G450 -> G400

QNX Newsgroups (Archives) qdn.public.qnx4.photon
1

Hi Joe and Erick,

Thanks for your input. I could get the G450 card started by commenting
out the matbios.trap line, but because the resolution is very low, I
downgraded to a Matrox G400. This card should work as I have a second
machine that works at 600x800 with the Pg.matroxdc driver. However for
some reason that I do not understand I still get the freeze when probing
for video modes or when doing a

crttrap trap

Since the machine that works is quite similar in configuration, I
thought that this might have something to do with BIOS settings, but
they seem very similar in both cases, at least as far as I can tell.
Would you have any suggestions? I include the hardware config of the
machine that works (node1) and the one that does not work (node4) as
well as the output of show_pci for both machines. Photon is 1.14 and QNX
4.25, May 2001 release.Thanks in advance, Fabrizio.

node1

motherboard: Asus P3V4X

graphic card: Matrox Millenium II G400 Maxx (dual head, but I use only
one monitor)

node4

motherboard: MSI 694D Pro (2 processor installed, I plan to upgrade to
QNX 6 asap)

graphic card: Matrox Millenium II G400 (single head)

output of show_pci on node1

PCI version = 2.10

Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ d800h
PCI Int Pin = NC
Interrupt line = 0

Class = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9055h,
PCI index = 0h
IO @ d000h MEM @ e0000000h
PCI Int Pin = INT A
Interrupt line = 11

Class = Display (VGA)
Vendor ID = 102bh, Matrox
Device ID = 525h,
PCI index = 0h
MEM @ e2000000h MEM @ e1000000h MEM @ e0800000h ROM @
e1ff00
disabled
PCI Int Pin = INT A
Interrupt line = 11

output of show_pci on node4

PCI version = 2.10

Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ d000h
PCI Int Pin = NC
Interrupt line = no connection

Class = Multimedia (Audio)
Vendor ID = 1106h, VIA Technologies
Device ID = 3058h,
PCI index = 0h
IO @ dc00h IO @ e000h IO @ e400h
PCI Int Pin = INT C
Interrupt line = 10

Class = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9200h,
PCI index = 0h
IO @ ec00h MEM @ da000000h
PCI Int Pin = INT A
Interrupt line = 11

Class = Display (VGA)
Vendor ID = 102bh, Matrox
Device ID = 525h,
PCI index = 0h
MEM @ d4000000h MEM @ d6000000h MEM @ d7000000h
PCI Int Pin = INT A
Interrupt line = 11

2

Hi Fabrizio,

Can you run the grafxscript found at www.geocities.com/erickemuis/files/hardware_scripts/
on your system and send me the tar file that is generates. This script will probe
your machine for graphics information.

Regards,

Joe

Fabrizio Gabbiani <gabbiani@bcm.tmc.edu> wrote:

Hi Joe and Erick,

Thanks for your input. I could get the G450 card started by commenting
out the matbios.trap line, but because the resolution is very low, I
downgraded to a Matrox G400. This card should work as I have a second
machine that works at 600x800 with the Pg.matroxdc driver. However for
some reason that I do not understand I still get the freeze when probing
for video modes or when doing a

crttrap trap

Since the machine that works is quite similar in configuration, I
thought that this might have something to do with BIOS settings, but
they seem very similar in both cases, at least as far as I can tell.
Would you have any suggestions? I include the hardware config of the
machine that works (node1) and the one that does not work (node4) as
well as the output of show_pci for both machines. Photon is 1.14 and QNX
4.25, May 2001 release.Thanks in advance, Fabrizio.

node1

motherboard: Asus P3V4X

graphic card: Matrox Millenium II G400 Maxx (dual head, but I use only
one monitor)

node4

motherboard: MSI 694D Pro (2 processor installed, I plan to upgrade to
QNX 6 asap)

graphic card: Matrox Millenium II G400 (single head)

output of show_pci on node1

PCI version = 2.10

Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ d800h
PCI Int Pin = NC
Interrupt line = 0

Class = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9055h,
PCI index = 0h
IO @ d000h MEM @ e0000000h
PCI Int Pin = INT A
Interrupt line = 11

Class = Display (VGA)
Vendor ID = 102bh, Matrox
Device ID = 525h,
PCI index = 0h
MEM @ e2000000h MEM @ e1000000h MEM @ e0800000h ROM @
e1ff00
disabled
PCI Int Pin = INT A
Interrupt line = 11

output of show_pci on node4

PCI version = 2.10

Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ d000h
PCI Int Pin = NC
Interrupt line = no connection

