200h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
ExCA Base Address = ffeff000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 1
Subordinate Bus Number = 1
Secondary Latency Timer = 20h
Memory Base 0 = ffec0000h
Memory Limit 0 = ffee0000h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 500h
I/O Limit 0 = 5fch
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 10
Bridge Control = 700h
Subsystem Vendor ID = e11h
Subsystem ID = b0c3h
Legacy Mode Base Address = 3e0h
System Control = 243020h
Retry Status = 0h
Card Control = 30h
Device Control = 74h
Buffer Control = 0h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 11 0e c3 b0 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 20 30 24 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 30 74 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac15h, PCI1131 Dual Socket PCI CardBus Controller
PCI index = 1h
Class Codes = 060700h
Revision ID = 1h
Bus number = 0
Device number = 10
Function num = 1
Status Reg = 200h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
ExCA Base Address = ffefe000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 2
Subordinate Bus Number = 2
Secondary Latency Timer = 20h
Memory Base 0 = 0h
Memory Limit 0 = 0h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 0h
I/O Limit 0 = 0h
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 2
PCI Int Pin = INT B
Interrupt line = 10
Bridge Control = 740h
Subsystem Vendor ID = e11h
Subsystem ID = b0c3h
Legacy Mode Base Address = 3e0h
System Control = 41020h
Retry Status = 0h
Card Control = 0h
Device Control = 74h
Buffer Control = 0h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 11 0e c3 b0 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 20 10 04 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 74 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Display (VGA)
Vendor ID = 10c8h, Neomagic Corporation
Device ID = 4h, NM2160 MagicGraph 128XD
PCI index = 0h
Class Codes = 030000h
Revision ID = 0h
Bus number = 0
Device number = 18
Function num = 0
Status Reg = 280h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 80h
Cache Line Size= 0h
PCI Mem Address = fd000000h prefetchable 32bit length 16777216 enabled
PCI Mem Address = fea00000h 32bit length 2097152 enabled
PCI Mem Address = fed00000h 32bit length 1048576 enabled
Max Lat = 255ns
Min Gnt = 16ns
PCI Int Pin = INT A
Interrupt line = 11
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Mass Storage (IDE)
Vendor ID = 1045h, OPTi Inc.
Device ID = d568h, 82C825 PCI bus master IDE controller
PCI index = 0h
Class Codes = 010180h
Revision ID = 30h
Bus number = 0
Device number = 20
Function num = 0
Status Reg = 280h
Command Reg = 1h
I/O space access enabled
Memory space access disabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
PCI IO Address = fcf0h length 16 enabled
Subsystem Vendor ID = e11h
Subsystem ID = b0c2h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 20 00 16 00 00 00 00 fa 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Network (Ethernet)
Vendor ID = 13d1h, Abocom Systems Inc
Device ID = ab02h, Unknown Unknown
PCI index = 0h
Class Codes = 020000h
Revision ID = 11h
Bus number = 1
Device number = 0
Function num = 0
Status Reg = 290h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
PCI IO Address = 500h length 256 enabled
PCI Mem Address = ffee0000h 32bit length 1024 enabled
CardBus CIS Pointer = 202h
Subsystem Vendor ID = 13d1h
Subsystem ID = ab02h
PCI Expansion ROM = ffec0000h length 131072 disabled
Max Lat = 255ns
Min Gnt = 255ns
PCI Int Pin = INT A
Interrupt line = 10
Capabilities Pointer = c0h
Capability ID = 1h
Capabilities = fe02h - 0h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 17 13 81 09 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 01 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

\

ifconfig en0

en0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 10.1.2.34 netmask 0xfffffc00 broadcast 10.1.3.255

\

io-net -v -dtulip verbose=3 -ptcpip

tulip CLI Arguments: verbose=3 multicast=true
tulip: scanning for Vendor=0x1011 Device=0x0002
tulip: scanning for Vendor=0x1011 Device=0x0008
tulip: scanning for Vendor=0x1011 Device=0x0009
tulip: scanning for Vendor=0x1011 Device=0x0014
tulip: scanning for Vendor=0x1011 Device=0x0019
tulip: scanning for Vendor=0x8086 Device=0x0039
tulip: scanning for Vendor=0x11ad Device=0x0002
tulip: scanning for Vendor=0x11ad Device=0x0168
tulip: scanning for Vendor=0x1317 Device=0x0985
tulip: scanning for Vendor=0x1317 Device=0x0981
tulip: scanning for Vendor=0x10d9 Device=0x0531
tulip: scanning for Vendor=0x115d Device=0x0003
tulip: scanning for Vendor=0x13d1 Device=0xab02
tulip: RegisterDeviceInstance(nic=0x8056a54, ion=0x8055780)
tulip Hardware Config: Vendor=0x13d1 Device=0xab02 chipset=2500
tulip: host memory, rx/tx Packets & Descriptors allocated rx=32 tx=20
Attempting MII Detection
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
LinkSense : Failure
AutoDetection Completed
Default Media Selected : MII
Media Selected : MII No Link
Tulip: Abocom FE2500
Vendor … 0x13d1
Device … 0xab02
Revision … 0x0
I/O port base … 0x500
Interrupt … 0xa
MAC address … 00e098 963841
tulip: advertise to io-net Vendor 0x13d1 Device 0xab02 Chipset 2500
tulip: advertise to io-net Vendor 0x13d1 Device 0xab02 Chipset 2500
tulip: advertise to io-net Vendor 0x13d1 Device 0xab02 Chipset 2500
tulip (Net: 0): Link Down, Check Cabling
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)

…[preceeding message suppressed, repeated 63 times]…

\

ping 10.1.2.34 [my own IP addr]

PING 10.3.200.163 (10.3.200.163): 56 data bytes
64 bytes from 10.3.200.163: icmp_seq=0 ttl=255 time=1 ms
64 bytes from 10.3.200.163: icmp_seq=1 ttl=255 time=0 ms
64 bytes from 10.3.200.163: icmp_seq=2 ttl=255 time=0 ms
64 bytes from 10.3.200.163: icmp_seq=3 ttl=255 time=0 ms
64 bytes from 10.3.200.163: icmp_seq=4 ttl=255 time=0 ms

— 10.1.2.34 ping statistics —
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 0/0/1 ms

\

ping 10.1.0.1 [my local gateway]

PING 10.1.0.1 (10.1.0.1): 56 data bytes
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1

— 10.1.0.1 ping statistics —
5 packets transmitted, 0 packets received, 100% packet loss

Thanks,

Alex Senkevitch

Hardware_Support_Acc · November 20, 2001, 8:18pm

Hi Alexander,

How are you starting the driver? Have you tried starting the driver manually?
What is the output of pidin ar?

