I ordered a 3c905 card and got delivered a 3c905cx. Needless to say, I can’t
make it work under QNX 4.25D. Net.ether905 just quits with no message at
all. Before I send the NIC back, is there any prospect of this card working
under QNX4? (Or is it the normal 3com trick of changing the last letter and
changing the whole chipset at the same time??)
Julian Thornhill
Previously, Julian Thornhill wrote in qdn.public.qnx4:
I ordered a 3c905 card and got delivered a 3c905cx. Needless to say, I can’t
make it work under QNX 4.25D. Net.ether905 just quits with no message at
all. Before I send the NIC back, is there any prospect of this card working
under QNX4? (Or is it the normal 3com trick of changing the last letter and
changing the whole chipset at the same time??)
No, don’t send it back! Please post the output from ‘show_pci -v’. We do
support the 905C, but maybe 3Com have changed the device ID.
Julian Thornhill
\
–
Hugh Brown (613) 591-0931 ext. 209 (voice)
QNX Software Systems Ltd. (613) 591-3579 (fax)
175 Terence Matthews Cres. email: hsbrown@qnx.com
Kanata, Ontario, Canada.
K2M 1W8
Hugh Brown <hsbrown@qnx.com> wrote in article
<Voyager.010209132148.2072I@node90.ott.qnx.com>…
Previously, Julian Thornhill wrote in qdn.public.qnx4:
I ordered a 3c905 card and got delivered a 3c905cx. Needless to say, I
can’t
make it work under QNX 4.25D. Net.ether905 just quits with no message
at
all. Before I send the NIC back, is there any prospect of this card
working
under QNX4? (Or is it the normal 3com trick of changing the last letter
and
changing the whole chipset at the same time??)
No, don’t send it back! Please post the output from ‘show_pci -v’. We do
support the 905C, but maybe 3Com have changed the device ID.OK - you asked for it >
There is also a NE2000 clone pci NIC fitted, just to get some network
connectivity going. The 3com card would not work even before this was
fitted.
Results of show_pci -v (results of show_pci without -v at bottom)
PCI version = 2.10
Vendor ID = 1106h, VIA Technologies
Device ID = 691h,
PCI index = 0h
Class Code = 060000h Bridge (Host/PCI) ProgIF=0
Revision ID = 44h
Bus number = 0
Device number = 0
Function num = 0
Status Reg = 2210h
Command Reg = 6h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Base Address = MEM@d0000000h,Prefetchable,32bit length 67108864
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = 0
PCI Int Pin = NC
Interrupt line = 0
Vendor ID = 1106h, VIA Technologies
Device ID = 8598h,
PCI index = 0h
Class Code = 060400h Bridge (PCI/PCI) ProgIF=0
Revision ID = 0h
Bus number = 0
Device number = 1
Function num = 0
Status Reg = 2230h
Command Reg = 7h
Header type = 1h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Primary Bus Number = 0h
Secondary Bus Number = 1h
Subordinate Bus Number = 1h
Secondary Latency Timer = 0h
I/O Base = d0h
I/O Limit = d0h
Secondary Status = 0h
Memory Base = d400h
Memory Limit = d7f0h
Prefetchable Memory Base = fff0h