Class = Multimedia (Audio)
Vendor ID = 1106h, VIA Technologies
Device ID = 3058h,
PCI index = 0h
IO @ dc00h IO @ e000h IO @ e400h
PCI Int Pin = INT C
Interrupt line = 10

Class = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9200h,
PCI index = 0h
IO @ ec00h MEM @ da000000h
PCI Int Pin = INT A
Interrupt line = 11

Class = Display (VGA)
Vendor ID = 102bh, Matrox
Device ID = 525h,
PCI index = 0h
MEM @ d4000000h MEM @ d6000000h MEM @ d7000000h
PCI Int Pin = INT A
Interrupt line = 11

3

Hi Frabrizio,

Oops…that is the RTP graphics script :slight_smile:
www.geocities.com/erickemuis/files/photon is the correct URL for QNX4.

Note: Ensure to make the file executable before running the script.

Regards,

Joe

Hardware Support Account <hw@qnx.com> wrote:

Hi Fabrizio,

Can you run the grafxscript found at > www.geocities.com/erickemuis/files/hardware_scripts/
on your system and send me the tar file that is generates. This script will probe
your machine for graphics information.

Regards,

Joe

Fabrizio Gabbiani <> gabbiani@bcm.tmc.edu> > wrote:

Hi Joe and Erick,

Thanks for your input. I could get the G450 card started by commenting
out the matbios.trap line, but because the resolution is very low, I
downgraded to a Matrox G400. This card should work as I have a second
machine that works at 600x800 with the Pg.matroxdc driver. However for
some reason that I do not understand I still get the freeze when probing
for video modes or when doing a

crttrap trap

Since the machine that works is quite similar in configuration, I
thought that this might have something to do with BIOS settings, but
they seem very similar in both cases, at least as far as I can tell.
Would you have any suggestions? I include the hardware config of the
machine that works (node1) and the one that does not work (node4) as
well as the output of show_pci for both machines. Photon is 1.14 and QNX
4.25, May 2001 release.Thanks in advance, Fabrizio.

node1

motherboard: Asus P3V4X

graphic card: Matrox Millenium II G400 Maxx (dual head, but I use only
one monitor)

node4

motherboard: MSI 694D Pro (2 processor installed, I plan to upgrade to
QNX 6 asap)

graphic card: Matrox Millenium II G400 (single head)

output of show_pci on node1

PCI version = 2.10

Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ d800h
PCI Int Pin = NC
Interrupt line = 0

Class = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9055h,
PCI index = 0h
IO @ d000h MEM @ e0000000h
PCI Int Pin = INT A
Interrupt line = 11

Class = Display (VGA)
Vendor ID = 102bh, Matrox
Device ID = 525h,
PCI index = 0h
MEM @ e2000000h MEM @ e1000000h MEM @ e0800000h ROM @
e1ff00
disabled
PCI Int Pin = INT A
Interrupt line = 11

output of show_pci on node4

PCI version = 2.10

Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ d000h
PCI Int Pin = NC
Interrupt line = no connection

Class = Multimedia (Audio)
Vendor ID = 1106h, VIA Technologies
Device ID = 3058h,
PCI index = 0h
IO @ dc00h IO @ e000h IO @ e400h
PCI Int Pin = INT C
Interrupt line = 10

Class = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9200h,
PCI index = 0h
IO @ ec00h MEM @ da000000h
PCI Int Pin = INT A
Interrupt line = 11

Class = Display (VGA)
Vendor ID = 102bh, Matrox
Device ID = 525h,
PCI index = 0h
MEM @ d4000000h MEM @ d6000000h MEM @ d7000000h
PCI Int Pin = INT A
Interrupt line = 11

4

Hi Joe,

It look like the page

www.geocities.com/erickemuis/files/photon


does not exist any more and I could not find anything on grafxscript at
geocities. Would you have updated info or could you post the file
somewhere I can grab it?

Thanks in advance, Fabrizio.


Hardware Support Account wrote:

Hi Frabrizio,

Oops…that is the RTP graphics script > :slight_smile:
www.geocities.com/erickemuis/files/photon > is the correct URL for QNX4.

Note: Ensure to make the file executable before running the script.

Regards,

Joe

Hardware Support Account <> hw@qnx.com> > wrote:

Hi Fabrizio,


Can you run the grafxscript found at > www.geocities.com/erickemuis/files/hardware_scripts/
on your system and send me the tar file that is generates. This script will probe
your machine for graphics information.