(Thanks for the other output as well).

Erick.

Alexander Senkevitch <asenkevitch@hotmail.com> wrote:

I have a Compaq Presario 1621 laptop with CardBus slots and a SMC 8035 (Abocom FE2500 series dongleless) CardBus 10/100 PC Card. I have been having a heck of a time getting it to function at all. In fact, I have yet to be able to send ANY traffic across my network connection successfully. Until VERY recently, enum-pccard would not enumerate my adapter until I “hacked” the /etc/system/enum/devices/net file with an entry that was configured for the proper dev/ven id’s and bus topology. Now, at least wh
en my system boots, I get a /dev/io-net/en0 device generated. I have plugged this card into both a LinkSys 8-port 10/100 autosense switch, AND a 3COM 5-port 10/100 autosense hub, both capable of full duplex, but neither have been successful. I have swapped out patch cables, and of course, I always verify that I am getting signal across (link lights, etc). The NIC itself always lights up with LINK, 100, FULL, PWR; which establish that the NIC is getting power, that it is running at 100Full Duplex, and th

at it has Link connectivity with the switch/hub.

Hardware specifics:
Notebook: Presario 1621
Chipset: TI PCI1131 Dual Socket CardBus
NIC: SMC 8035TX
Model#: SMC8035TX
P/N: 99-012055-000

I have included output for the following commands:
pin
pin cis
pin config
pci -vvvv
ifconfig en0
io-net -v -dtulip verbose=3 -ptcpip
2 ping’s

ANY input that could be provided would be GREAT! Thanks, this problem has been persisting for about 2.5 months now. I’m currently using RTP 6.1.0 (original GA dist. from ISO image from Aug.).

This bugs me because the SMC 8035 is listed as a supported NIC, what am I missing?

Outputs:

pin

Sock Func Type Flags PID Base Size IRQ
1 0 Network C—I-±–X–SAW 73742 0x500 256 10
0xffee0000 1024
1 Empty ----MF---------- None
2 Empty ----MF---------- None
2 Empty ----MF---------- None

pin cis

Socket : 1 - Function : 0
Link Target : ‘CIS’
Manufacturer ID : 0x13d1 0xab02
PC Card function : Network LAN Adapter
POST : 0x1
Tuple 0x22 link=2 : 01 02
Tuple 0x22 link=5 : 02 80 96 98 00
Tuple 0x22 link=5 : 02 00 e1 f5 05
Tuple 0x22 link=2 : 03 01
Card tuple version : 5.00
Manufacturer : CardBus
Name of Product : Fast Ethernet
Add’nl info (lot #) : V1.0
Add’nl info (programming):
Tuple 0x04 link=6 : 03 01 2a 00 00 00
Tuple 0x07 link=6 : 11 00 00 01 00 00
Tuple 0x07 link=6 : 02 00 00 01 00 00
Tuple 0x07 link=6 : 07 00 00 02 00 00
Tuple 0x05 link=10 : 41 39 01 b5 1e 02 b0 fc
: fe 84
Link Target : ‘CIS’
Manufacturer ID : 0x13d1 0xab02
PC Card function : Network LAN Adapter
POST : 0x1
Tuple 0x22 link=2 : 01 02
Tuple 0x22 link=5 : 02 80 96 98 00
Tuple 0x22 link=5 : 02 00 e1 f5 05
Tuple 0x22 link=2 : 03 01
Card tuple version : 5.00
Manufacturer : CardBus
Name of Product : Fast Ethernet
Add’nl info (lot #) : V1.0
Add’nl info (programming):
Tuple 0x04 link=6 : 03 01 2a 00 00 00
Tuple 0x07 link=6 : 11 00 00 01 00 00
Tuple 0x07 link=6 : 02 00 00 01 00 00
Tuple 0x07 link=6 : 07 00 00 02 00 00
Tuple 0x05 link=10 : 41 39 01 b5 1e 02 b0 fc
: fe 84

pin config

; socket 1
[device]
manufacturer = “CardBus”
product = “Fast Ethernet”
info1 = “V1.0”
info2 = “”
manufacturer = “CardBus”
product = “Fast Ethernet”
info1 = “V1.0”
info2 = “”
register = 0, 0x40, 0x40 ; level mode interrupts

pci -vvvv

PCI version = 2.10

Class = Bridge (Host/PCI)
Vendor ID = 1045h, OPTi Inc.
Device ID = c701h, 82C700 FireStar mobile chipset: host bridge
PCI index = 0h
Class Codes = 060000h
Revision ID = 32h
Bus number = 0
Device number = 0
Function num = 0
Status Reg = 280h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 02 20 71 32 00 84 30 00 00 00 5a 06 00 00
0x50: 00 00 00 00 40 c1 00 fc 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 f8 00 00 80 00 00 00 00