Prefetchable Memory Limit= 0h
Prefetchable Base Upper 32 Bits = 0h
Prefetchable Limit Upper 32 Bits = 0h
I/O Base Upper 16 Bits = 0h
I/O Limit Upper 16 Bits = 0h
Bridge Control = 0ns
PCI Int Pin = 0
PCI Int Pin = NC
Interrupt line = 0
Expansion ROM = 80h length -2147483648 disabled
Vendor ID = 1106h, VIA Technologies
Device ID = 596h,
PCI index = 0h
Class Code = 060100h Bridge (PCI/ISA) ProgIF=0
Revision ID = 23h
Bus number = 0
Device number = 2
Function num = 0
Status Reg = 200h
Command Reg = 87h
Header type = 0h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = 0
PCI Int Pin = NC
Interrupt line = 0
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
Class Code = 01018ah Mass Storage (IDE) ProgIF=138
Revision ID = 10h
Bus number = 0
Device number = 2
Function num = 1
Status Reg = 290h
Command Reg = 7h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
IO@e000h length 16 bytes
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = 0
PCI Int Pin = NC
Interrupt line = no connection
Vendor ID = 1106h, VIA Technologies
Device ID = 3038h,
PCI index = 0h
Class Code = 0c0300h Serial Bus (Universal Serial Bus) ProgIF=0
Revision ID = 11h
Bus number = 0
Device number = 2
Function num = 2
Status Reg = 210h
Command Reg = 7h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 8h un-cacheable
IO@e400h length 32 bytes
Subsystem Vendor ID = 925h
Subsystem ID = 1234h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = 4
PCI Int Pin = INT D
Interrupt line = 9
Vendor ID = 1106h, VIA Technologies
Device ID = 3050h,
PCI index = 0h
Class Code = 060000h Bridge (Host/PCI) ProgIF=0
Revision ID = 30h
Bus number = 0
Device number = 2
Function num = 3
Status Reg = 280h
Command Reg = 0h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = 0
PCI Int Pin = NC
Interrupt line = 0
Vendor ID = 10b7h, 3Com
Device ID = 9200h,
PCI index = 0h
Class Code = 020000h Network (Ethernet) ProgIF=0
Revision ID = 78h
Bus number = 0
Device number = 15
Function num = 0
Status Reg = 210h
Command Reg = 7h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 8h un-cacheable
Base Address = IO@e800h length 128 bytes MEM@d9000000h,32bit length 128
Subsystem Vendor ID = 10b7h
Subsystem ID = 1000h
Max Lat = 10ns
Min Gnt = 10ns
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 10
Vendor ID = 10ech,
Device ID = 8029h,
PCI index = 0h
Class Code = 020000h Network (Ethernet) ProgIF=0
Revision ID = 0h
Bus number = 0
Device number = 18
Function num = 0
Status Reg = 200h
Command Reg = 3h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Base Address = IO@ec00h length 32 bytes
Subsystem Vendor ID = 10ech
Subsystem ID = 8029h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 11
Vendor ID = 1002h, ATI TECHNOLOGIES INC
Device ID = 4c4dh,
PCI index = 0h
Class Code = 030000h Display (VGA) ProgIF=0
Revision ID = 64h
Bus number = 1
Device number = 0
Function num = 0
Status Reg = 290h
Command Reg = 87h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 8h un-cacheable