Regards,


Joe


Fabrizio Gabbiani <> gabbiani@bcm.tmc.edu> > wrote:


Hi Joe and Erick,


Thanks for your input. I could get the G450 card started by commenting
out the matbios.trap line, but because the resolution is very low, I
downgraded to a Matrox G400. This card should work as I have a second
machine that works at 600x800 with the Pg.matroxdc driver. However for
some reason that I do not understand I still get the freeze when probing
for video modes or when doing a


crttrap trap


Since the machine that works is quite similar in configuration, I
thought that this might have something to do with BIOS settings, but
they seem very similar in both cases, at least as far as I can tell.
Would you have any suggestions? I include the hardware config of the
machine that works (node1) and the one that does not work (node4) as
well as the output of show_pci for both machines. Photon is 1.14 and QNX
4.25, May 2001 release.Thanks in advance, Fabrizio.


node1



motherboard: Asus P3V4X


graphic card: Matrox Millenium II G400 Maxx (dual head, but I use only
one monitor)


node4



motherboard: MSI 694D Pro (2 processor installed, I plan to upgrade to
QNX 6 asap)


graphic card: Matrox Millenium II G400 (single head)


output of show_pci on node1



PCI version = 2.10


Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ d800h
PCI Int Pin = NC
Interrupt line = 0


Class = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9055h,
PCI index = 0h
IO @ d000h MEM @ e0000000h
PCI Int Pin = INT A
Interrupt line = 11


Class = Display (VGA)
Vendor ID = 102bh, Matrox
Device ID = 525h,
PCI index = 0h
MEM @ e2000000h MEM @ e1000000h MEM @ e0800000h ROM @
e1ff00
disabled
PCI Int Pin = INT A
Interrupt line = 11


output of show_pci on node4



PCI version = 2.10


Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ d000h
PCI Int Pin = NC
Interrupt line = no connection


Class = Multimedia (Audio)
Vendor ID = 1106h, VIA Technologies
Device ID = 3058h,
PCI index = 0h
IO @ dc00h IO @ e000h IO @ e400h
PCI Int Pin = INT C
Interrupt line = 10


Class = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9200h,
PCI index = 0h
IO @ ec00h MEM @ da000000h
PCI Int Pin = INT A
Interrupt line = 11


Class = Display (VGA)
Vendor ID = 102bh, Matrox
Device ID = 525h,
PCI index = 0h
MEM @ d4000000h MEM @ d6000000h MEM @ d7000000h
PCI Int Pin = INT A
Interrupt line = 11

5

Hi Fabrizio,

Try

www.geocities.com/erickmuis/files/photon (note spelling on the name,
not erick=e=muis but erickmuis.

Sigh… the horrible spelling of my name continues :wink: ha!

E.


Fabrizio Gabbiani <gabbiani@bcm.tmc.edu> wrote:

Hi Joe,

It look like the page

www.geocities.com/erickemuis/files/photon



does not exist any more and I could not find anything on grafxscript at
geocities. Would you have updated info or could you post the file
somewhere I can grab it?

Thanks in advance, Fabrizio.



Hardware Support Account wrote:

Hi Frabrizio,

Oops…that is the RTP graphics script > :slight_smile:
www.geocities.com/erickemuis/files/photon > is the correct URL for QNX4.

Note: Ensure to make the file executable before running the script.

Regards,

Joe

Hardware Support Account <> hw@qnx.com> > wrote:

Hi Fabrizio,


Can you run the grafxscript found at > www.geocities.com/erickemuis/files/hardware_scripts/
on your system and send me the tar file that is generates. This script will probe
your machine for graphics information.


Regards,


Joe


Fabrizio Gabbiani <> gabbiani@bcm.tmc.edu> > wrote:


Hi Joe and Erick,


Thanks for your input. I could get the G450 card started by commenting
out the matbios.trap line, but because the resolution is very low, I
downgraded to a Matrox G400. This card should work as I have a second
machine that works at 600x800 with the Pg.matroxdc driver. However for
some reason that I do not understand I still get the freeze when probing
for video modes or when doing a


crttrap trap


Since the machine that works is quite similar in configuration, I
thought that this might have something to do with BIOS settings, but
they seem very similar in both cases, at least as far as I can tell.
Would you have any suggestions? I include the hardware config of the
machine that works (node1) and the one that does not work (node4) as
well as the output of show_pci for both machines. Photon is 1.14 and QNX
4.25, May 2001 release.Thanks in advance, Fabrizio.