Class = Bridge (PCI/ISA)
Vendor ID = 1045h, OPTi Inc.
Device ID = c700h, 82C700 FireStar chipset, PCI-ISA bridge???
PCI index = 0h
Class Codes = 060100h
Revision ID = 31h
Bus number = 0
Device number = 1
Function num = 0
Status Reg = 280h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 02 c0 00 00 06 00 30 0a 30 3f 00 00 40 60
0x50: 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 f1 03 00 20 c0 00 00 00 00 00 00 00
0x70: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 20 00 00 4a 3e
0x90: 00 00 00 29 22 2b 21 00 00 3f 41 24 23 2a 2b 2b
0xA0: 00 00 00 00 00 00 00 00 80 41 dc 35 00 00 01 05
0xB0: 03 04 05 06 07 09 0a 0b 00 0b 01 00 01 00 00 00
0xC0: 10 32 50 76 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 7f 00 00 00 80 0f
0xE0: 00 00 00 00 00 00 00 00 0c 00 f0 e8 f0 e0 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac15h, PCI1131 Dual Socket PCI CardBus Controller
PCI index = 0h
Class Codes = 060700h
Revision ID = 1h
Bus number = 0
Device number = 10
Function num = 0
Status Reg = 200h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
ExCA Base Address = ffeff000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 1
Subordinate Bus Number = 1
Secondary Latency Timer = 20h
Memory Base 0 = ffec0000h
Memory Limit 0 = ffee0000h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 500h
I/O Limit 0 = 5fch
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 10
Bridge Control = 700h
Subsystem Vendor ID = e11h
Subsystem ID = b0c3h
Legacy Mode Base Address = 3e0h
System Control = 243020h
Retry Status = 0h
Card Control = 30h
Device Control = 74h
Buffer Control = 0h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 11 0e c3 b0 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 20 30 24 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 30 74 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac15h, PCI1131 Dual Socket PCI CardBus Controller
PCI index = 1h
Class Codes = 060700h
Revision ID = 1h
Bus number = 0
Device number = 10
Function num = 1
Status Reg = 200h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
ExCA Base Address = ffefe000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 2
Subordinate Bus Number = 2
Secondary Latency Timer = 20h
Memory Base 0 = 0h
Memory Limit 0 = 0h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 0h
I/O Limit 0 = 0h
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 2
PCI Int Pin = INT B
Interrupt line = 10
Bridge Control = 740h
Subsystem Vendor ID = e11h
Subsystem ID = b0c3h
Legacy Mode Base Address = 3e0h
System Control = 41020h
Retry Status = 0h
Card Control = 0h
Device Control = 74h
Buffer Control = 0h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 11 0e c3 b0 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 20 10 04 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 74 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Display (VGA)
Vendor ID = 10c8h, Neomagic Corporation
Device ID = 4h, NM2160 MagicGraph 128XD
PCI index = 0h
Class Codes = 030000h
Revision ID = 0h
Bus number = 0
Device number = 18
Function num = 0
Status Reg = 280h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 80h
Cache Line Size= 0h
PCI Mem Address = fd000000h prefetchable 32bit length 16777216 enabled
PCI Mem Address = fea00000h 32bit length 2097152 enabled
PCI Mem Address = fed00000h 32bit length 1048576 enabled
Max Lat = 255ns
Min Gnt = 16ns
PCI Int Pin = INT A
Interrupt line = 11
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Mass Storage (IDE)
Vendor ID = 1045h, OPTi Inc.
Device ID = d568h, 82C825 PCI bus master IDE controller
PCI index = 0h
Class Codes = 010180h
Revision ID = 30h
Bus number = 0
Device number = 20
Function num = 0
Status Reg = 280h
Command Reg = 1h
I/O space access enabled
Memory space access disabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
PCI IO Address = fcf0h length 16 enabled
Subsystem Vendor ID = e11h
Subsystem ID = b0c2h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 20 00 16 00 00 00 00 fa 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Network (Ethernet)
Vendor ID = 13d1h, Abocom Systems Inc
Device ID = ab02h, Unknown Unknown
PCI index = 0h
Class Codes = 020000h
Revision ID = 11h
Bus number = 1
Device number = 0
Function num = 0
Status Reg = 290h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
PCI IO Address = 500h length 256 enabled
PCI Mem Address = ffee0000h 32bit length 1024 enabled
CardBus CIS Pointer = 202h
Subsystem Vendor ID = 13d1h
Subsystem ID = ab02h
PCI Expansion ROM = ffec0000h length 131072 disabled
Max Lat = 255ns
Min Gnt = 255ns
PCI Int Pin = INT A
Interrupt line = 10
Capabilities Pointer = c0h
Capability ID = 1h
Capabilities = fe02h - 0h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 17 13 81 09 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 01 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

ifconfig en0

en0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 10.1.2.34 netmask 0xfffffc00 broadcast 10.1.3.255

io-net -v -dtulip verbose=3 -ptcpip

tulip CLI Arguments: verbose=3 multicast=true
tulip: scanning for Vendor=0x1011 Device=0x0002
tulip: scanning for Vendor=0x1011 Device=0x0008
tulip: scanning for Vendor=0x1011 Device=0x0009
tulip: scanning for Vendor=0x1011 Device=0x0014
tulip: scanning for Vendor=0x1011 Device=0x0019
tulip: scanning for Vendor=0x8086 Device=0x0039
tulip: scanning for Vendor=0x11ad Device=0x0002
tulip: scanning for Vendor=0x11ad Device=0x0168
tulip: scanning for Vendor=0x1317 Device=0x0985
tulip: scanning for Vendor=0x1317 Device=0x0981
tulip: scanning for Vendor=0x10d9 Device=0x0531
tulip: scanning for Vendor=0x115d Device=0x0003
tulip: scanning for Vendor=0x13d1 Device=0xab02
tulip: RegisterDeviceInstance(nic=0x8056a54, ion=0x8055780)
tulip Hardware Config: Vendor=0x13d1 Device=0xab02 chipset=2500
tulip: host memory, rx/tx Packets & Descriptors allocated rx=32 tx=20
Attempting MII Detection
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
LinkSense : Failure
AutoDetection Completed
Default Media Selected : MII
Media Selected : MII No Link
Tulip: Abocom FE2500
Vendor … 0x13d1
Device … 0xab02
Revision … 0x0
I/O port base … 0x500
Interrupt … 0xa
MAC address … 00e098 963841
tulip: advertise to io-net Vendor 0x13d1 Device 0xab02 Chipset 2500
tulip: advertise to io-net Vendor 0x13d1 Device 0xab02 Chipset 2500
tulip: advertise to io-net Vendor 0x13d1 Device 0xab02 Chipset 2500
tulip (Net: 0): Link Down, Check Cabling
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)

…[preceeding message suppressed, repeated 63 times]…

ping 10.1.2.34 [my own IP addr]

PING 10.3.200.163 (10.3.200.163): 56 data bytes
64 bytes from 10.3.200.163: icmp_seq=0 ttl=255 time=1 ms
64 bytes from 10.3.200.163: icmp_seq=1 ttl=255 time=0 ms
64 bytes from 10.3.200.163: icmp_seq=2 ttl=255 time=0 ms
64 bytes from 10.3.200.163: icmp_seq=3 ttl=255 time=0 ms
64 bytes from 10.3.200.163: icmp_seq=4 ttl=255 time=0 ms

— 10.1.2.34 ping statistics —
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 0/0/1 ms

ping 10.1.0.1 [my local gateway]

PING 10.1.0.1 (10.1.0.1): 56 data bytes
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1

— 10.1.0.1 ping statistics —
5 packets transmitted, 0 packets received, 100% packet loss

Thanks,

Alex Senkevitch

Alexander_Senkevitch · November 20, 2001, 9:54pm

I can (at the moment) answer your first two questions. I will post the output of ‘pidin ar’ tonight once I am in front of the system in question.