Base Address = MEM@d4000000h,32bit length 16777216 IO@d000h length 256
bytes MEM@d6000000h,32bit length 4096
Subsystem Vendor ID = 1002h
Subsystem ID = 4c4dh
Max Lat = 0ns
Min Gnt = 8ns
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 5
IRQ Routing = bus=0 slot=1 device=14
No card configured in slot
INTA=3,4,5,7,9,10,11,12,14,15 Slot2:INTD Slot3:INTB
Slot4:INTA Slot5:INTC Slot6:INTC Motherboard:INTB
INTB=3,4,5,7,9,10,11,12,14,15 Slot2:INTA Slot3:INTC
Slot4:INTB Slot5:INTD Slot6:INTD Motherboard:INTC Motherboard:INTC
INTC=3,4,5,7,9,10,11,12,14,15 Slot2:INTB Slot3:INTD
Slot4:INTC Slot5:INTA Slot6:INTA Motherboard:INTD Motherboard:INTD
INTD=3,4,5,7,9,10,11,12,14,15 Slot2:INTC Slot3:INTA
Slot4:INTD Slot5:INTB Slot6:INTB Motherboard:INTA
IRQ Routing = bus=0 slot=2 device=15
Vendor ID = 10b7h, 3Com
Device ID = 9200h,
INTA=3,4,5,7,9,10,11,12,14,15 Slot1:INTB Slot3:INTC
Slot4:INTB Slot5:INTD Slot6:INTD Motherboard:INTC Motherboard:INTC
INTB=3,4,5,7,9,10,11,12,14,15 Slot1:INTC Slot3:INTD
Slot4:INTC Slot5:INTA Slot6:INTA Motherboard:INTD Motherboard:INTD
INTC=3,4,5,7,9,10,11,12,14,15 Slot1:INTD Slot3:INTA
Slot4:INTD Slot5:INTB Slot6:INTB Motherboard:INTA
INTD=3,4,5,7,9,10,11,12,14,15 Slot1:INTA Slot3:INTB
Slot4:INTA Slot5:INTC Slot6:INTC Motherboard:INTB
IRQ Routing = bus=0 slot=3 device=17
No card configured in slot
INTA=3,4,5,7,9,10,11,12,14,15 Slot1:INTD Slot2:INTC
Slot4:INTD Slot5:INTB Slot6:INTB Motherboard:INTA
INTB=3,4,5,7,9,10,11,12,14,15 Slot1:INTA Slot2:INTD
Slot4:INTA Slot5:INTC Slot6:INTC Motherboard:INTB
INTC=3,4,5,7,9,10,11,12,14,15 Slot1:INTB Slot2:INTA
Slot4:INTB Slot5:INTD Slot6:INTD Motherboard:INTC Motherboard:INTC
INTD=3,4,5,7,9,10,11,12,14,15 Slot1:INTC Slot2:INTB
Slot4:INTC Slot5:INTA Slot6:INTA Motherboard:INTD Motherboard:INTD
IRQ Routing = bus=0 slot=4 device=18
Vendor ID = 10ech,
Device ID = 8029h,
INTA=3,4,5,7,9,10,11,12,14,15 Slot1:INTA Slot2:INTD
Slot3:INTB Slot5:INTC Slot6:INTC Motherboard:INTB
INTB=3,4,5,7,9,10,11,12,14,15 Slot1:INTB Slot2:INTA
Slot3:INTC Slot5:INTD Slot6:INTD Motherboard:INTC Motherboard:INTC
INTC=3,4,5,7,9,10,11,12,14,15 Slot1:INTC Slot2:INTB
Slot3:INTD Slot5:INTA Slot6:INTA Motherboard:INTD Motherboard:INTD
INTD=3,4,5,7,9,10,11,12,14,15 Slot1:INTD Slot2:INTC
Slot3:INTA Slot5:INTB Slot6:INTB Motherboard:INTA
IRQ Routing = bus=0 slot=5 device=16
No card configured in slot
INTA=3,4,5,7,9,10,11,12,14,15 Slot1:INTC Slot2:INTB
Slot3:INTD Slot4:INTC Slot6:INTA Motherboard:INTD Motherboard:INTD
INTB=3,4,5,7,9,10,11,12,14,15 Slot1:INTD Slot2:INTC
Slot3:INTA Slot4:INTD Slot6:INTB Motherboard:INTA
INTC=3,4,5,7,9,10,11,12,14,15 Slot1:INTA Slot2:INTD
Slot3:INTB Slot4:INTA Slot6:INTC Motherboard:INTB
INTD=3,4,5,7,9,10,11,12,14,15 Slot1:INTB Slot2:INTA
Slot3:INTC Slot4:INTB Slot6:INTD Motherboard:INTC Motherboard:INTC
IRQ Routing = bus=0 slot=6 device=12
No card configured in slot
INTA=3,4,5,7,9,10,11,12,14,15 Slot1:INTC Slot2:INTB