node1



motherboard: Asus P3V4X


graphic card: Matrox Millenium II G400 Maxx (dual head, but I use only
one monitor)


node4



motherboard: MSI 694D Pro (2 processor installed, I plan to upgrade to
QNX 6 asap)


graphic card: Matrox Millenium II G400 (single head)


output of show_pci on node1



PCI version = 2.10


Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ d800h
PCI Int Pin = NC
Interrupt line = 0


Class = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9055h,
PCI index = 0h
IO @ d000h MEM @ e0000000h
PCI Int Pin = INT A
Interrupt line = 11


Class = Display (VGA)
Vendor ID = 102bh, Matrox
Device ID = 525h,
PCI index = 0h
MEM @ e2000000h MEM @ e1000000h MEM @ e0800000h ROM @
e1ff00
disabled
PCI Int Pin = INT A
Interrupt line = 11


output of show_pci on node4



PCI version = 2.10


Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ d000h
PCI Int Pin = NC
Interrupt line = no connection


Class = Multimedia (Audio)
Vendor ID = 1106h, VIA Technologies
Device ID = 3058h,
PCI index = 0h
IO @ dc00h IO @ e000h IO @ e400h
PCI Int Pin = INT C
Interrupt line = 10


Class = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9200h,
PCI index = 0h
IO @ ec00h MEM @ da000000h
PCI Int Pin = INT A
Interrupt line = 11


Class = Display (VGA)
Vendor ID = 102bh, Matrox
Device ID = 525h,
PCI index = 0h
MEM @ d4000000h MEM @ d6000000h MEM @ d7000000h
PCI Int Pin = INT A
Interrupt line = 11

6

Hi Erik,


Thanks, I include the graphics info on the machine that does not work
(node4) as well as the one that works (node1), just in case.

I am curious to know what the problem is.

Best wishes, Fabrizio.


Hardware Support Account wrote:

Hi Fabrizio,

Try

www.geocities.com/erickmuis/files/photon > (note spelling on the name,
not erick=e=muis but erickmuis.

Sigh… the horrible spelling of my name continues > :wink: > ha!

E.


Fabrizio Gabbiani <> gabbiani@bcm.tmc.edu> > wrote:


Hi Joe,


It look like the page


www.geocities.com/erickemuis/files/photon



does not exist any more and I could not find anything on grafxscript at
geocities. Would you have updated info or could you post the file
somewhere I can grab it?


Thanks in advance, Fabrizio.



Hardware Support Account wrote:


Hi Frabrizio,

Oops…that is the RTP graphics script > :slight_smile:
www.geocities.com/erickemuis/files/photon > is the correct URL for QNX4.

Note: Ensure to make the file executable before running the script.

Regards,

Joe

Hardware Support Account <> hw@qnx.com> > wrote:


Hi Fabrizio,


Can you run the grafxscript found at > www.geocities.com/erickemuis/files/hardware_scripts/
on your system and send me the tar file that is generates. This script will probe
your machine for graphics information.


Regards,


Joe


Fabrizio Gabbiani <> gabbiani@bcm.tmc.edu> > wrote:


Hi Joe and Erick,


Thanks for your input. I could get the G450 card started by commenting
out the matbios.trap line, but because the resolution is very low, I
downgraded to a Matrox G400. This card should work as I have a second
machine that works at 600x800 with the Pg.matroxdc driver. However for
some reason that I do not understand I still get the freeze when probing
for video modes or when doing a


crttrap trap


Since the machine that works is quite similar in configuration, I
thought that this might have something to do with BIOS settings, but
they seem very similar in both cases, at least as far as I can tell.
Would you have any suggestions? I include the hardware config of the
machine that works (node1) and the one that does not work (node4) as
well as the output of show_pci for both machines. Photon is 1.14 and QNX
4.25, May 2001 release.Thanks in advance, Fabrizio.


node1



motherboard: Asus P3V4X


graphic card: Matrox Millenium II G400 Maxx (dual head, but I use only
one monitor)


node4



motherboard: MSI 694D Pro (2 processor installed, I plan to upgrade to
QNX 6 asap)


graphic card: Matrox Millenium II G400 (single head)


output of show_pci on node1



PCI version = 2.10


Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ d800h
PCI Int Pin = NC
Interrupt line = 0


Class = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9055h,
PCI index = 0h
IO @ d000h MEM @ e0000000h
PCI Int Pin = INT A
Interrupt line = 11


Class = Display (VGA)
Vendor ID = 102bh, Matrox
Device ID = 525h,
PCI index = 0h
MEM @ e2000000h MEM @ e1000000h MEM @ e0800000h ROM @
e1ff00
disabled
PCI Int Pin = INT A
Interrupt line = 11


output of show_pci on node4



PCI version = 2.10


Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ d000h
PCI Int Pin = NC
Interrupt line = no connection