Q1:
You will have to forgive me, as the following content is being generated from memory and not from actually seeing it on the console.
I am, currently, starting the driver through a modified /etc/system/enum/devices/net file entry whereby I added the line:
device(cardbus, dev=ab02, ven=13d1)
ABOVE an already existing entry in the ‘net’ file, which was an already existing ‘cardbus’ entry that also happened to utilize the devn-tulip.so shared object, basically piggy-backing on that existing entries configuration. Prior to this modification, the card in question (SMC 8035TX) would NOT be enumerated by enum-pccard. I would have no choice but to go the manual ‘rc.local’ route of hard coding an io-net statement. Now, it is (apparently) properly enumerated (ie, /dev/io-net/en0 is created), and net.cfg is referenced by netmanager.

Q2:
Yes, prior to creating the hacked ‘net’ file, I was starting the process manually via either the CLI or an rc.local file entry. The entries looked as follows:
slay /dev/io-net
io-net -dtulip -pttcpip if=en0:1.2.3.4:255.255.255.0

or -

slay /dev/io-net
io-net -dtulip -ptcpip
sleep 2
ifconfig en0 1.2.3.4 netmask 255.255.255.0 broadcast 1.2.3.255
route add default 1.2.3.1

The latter block would also possibly be executed via the CLI. As a further note, I am currently running QNXRTP 6.1.0A, with no change in function.

As close as I can figure, the “tulip” chipset is not talking with the MII PHY to determine link status/media from the MII Media Description Table.

Thanks,

Alex

PS, you can additionally reference a previous post on the matter made on 7/18/2001 by me in the ‘qdn.public.ddk.network’ group titled “MII register mis-read in devn-tulip.so?”

“Hardware Support Account” <hw@qnx.com> wrote in message news:9tedr2$996$2@nntp.qnx.com…

Hi Alexander,

How are you starting the driver? Have you tried starting the driver manually?
What is the output of pidin ar?

(Thanks for the other output as well).

Erick.

Alexander Senkevitch <> asenkevitch@hotmail.com> > wrote:

I have a Compaq Presario 1621 laptop with CardBus slots and a SMC 8035 (Abocom FE2500 series dongleless) CardBus 10/100 PC Card. I have been having a heck of a time getting it to function at all. In fact, I have yet to be able to send ANY traffic across my network connection successfully. Until VERY recently, enum-pccard would not enumerate my adapter until I “hacked” the /etc/system/enum/devices/net file with an entry that was configured for the proper dev/ven id’s and bus topology. Now, at least wh
en my system boots, I get a /dev/io-net/en0 device generated. I have plugged this card into both a LinkSys 8-port 10/100 autosense switch, AND a 3COM 5-port 10/100 autosense hub, both capable of full duplex, but neither have been successful. I have swapped out patch cables, and of course, I always verify that I am getting signal across (link lights, etc). The NIC itself always lights up with LINK, 100, FULL, PWR; which establish that the NIC is getting power, that it is running at 100Full Duplex, and th
at it has Link connectivity with the switch/hub.

Hardware specifics:
Notebook: Presario 1621
Chipset: TI PCI1131 Dual Socket CardBus
NIC: SMC 8035TX
Model#: SMC8035TX
P/N: 99-012055-000

I have included output for the following commands:
pin
pin cis
pin config
pci -vvvv
ifconfig en0
io-net -v -dtulip verbose=3 -ptcpip
2 ping’s

ANY input that could be provided would be GREAT! Thanks, this problem has been persisting for about 2.5 months now. I’m currently using RTP 6.1.0 (original GA dist. from ISO image from Aug.).

This bugs me because the SMC 8035 is listed as a supported NIC, what am I missing?

Outputs:

pin

Sock Func Type Flags PID Base Size IRQ
1 0 Network C—I-±–X–SAW 73742 0x500 256 10
0xffee0000 1024
1 Empty ----MF---------- None
2 Empty ----MF---------- None
2 Empty ----MF---------- None

\

pin cis

Socket : 1 - Function : 0
Link Target : ‘CIS’
Manufacturer ID : 0x13d1 0xab02
PC Card function : Network LAN Adapter
POST : 0x1
Tuple 0x22 link=2 : 01 02
Tuple 0x22 link=5 : 02 80 96 98 00
Tuple 0x22 link=5 : 02 00 e1 f5 05
Tuple 0x22 link=2 : 03 01
Card tuple version : 5.00
Manufacturer : CardBus
Name of Product : Fast Ethernet
Add’nl info (lot #) : V1.0
Add’nl info (programming):
Tuple 0x04 link=6 : 03 01 2a 00 00 00
Tuple 0x07 link=6 : 11 00 00 01 00 00
Tuple 0x07 link=6 : 02 00 00 01 00 00
Tuple 0x07 link=6 : 07 00 00 02 00 00
Tuple 0x05 link=10 : 41 39 01 b5 1e 02 b0 fc
: fe 84
Link Target : ‘CIS’
Manufacturer ID : 0x13d1 0xab02
PC Card function : Network LAN Adapter
POST : 0x1
Tuple 0x22 link=2 : 01 02
Tuple 0x22 link=5 : 02 80 96 98 00
Tuple 0x22 link=5 : 02 00 e1 f5 05
Tuple 0x22 link=2 : 03 01
Card tuple version : 5.00
Manufacturer : CardBus
Name of Product : Fast Ethernet
Add’nl info (lot #) : V1.0
Add’nl info (programming):
Tuple 0x04 link=6 : 03 01 2a 00 00 00
Tuple 0x07 link=6 : 11 00 00 01 00 00
Tuple 0x07 link=6 : 02 00 00 01 00 00
Tuple 0x07 link=6 : 07 00 00 02 00 00
Tuple 0x05 link=10 : 41 39 01 b5 1e 02 b0 fc
: fe 84