Slot3:INTD Slot4:INTC Slot5:INTA Motherboard:INTD Motherboard:INTD
INTB=3,4,5,7,9,10,11,12,14,15 Slot1:INTD Slot2:INTC
Slot3:INTA Slot4:INTD Slot5:INTB Motherboard:INTA
INTC=3,4,5,7,9,10,11,12,14,15 Slot1:INTA Slot2:INTD
Slot3:INTB Slot4:INTA Slot5:INTC Motherboard:INTB
INTD=3,4,5,7,9,10,11,12,14,15 Slot1:INTB Slot2:INTA
Slot3:INTC Slot4:INTB Slot5:INTD Motherboard:INTC Motherboard:INTC
IRQ Routing = bus=0 motherboard device=1
Vendor ID = 1106h, VIA Technologies
Device ID = 8598h,
INTA=3,4,5,7,9,10,11,12,14,15 Slot1:INTD Slot2:INTC
Slot3:INTA Slot4:INTD Slot5:INTB Slot6:INTB
INTB=3,4,5,7,9,10,11,12,14,15 Slot1:INTA Slot2:INTD
Slot3:INTB Slot4:INTA Slot5:INTC Slot6:INTC
INTC=3,4,5,7,9,10,11,12,14,15 Slot1:INTB Slot2:INTA
Slot3:INTC Slot4:INTB Slot5:INTD Slot6:INTD Motherboard:INTC
INTD=3,4,5,7,9,10,11,12,14,15 Slot1:INTC Slot2:INTB
Slot3:INTD Slot4:INTC Slot5:INTA Slot6:INTA Motherboard:INTD
IRQ Routing = bus=0 motherboard device=2
Vendor ID = 1106h, VIA Technologies
Device ID = 596h,
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
Vendor ID = 1106h, VIA Technologies
Device ID = 3038h,
Vendor ID = 1106h, VIA Technologies
Device ID = 3050h,
INTC=3,4,5,7,9,10,11,12,14,15 Slot1:INTB Slot2:INTA Slot3:INTC Slot4:INTB
Slot5:INTD Slot6:INTD Motherboard:INTC
INTD=3,4,5,7,9,10,11,12,14,15 Slot1:INTC Slot2:INTB
Slot3:INTD Slot4:INTC Slot5:INTA Slot6:INTA Motherboard:INTD
**Results of show_pci ***
PCI version = 2.10
Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ e000h
PCI Int Pin = NC
Interrupt line = no connection
Class = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9200h,
PCI index = 0h
IO @ e800h MEM @ d9000000h
PCI Int Pin = INT A
Interrupt line = 10
Class = Network (Ethernet)
Vendor ID = 10ech,
Device ID = 8029h,
PCI index = 0h
IO @ ec00h
PCI Int Pin = INT A
Interrupt line = 11
Class = Display (VGA)
Vendor ID = 1002h, ATI TECHNOLOGIES INC
Device ID = 4c4dh,
PCI index = 0h
MEM @ d4000000h IO @ d000h MEM @ d6000000h
PCI Int Pin = INT A
Interrupt line = 5
We are using 3com 3C905C-TX-M cards quite extensively for 100Mbps work with QNX
4.25. Not sure of the patch version. Sin ver gives 4.24J Feb 17 2000 as the
driver version. We do however pass explicit -i9 on the command line. Can’t
remember if that is necessary.
I do know that an earlier version didn’t work. If you are still in trouble and
can’t find this version on quiccs, I could send it to you.
Julian Thornhill wrote:
Hugh Brown <> hsbrown@qnx.com> > wrote in article
Voyager.010209132148.2072I@node90.ott.qnx.com> >…
Previously, Julian Thornhill wrote in qdn.public.qnx4:
I ordered a 3c905 card and got delivered a 3c905cx. Needless to say, I
can’t
make it work under QNX 4.25D. Net.ether905 just quits with no message
at
all. Before I send the NIC back, is there any prospect of this card
working
under QNX4? (Or is it the normal 3com trick of changing the last letter
and
changing the whole chipset at the same time??)