Class = Multimedia (Audio)
Vendor ID = 1106h, VIA Technologies
Device ID = 3058h,
PCI index = 0h
IO @ dc00h IO @ e000h IO @ e400h
PCI Int Pin = INT C
Interrupt line = 10


Class = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9200h,
PCI index = 0h
IO @ ec00h MEM @ da000000h
PCI Int Pin = INT A
Interrupt line = 11


Class = Display (VGA)
Vendor ID = 102bh, Matrox
Device ID = 525h,
PCI index = 0h
MEM @ d4000000h MEM @ d6000000h MEM @ d7000000h
PCI Int Pin = INT A
Interrupt line = 11
\

7

Hi Erik,

It tried

crttrap -FMatroxG trap

and that worked. Thanks. Fabrizio

Hardware Support Account wrote:

Hi Fabrizio,

Try

www.geocities.com/erickmuis/files/photon > (note spelling on the name,
not erick=e=muis but erickmuis.

Sigh… the horrible spelling of my name continues > :wink: > ha!

E.


Fabrizio Gabbiani <> gabbiani@bcm.tmc.edu> > wrote:


Hi Joe,


It look like the page


www.geocities.com/erickemuis/files/photon



does not exist any more and I could not find anything on grafxscript at
geocities. Would you have updated info or could you post the file
somewhere I can grab it?


Thanks in advance, Fabrizio.



Hardware Support Account wrote:


Hi Frabrizio,

Oops…that is the RTP graphics script > :slight_smile:
www.geocities.com/erickemuis/files/photon > is the correct URL for QNX4.

Note: Ensure to make the file executable before running the script.

Regards,

Joe

Hardware Support Account <> hw@qnx.com> > wrote:


Hi Fabrizio,


Can you run the grafxscript found at > www.geocities.com/erickemuis/files/hardware_scripts/
on your system and send me the tar file that is generates. This script will probe
your machine for graphics information.


Regards,


Joe


Fabrizio Gabbiani <> gabbiani@bcm.tmc.edu> > wrote:


Hi Joe and Erick,


Thanks for your input. I could get the G450 card started by commenting
out the matbios.trap line, but because the resolution is very low, I
downgraded to a Matrox G400. This card should work as I have a second
machine that works at 600x800 with the Pg.matroxdc driver. However for
some reason that I do not understand I still get the freeze when probing
for video modes or when doing a


crttrap trap


Since the machine that works is quite similar in configuration, I
thought that this might have something to do with BIOS settings, but
they seem very similar in both cases, at least as far as I can tell.
Would you have any suggestions? I include the hardware config of the
machine that works (node1) and the one that does not work (node4) as
well as the output of show_pci for both machines. Photon is 1.14 and QNX
4.25, May 2001 release.Thanks in advance, Fabrizio.


node1



motherboard: Asus P3V4X


graphic card: Matrox Millenium II G400 Maxx (dual head, but I use only
one monitor)


node4



motherboard: MSI 694D Pro (2 processor installed, I plan to upgrade to
QNX 6 asap)


graphic card: Matrox Millenium II G400 (single head)


output of show_pci on node1



PCI version = 2.10


Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ d800h
PCI Int Pin = NC
Interrupt line = 0


Class = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9055h,
PCI index = 0h
IO @ d000h MEM @ e0000000h
PCI Int Pin = INT A
Interrupt line = 11


Class = Display (VGA)
Vendor ID = 102bh, Matrox
Device ID = 525h,
PCI index = 0h
MEM @ e2000000h MEM @ e1000000h MEM @ e0800000h ROM @
e1ff00
disabled
PCI Int Pin = INT A
Interrupt line = 11


output of show_pci on node4



PCI version = 2.10


Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ d000h
PCI Int Pin = NC
Interrupt line = no connection


Class = Multimedia (Audio)
Vendor ID = 1106h, VIA Technologies
Device ID = 3058h,
PCI index = 0h
IO @ dc00h IO @ e000h IO @ e400h
PCI Int Pin = INT C
Interrupt line = 10


Class = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9200h,
PCI index = 0h
IO @ ec00h MEM @ da000000h
PCI Int Pin = INT A
Interrupt line = 11


Class = Display (VGA)
Vendor ID = 102bh, Matrox
Device ID = 525h,
PCI index = 0h
MEM @ d4000000h MEM @ d6000000h MEM @ d7000000h
PCI Int Pin = INT A
Interrupt line = 11
\