\

pin config

; socket 1
[device]
manufacturer = “CardBus”
product = “Fast Ethernet”
info1 = “V1.0”
info2 = “”
manufacturer = “CardBus”
product = “Fast Ethernet”
info1 = “V1.0”
info2 = “”
register = 0, 0x40, 0x40 ; level mode interrupts

\

pci -vvvv

PCI version = 2.10

Class = Bridge (Host/PCI)
Vendor ID = 1045h, OPTi Inc.
Device ID = c701h, 82C700 FireStar mobile chipset: host bridge
PCI index = 0h
Class Codes = 060000h
Revision ID = 32h
Bus number = 0
Device number = 0
Function num = 0
Status Reg = 280h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 02 20 71 32 00 84 30 00 00 00 5a 06 00 00
0x50: 00 00 00 00 40 c1 00 fc 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 f8 00 00 80 00 00 00 00

Class = Bridge (PCI/ISA)
Vendor ID = 1045h, OPTi Inc.
Device ID = c700h, 82C700 FireStar chipset, PCI-ISA bridge???
PCI index = 0h
Class Codes = 060100h
Revision ID = 31h
Bus number = 0
Device number = 1
Function num = 0
Status Reg = 280h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 02 c0 00 00 06 00 30 0a 30 3f 00 00 40 60
0x50: 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 f1 03 00 20 c0 00 00 00 00 00 00 00
0x70: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 20 00 00 4a 3e
0x90: 00 00 00 29 22 2b 21 00 00 3f 41 24 23 2a 2b 2b
0xA0: 00 00 00 00 00 00 00 00 80 41 dc 35 00 00 01 05
0xB0: 03 04 05 06 07 09 0a 0b 00 0b 01 00 01 00 00 00
0xC0: 10 32 50 76 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 7f 00 00 00 80 0f
0xE0: 00 00 00 00 00 00 00 00 0c 00 f0 e8 f0 e0 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac15h, PCI1131 Dual Socket PCI CardBus Controller
PCI index = 0h
Class Codes = 060700h
Revision ID = 1h
Bus number = 0
Device number = 10
Function num = 0
Status Reg = 200h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
ExCA Base Address = ffeff000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 1
Subordinate Bus Number = 1
Secondary Latency Timer = 20h
Memory Base 0 = ffec0000h
Memory Limit 0 = ffee0000h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 500h
I/O Limit 0 = 5fch
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 10
Bridge Control = 700h
Subsystem Vendor ID = e11h
Subsystem ID = b0c3h
Legacy Mode Base Address = 3e0h
System Control = 243020h
Retry Status = 0h
Card Control = 30h
Device Control = 74h
Buffer Control = 0h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 11 0e c3 b0 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 20 30 24 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 30 74 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac15h, PCI1131 Dual Socket PCI CardBus Controller
PCI index = 1h
Class Codes = 060700h
Revision ID = 1h
Bus number = 0
Device number = 10
Function num = 1
Status Reg = 200h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
ExCA Base Address = ffefe000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 2
Subordinate Bus Number = 2
Secondary Latency Timer = 20h
Memory Base 0 = 0h
Memory Limit 0 = 0h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 0h
I/O Limit 0 = 0h
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 2
PCI Int Pin = INT B
Interrupt line = 10
Bridge Control = 740h
Subsystem Vendor ID = e11h
Subsystem ID = b0c3h
Legacy Mode Base Address = 3e0h
System Control = 41020h
Retry Status = 0h
Card Control = 0h
Device Control = 74h
Buffer Control = 0h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 11 0e c3 b0 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 20 10 04 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 74 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Display (VGA)
Vendor ID = 10c8h, Neomagic Corporation
Device ID = 4h, NM2160 MagicGraph 128XD
PCI index = 0h
Class Codes = 030000h
Revision ID = 0h
Bus number = 0
Device number = 18
Function num = 0
Status Reg = 280h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 80h
Cache Line Size= 0h
PCI Mem Address = fd000000h prefetchable 32bit length 16777216 enabled
PCI Mem Address = fea00000h 32bit length 2097152 enabled
PCI Mem Address = fed00000h 32bit length 1048576 enabled
Max Lat = 255ns
Min Gnt = 16ns
PCI Int Pin = INT A
Interrupt line = 11
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Mass Storage (IDE)
Vendor ID = 1045h, OPTi Inc.
Device ID = d568h, 82C825 PCI bus master IDE controller
PCI index = 0h
Class Codes = 010180h
Revision ID = 30h
Bus number = 0
Device number = 20
Function num = 0
Status Reg = 280h
Command Reg = 1h
I/O space access enabled
Memory space access disabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
PCI IO Address = fcf0h length 16 enabled
Subsystem Vendor ID = e11h
Subsystem ID = b0c2h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 20 00 16 00 00 00 00 fa 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Network (Ethernet)
Vendor ID = 13d1h, Abocom Systems Inc
Device ID = ab02h, Unknown Unknown
PCI index = 0h
Class Codes = 020000h
Revision ID = 11h
Bus number = 1
Device number = 0
Function num = 0
Status Reg = 290h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
PCI IO Address = 500h length 256 enabled
PCI Mem Address = ffee0000h 32bit length 1024 enabled
CardBus CIS Pointer = 202h
Subsystem Vendor ID = 13d1h
Subsystem ID = ab02h
PCI Expansion ROM = ffec0000h length 131072 disabled
Max Lat = 255ns
Min Gnt = 255ns
PCI Int Pin = INT A
Interrupt line = 10
Capabilities Pointer = c0h
Capability ID = 1h
Capabilities = fe02h - 0h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 17 13 81 09 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 01 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

\

ifconfig en0

en0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 10.1.2.34 netmask 0xfffffc00 broadcast 10.1.3.255

