Compaq EVO N600 + Intel PRO100 VM network problem

Hi,

I have just installed QNX PE 6.2.1 to my portable computer with intel pro 100 VM net device.
But I receive the following message at boot: “Unable to allocate resource: invalid argument” and after booting I can not use the networking. Network device is not presented under /dev/io-net/, but the card is listed at the pci devices (pci -v) with deviceid 1038h. If I slay and restart io-net with: io-net -d speedo did=0x1038 -p tcpip I receive: “unable to init dll devn-speedo: No such device” error.

Could somebody help me?

Can you post the ethernet block from the pci -v output?

Please find the the asked output :

Class = Network (Ethernet)
Vendor ID = 8086h, Intel Corporation
Device ID = 1038h, 82559 Networking device
PCI index = 0h
Class Codes = 020000h
Revision ID = 41h
Bus number = 2
Device number = 8
Function num = 0
Status Reg = 290h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 42h
Cache Line Size= 8h un-cacheable
PCI Mem Address = 40100000h 32bit length 4096 enabled
PCI IO Address = 2800h length 64 enabled
Subsystem Vendor ID = e11h
Subsystem ID = 98h
Max Lat = 56ns
Min Gnt = 8ns
PCI Int Pin = INT A
Interrupt line = 11
Capabilities Pointer = dch
Capability ID = 1h
Capabilities = fe22h - 3a004100h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 22 fe
0xE0: 00 41 00 3a 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Try doing this…

slay -f io-net
io-net -d speedo verbose=10,vid=0x8086,did=0x1038 -p tcpip

And if you get the no device error, check the output from sloginfo and post it here.