No, don’t send it back! Please post the output from ‘show_pci -v’. We do
support the 905C, but maybe 3Com have changed the device ID.OK - you asked for it >
There is also a NE2000 clone pci NIC fitted, just to get some network
connectivity going. The 3com card would not work even before this was
fitted.Results of show_pci -v (results of show_pci without -v at bottom)
PCI version = 2.10
Vendor ID = 1106h, VIA Technologies
Device ID = 691h,
PCI index = 0h
Class Code = 060000h Bridge (Host/PCI) ProgIF=0
Revision ID = 44h
Bus number = 0
Device number = 0
Function num = 0
Status Reg = 2210h
Command Reg = 6h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Base Address = MEM@d0000000h,Prefetchable,32bit length 67108864
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = 0
PCI Int Pin = NC
Interrupt line = 0Vendor ID = 1106h, VIA Technologies
Device ID = 8598h,
PCI index = 0h
Class Code = 060400h Bridge (PCI/PCI) ProgIF=0
Revision ID = 0h
Bus number = 0
Device number = 1
Function num = 0
Status Reg = 2230h
Command Reg = 7h
Header type = 1h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Primary Bus Number = 0h
Secondary Bus Number = 1h
Subordinate Bus Number = 1h
Secondary Latency Timer = 0h
I/O Base = d0h
I/O Limit = d0h
Secondary Status = 0h
Memory Base = d400h
Memory Limit = d7f0h
Prefetchable Memory Base = fff0h
Prefetchable Memory Limit= 0h
Prefetchable Base Upper 32 Bits = 0h
Prefetchable Limit Upper 32 Bits = 0h
I/O Base Upper 16 Bits = 0h
I/O Limit Upper 16 Bits = 0h
Bridge Control = 0ns
PCI Int Pin = 0
PCI Int Pin = NC
Interrupt line = 0Expansion ROM = 80h length -2147483648 disabled
Vendor ID = 1106h, VIA Technologies
Device ID = 596h,
PCI index = 0h
Class Code = 060100h Bridge (PCI/ISA) ProgIF=0
Revision ID = 23h
Bus number = 0
Device number = 2
Function num = 0
Status Reg = 200h
Command Reg = 87h
Header type = 0h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0hMax Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = 0
PCI Int Pin = NC
Interrupt line = 0Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
Class Code = 01018ah Mass Storage (IDE) ProgIF=138
Revision ID = 10h
Bus number = 0
Device number = 2
Function num = 1
Status Reg = 290h
Command Reg = 7h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
IO@e000h length 16 bytes
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = 0
PCI Int Pin = NC
Interrupt line = no connectionVendor ID = 1106h, VIA Technologies
Device ID = 3038h,
PCI index = 0h
Class Code = 0c0300h Serial Bus (Universal Serial Bus) ProgIF=0
Revision ID = 11h
Bus number = 0
Device number = 2
Function num = 2
Status Reg = 210h
Command Reg = 7h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 8h un-cacheable
IO@e400h length 32 bytes
Subsystem Vendor ID = 925h
Subsystem ID = 1234h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = 4
PCI Int Pin = INT D
Interrupt line = 9Vendor ID = 1106h, VIA Technologies
Device ID = 3050h,
PCI index = 0h
Class Code = 060000h Bridge (Host/PCI) ProgIF=0
Revision ID = 30h
Bus number = 0
Device number = 2
Function num = 3
Status Reg = 280h