\

io-net -v -dtulip verbose=3 -ptcpip

tulip CLI Arguments: verbose=3 multicast=true
tulip: scanning for Vendor=0x1011 Device=0x0002
tulip: scanning for Vendor=0x1011 Device=0x0008
tulip: scanning for Vendor=0x1011 Device=0x0009
tulip: scanning for Vendor=0x1011 Device=0x0014
tulip: scanning for Vendor=0x1011 Device=0x0019
tulip: scanning for Vendor=0x8086 Device=0x0039
tulip: scanning for Vendor=0x11ad Device=0x0002
tulip: scanning for Vendor=0x11ad Device=0x0168
tulip: scanning for Vendor=0x1317 Device=0x0985
tulip: scanning for Vendor=0x1317 Device=0x0981
tulip: scanning for Vendor=0x10d9 Device=0x0531
tulip: scanning for Vendor=0x115d Device=0x0003
tulip: scanning for Vendor=0x13d1 Device=0xab02
tulip: RegisterDeviceInstance(nic=0x8056a54, ion=0x8055780)
tulip Hardware Config: Vendor=0x13d1 Device=0xab02 chipset=2500
tulip: host memory, rx/tx Packets & Descriptors allocated rx=32 tx=20
Attempting MII Detection
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
LinkSense : Failure
AutoDetection Completed
Default Media Selected : MII
Media Selected : MII No Link
Tulip: Abocom FE2500
Vendor … 0x13d1
Device … 0xab02
Revision … 0x0
I/O port base … 0x500
Interrupt … 0xa
MAC address … 00e098 963841
tulip: advertise to io-net Vendor 0x13d1 Device 0xab02 Chipset 2500
tulip: advertise to io-net Vendor 0x13d1 Device 0xab02 Chipset 2500
tulip: advertise to io-net Vendor 0x13d1 Device 0xab02 Chipset 2500
tulip (Net: 0): Link Down, Check Cabling
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)

…[preceeding message suppressed, repeated 63 times]…

\

ping 10.1.2.34 [my own IP addr]

PING 10.3.200.163 (10.3.200.163): 56 data bytes
64 bytes from 10.3.200.163: icmp_seq=0 ttl=255 time=1 ms
64 bytes from 10.3.200.163: icmp_seq=1 ttl=255 time=0 ms
64 bytes from 10.3.200.163: icmp_seq=2 ttl=255 time=0 ms
64 bytes from 10.3.200.163: icmp_seq=3 ttl=255 time=0 ms
64 bytes from 10.3.200.163: icmp_seq=4 ttl=255 time=0 ms

— 10.1.2.34 ping statistics —
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 0/0/1 ms

\

ping 10.1.0.1 [my local gateway]

PING 10.1.0.1 (10.1.0.1): 56 data bytes
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1

— 10.1.0.1 ping statistics —
5 packets transmitted, 0 packets received, 100% packet loss

Thanks,

Alex Senkevitch

Alexander_Senkevitch · November 21, 2001, 2:24am

I have the additional information and command output you requested. The exact excerpt from the /etc/system/enum/devices/net file is as follows (the numbers indicate line numbers):

83: device(cardbus, ven=13d1, dev=ab02) [line added by me]
84: device(cardbus, ven=1011, dev=0019) [the remainder was original to the file]
85: tag(devn)
86: append(legacy, “,nonet”)
87: requires($(IONET_CMD),)
88: uniq(netnum, devn-en, 0)
89: # assume cardbus only have one ethernet card for now so en0 is always used
90: # mount(-Tio-net “-opci=$(index)” /lib/dll/devn-tulip.so, “/dev/io-net/en$(netnum)”)
91: mount(-Tio-net “-opci=$(index)” /lib/dll/devn-tulip.so, “/dev/io-net/en0”)
92: use(symbolic=netmgr)

The output of the command ‘pidin ar’ is as follows:

pid Arguments
1 procnto
2 /sbin/tinit -p
3 slogger
12292 mqueue
5 pci-bios
6 devb-eide blk auto=partition dos exec=all cam quiet eide dma,ioport=0x1f0,irq=14 eide dma,ioport=0x170,irq=15
7 devc-con -n4
8 fs-pkg -a/pkgs/base/safe-config/etc/system/package/packages
4105 pipe
40970 enum-devices -c/etc/system/enum/common -i. -I~ -I.bak -ebootdev -Elegacy neednet,$(legacy) -E=D bus=none
45067 devc-pty -n 32
90124 io-net -ptcpip -ppppmgr -pqnet
73741 devp-pccard
73742 enum-pccard
147471 random -t
110608 devc-ser8250 -u1 3f8,4
159761 dumper -d /var/dumps
110610 devb-fdc cam quiet blk auto=partition,cache=100k
552979 pterm
426004 pwm
221205 Photon -g -lphlogin “-Sphshutdown -l”
266262 fontsleuth -d /usr/photon/font_repository
471063 shelf
258072 /usr/photon/bin/phfontFA -d /usr/photon/font_repository -j -s 300k
299033 io-graphics -g800x600x16 -dldevg-neomagic.so -I0 -d0x10c8,0x4
315418 /usr/photon/bin/devi-hirun kbd fd -d/dev/kbd ps2 mousedev
552987 /bin/sh
507932 bkgdmgr
507933 wmswitch
507934 saver
659487 pidin ar

If you need anything else, don’t hesitate to ask. Thanks.

Alex

“Hardware Support Account” <hw@qnx.com> wrote in message news:9tedr2$996$2@nntp.qnx.com…

Hi Alexander,

How are you starting the driver? Have you tried starting the driver manually?
What is the output of pidin ar?

(Thanks for the other output as well).

Erick.

Alexander_Senkevitch · November 26, 2001, 3:48pm

Any ideas?

Thanks.

Alex

“Hardware Support Account” <hw@qnx.com> wrote in message
news:9tedr2$996$2@nntp.qnx.com…

Hi Alexander,

How are you starting the driver? Have you tried starting the driver
manually?
What is the output of pidin ar?

(Thanks for the other output as well).

Erick.

Alexander Senkevitch <> asenkevitch@hotmail.com> > wrote:

I have a Compaq Presario 1621 laptop with CardBus slots and a SMC 8035
(Abocom FE2500 series dongleless) CardBus 10/100 PC Card. I have been

having a heck of a time getting it to function at all. In fact, I have yet
to be able to send ANY traffic across my network connection successfully.
Until VERY recently, enum-pccard would not enumerate my adapter until I
“hacked” the /etc/system/enum/devices/net file with an entry that was
configured for the proper dev/ven id’s and bus topology. Now, at least wh

en my system boots, I get a /dev/io-net/en0 device generated. I have
plugged this card into both a LinkSys 8-port 10/100 autosense switch, AND a

3COM 5-port 10/100 autosense hub, both capable of full duplex, but neither
have been successful. I have swapped out patch cables, and of course, I
always verify that I am getting signal across (link lights, etc). The NIC
itself always lights up with LINK, 100, FULL, PWR; which establish that the
NIC is getting power, that it is running at 100Full Duplex, and th

at it has Link connectivity with the switch/hub.

Hardware specifics:
Notebook: Presario 1621
Chipset: TI PCI1131 Dual Socket CardBus
NIC: SMC 8035TX
Model#: SMC8035TX
P/N: 99-012055-000

I have included output for the following commands:
pin
pin cis
pin config
pci -vvvv
ifconfig en0
io-net -v -dtulip verbose=3 -ptcpip
2 ping’s

ANY input that could be provided would be GREAT! Thanks, this problem
has been persisting for about 2.5 months now. I’m currently using RTP 6.1.0

(original GA dist. from ISO image from Aug.).

This bugs me because the SMC 8035 is listed as a supported NIC, what am
I missing?

Outputs:

pin

Sock Func Type Flags PID Base Size IRQ
1 0 Network C—I-±–X–SAW 73742 0x500 256 10
0xffee0000 1024
1 Empty ----MF---------- None
2 Empty ----MF---------- None
2 Empty ----MF---------- None

\

pin cis

Socket : 1 - Function : 0
Link Target : ‘CIS’
Manufacturer ID : 0x13d1 0xab02
PC Card function : Network LAN Adapter
POST : 0x1
Tuple 0x22 link=2 : 01 02
Tuple 0x22 link=5 : 02 80 96 98 00
Tuple 0x22 link=5 : 02 00 e1 f5 05
Tuple 0x22 link=2 : 03 01
Card tuple version : 5.00
Manufacturer : CardBus
Name of Product : Fast Ethernet
Add’nl info (lot #) : V1.0
Add’nl info (programming):
Tuple 0x04 link=6 : 03 01 2a 00 00 00
Tuple 0x07 link=6 : 11 00 00 01 00 00
Tuple 0x07 link=6 : 02 00 00 01 00 00
Tuple 0x07 link=6 : 07 00 00 02 00 00
Tuple 0x05 link=10 : 41 39 01 b5 1e 02 b0 fc
: fe 84
Link Target : ‘CIS’
Manufacturer ID : 0x13d1 0xab02
PC Card function : Network LAN Adapter
POST : 0x1
Tuple 0x22 link=2 : 01 02
Tuple 0x22 link=5 : 02 80 96 98 00
Tuple 0x22 link=5 : 02 00 e1 f5 05
Tuple 0x22 link=2 : 03 01
Card tuple version : 5.00
Manufacturer : CardBus
Name of Product : Fast Ethernet
Add’nl info (lot #) : V1.0
Add’nl info (programming):
Tuple 0x04 link=6 : 03 01 2a 00 00 00
Tuple 0x07 link=6 : 11 00 00 01 00 00
Tuple 0x07 link=6 : 02 00 00 01 00 00
Tuple 0x07 link=6 : 07 00 00 02 00 00
Tuple 0x05 link=10 : 41 39 01 b5 1e 02 b0 fc
: fe 84

\

pin config

; socket 1
[device]
manufacturer = “CardBus”
product = “Fast Ethernet”
info1 = “V1.0”
info2 = “”
manufacturer = “CardBus”
product = “Fast Ethernet”
info1 = “V1.0”
info2 = “”
register = 0, 0x40, 0x40 ; level mode interrupts

\

pci -vvvv

PCI version = 2.10

Class = Bridge (Host/PCI)
Vendor ID = 1045h, OPTi Inc.
Device ID = c701h, 82C700 FireStar mobile chipset: host bridge
PCI index = 0h
Class Codes = 060000h
Revision ID = 32h
Bus number = 0
Device number = 0
Function num = 0
Status Reg = 280h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 02 20 71 32 00 84 30 00 00 00 5a 06 00 00
0x50: 00 00 00 00 40 c1 00 fc 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 f8 00 00 80 00 00 00 00

Class = Bridge (PCI/ISA)
Vendor ID = 1045h, OPTi Inc.
Device ID = c700h, 82C700 FireStar chipset, PCI-ISA bridge???
PCI index = 0h
Class Codes = 060100h
Revision ID = 31h
Bus number = 0
Device number = 1
Function num = 0
Status Reg = 280h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 02 c0 00 00 06 00 30 0a 30 3f 00 00 40 60
0x50: 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 f1 03 00 20 c0 00 00 00 00 00 00 00
0x70: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 20 00 00 4a 3e
0x90: 00 00 00 29 22 2b 21 00 00 3f 41 24 23 2a 2b 2b
0xA0: 00 00 00 00 00 00 00 00 80 41 dc 35 00 00 01 05
0xB0: 03 04 05 06 07 09 0a 0b 00 0b 01 00 01 00 00 00
0xC0: 10 32 50 76 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 7f 00 00 00 80 0f
0xE0: 00 00 00 00 00 00 00 00 0c 00 f0 e8 f0 e0 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac15h, PCI1131 Dual Socket PCI CardBus Controller
PCI index = 0h
Class Codes = 060700h
Revision ID = 1h
Bus number = 0
Device number = 10
Function num = 0
Status Reg = 200h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
ExCA Base Address = ffeff000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 1
Subordinate Bus Number = 1
Secondary Latency Timer = 20h
Memory Base 0 = ffec0000h
Memory Limit 0 = ffee0000h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 500h
I/O Limit 0 = 5fch
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 10
Bridge Control = 700h
Subsystem Vendor ID = e11h
Subsystem ID = b0c3h
Legacy Mode Base Address = 3e0h
System Control = 243020h
Retry Status = 0h
Card Control = 30h
Device Control = 74h
Buffer Control = 0h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 11 0e c3 b0 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 20 30 24 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 30 74 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac15h, PCI1131 Dual Socket PCI CardBus Controller
PCI index = 1h
Class Codes = 060700h
Revision ID = 1h
Bus number = 0
Device number = 10
Function num = 1
Status Reg = 200h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
ExCA Base Address = ffefe000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 2
Subordinate Bus Number = 2
Secondary Latency Timer = 20h
Memory Base 0 = 0h
Memory Limit 0 = 0h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 0h
I/O Limit 0 = 0h
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 2
PCI Int Pin = INT B
Interrupt line = 10
Bridge Control = 740h
Subsystem Vendor ID = e11h
Subsystem ID = b0c3h
Legacy Mode Base Address = 3e0h
System Control = 41020h
Retry Status = 0h
Card Control = 0h
Device Control = 74h
Buffer Control = 0h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 11 0e c3 b0 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 20 10 04 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 74 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Display (VGA)
Vendor ID = 10c8h, Neomagic Corporation
Device ID = 4h, NM2160 MagicGraph 128XD
PCI index = 0h
Class Codes = 030000h
Revision ID = 0h
Bus number = 0
Device number = 18
Function num = 0
Status Reg = 280h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 80h
Cache Line Size= 0h
PCI Mem Address = fd000000h prefetchable 32bit length 16777216 enabled
PCI Mem Address = fea00000h 32bit length 2097152 enabled
PCI Mem Address = fed00000h 32bit length 1048576 enabled
Max Lat = 255ns
Min Gnt = 16ns
PCI Int Pin = INT A
Interrupt line = 11
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Mass Storage (IDE)
Vendor ID = 1045h, OPTi Inc.
Device ID = d568h, 82C825 PCI bus master IDE controller
PCI index = 0h
Class Codes = 010180h
Revision ID = 30h
Bus number = 0
Device number = 20
Function num = 0
Status Reg = 280h
Command Reg = 1h
I/O space access enabled
Memory space access disabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
PCI IO Address = fcf0h length 16 enabled
Subsystem Vendor ID = e11h
Subsystem ID = b0c2h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 20 00 16 00 00 00 00 fa 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Network (Ethernet)
Vendor ID = 13d1h, Abocom Systems Inc
Device ID = ab02h, Unknown Unknown
PCI index = 0h
Class Codes = 020000h
Revision ID = 11h
Bus number = 1
Device number = 0
Function num = 0
Status Reg = 290h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
PCI IO Address = 500h length 256 enabled
PCI Mem Address = ffee0000h 32bit length 1024 enabled
CardBus CIS Pointer = 202h
Subsystem Vendor ID = 13d1h
Subsystem ID = ab02h
PCI Expansion ROM = ffec0000h length 131072 disabled
Max Lat = 255ns
Min Gnt = 255ns
PCI Int Pin = INT A
Interrupt line = 10
Capabilities Pointer = c0h
Capability ID = 1h
Capabilities = fe02h - 0h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 17 13 81 09 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 01 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

\

ifconfig en0

en0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 10.1.2.34 netmask 0xfffffc00 broadcast 10.1.3.255

\

io-net -v -dtulip verbose=3 -ptcpip

tulip CLI Arguments: verbose=3 multicast=true
tulip: scanning for Vendor=0x1011 Device=0x0002
tulip: scanning for Vendor=0x1011 Device=0x0008
tulip: scanning for Vendor=0x1011 Device=0x0009
tulip: scanning for Vendor=0x1011 Device=0x0014
tulip: scanning for Vendor=0x1011 Device=0x0019
tulip: scanning for Vendor=0x8086 Device=0x0039
tulip: scanning for Vendor=0x11ad Device=0x0002
tulip: scanning for Vendor=0x11ad Device=0x0168
tulip: scanning for Vendor=0x1317 Device=0x0985
tulip: scanning for Vendor=0x1317 Device=0x0981
tulip: scanning for Vendor=0x10d9 Device=0x0531
tulip: scanning for Vendor=0x115d Device=0x0003
tulip: scanning for Vendor=0x13d1 Device=0xab02
tulip: RegisterDeviceInstance(nic=0x8056a54, ion=0x8055780)
tulip Hardware Config: Vendor=0x13d1 Device=0xab02 chipset=2500
tulip: host memory, rx/tx Packets & Descriptors allocated rx=32 tx=20
Attempting MII Detection
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)
LinkSense : Failure
AutoDetection Completed
Default Media Selected : MII
Media Selected : MII No Link
Tulip: Abocom FE2500
Vendor … 0x13d1
Device … 0xab02
Revision … 0x0
I/O port base … 0x500
Interrupt … 0xa
MAC address … 00e098 963841
tulip: advertise to io-net Vendor 0x13d1 Device 0xab02 Chipset 2500
tulip: advertise to io-net Vendor 0x13d1 Device 0xab02 Chipset 2500
tulip: advertise to io-net Vendor 0x13d1 Device 0xab02 Chipset 2500
tulip (Net: 0): Link Down, Check Cabling
tulip_devctl(hdl 0x8056a54, nic 0x8056a54, dcmd 1184629771)

…[preceeding message suppressed, repeated 63 times]…

\

ping 10.1.2.34 [my own IP addr]

PING 10.3.200.163 (10.3.200.163): 56 data bytes
64 bytes from 10.3.200.163: icmp_seq=0 ttl=255 time=1 ms
64 bytes from 10.3.200.163: icmp_seq=1 ttl=255 time=0 ms
64 bytes from 10.3.200.163: icmp_seq=2 ttl=255 time=0 ms
64 bytes from 10.3.200.163: icmp_seq=3 ttl=255 time=0 ms
64 bytes from 10.3.200.163: icmp_seq=4 ttl=255 time=0 ms

— 10.1.2.34 ping statistics —
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 0/0/1 ms

\

ping 10.1.0.1 [my local gateway]

PING 10.1.0.1 (10.1.0.1): 56 data bytes
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 10.1.0.1 64 chars, ret=-1

— 10.1.0.1 ping statistics —
5 packets transmitted, 0 packets received, 100% packet loss

Thanks,

Alex Senkevitch