Command Reg = 0h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0hMax Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = 0
PCI Int Pin = NC
Interrupt line = 0Vendor ID = 10b7h, 3Com
Device ID = 9200h,
PCI index = 0h
Class Code = 020000h Network (Ethernet) ProgIF=0
Revision ID = 78h
Bus number = 0
Device number = 15
Function num = 0
Status Reg = 210h
Command Reg = 7h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 8h un-cacheable
Base Address = IO@e800h length 128 bytes MEM@d9000000h,32bit length 128
Subsystem Vendor ID = 10b7h
Subsystem ID = 1000h
Max Lat = 10ns
Min Gnt = 10ns
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 10Vendor ID = 10ech,
Device ID = 8029h,
PCI index = 0h
Class Code = 020000h Network (Ethernet) ProgIF=0
Revision ID = 0h
Bus number = 0
Device number = 18
Function num = 0
Status Reg = 200h
Command Reg = 3h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Base Address = IO@ec00h length 32 bytes
Subsystem Vendor ID = 10ech
Subsystem ID = 8029h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 11Vendor ID = 1002h, ATI TECHNOLOGIES INC
Device ID = 4c4dh,
PCI index = 0h
Class Code = 030000h Display (VGA) ProgIF=0
Revision ID = 64h
Bus number = 1
Device number = 0
Function num = 0
Status Reg = 290h
Command Reg = 87h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 8h un-cacheable
Base Address = MEM@d4000000h,32bit length 16777216 IO@d000h length 256
bytes MEM@d6000000h,32bit length 4096
Subsystem Vendor ID = 1002h
Subsystem ID = 4c4dh
Max Lat = 0ns
Min Gnt = 8ns
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 5IRQ Routing = bus=0 slot=1 device=14
No card configured in slot
INTA=3,4,5,7,9,10,11,12,14,15 Slot2:INTD Slot3:INTB
Slot4:INTA Slot5:INTC Slot6:INTC Motherboard:INTB
INTB=3,4,5,7,9,10,11,12,14,15 Slot2:INTA Slot3:INTC
Slot4:INTB Slot5:INTD Slot6:INTD Motherboard:INTC Motherboard:INTC
INTC=3,4,5,7,9,10,11,12,14,15 Slot2:INTB Slot3:INTD
Slot4:INTC Slot5:INTA Slot6:INTA Motherboard:INTD Motherboard:INTD
INTD=3,4,5,7,9,10,11,12,14,15 Slot2:INTC Slot3:INTA
Slot4:INTD Slot5:INTB Slot6:INTB Motherboard:INTAIRQ Routing = bus=0 slot=2 device=15
Vendor ID = 10b7h, 3Com
Device ID = 9200h,
INTA=3,4,5,7,9,10,11,12,14,15 Slot1:INTB Slot3:INTC
Slot4:INTB Slot5:INTD Slot6:INTD Motherboard:INTC Motherboard:INTC
INTB=3,4,5,7,9,10,11,12,14,15 Slot1:INTC Slot3:INTD
Slot4:INTC Slot5:INTA Slot6:INTA Motherboard:INTD Motherboard:INTD
INTC=3,4,5,7,9,10,11,12,14,15 Slot1:INTD Slot3:INTA
Slot4:INTD Slot5:INTB Slot6:INTB Motherboard:INTA
INTD=3,4,5,7,9,10,11,12,14,15 Slot1:INTA Slot3:INTB
Slot4:INTA Slot5:INTC Slot6:INTC Motherboard:INTBIRQ Routing = bus=0 slot=3 device=17
No card configured in slot
INTA=3,4,5,7,9,10,11,12,14,15 Slot1:INTD Slot2:INTC
Slot4:INTD Slot5:INTB Slot6:INTB Motherboard:INTA
INTB=3,4,5,7,9,10,11,12,14,15 Slot1:INTA Slot2:INTD
Slot4:INTA Slot5:INTC Slot6:INTC Motherboard:INTB
INTC=3,4,5,7,9,10,11,12,14,15 Slot1:INTB Slot2:INTA
Slot4:INTB Slot5:INTD Slot6:INTD Motherboard:INTC Motherboard:INTC
INTD=3,4,5,7,9,10,11,12,14,15 Slot1:INTC Slot2:INTB
Slot4:INTC Slot5:INTA Slot6:INTA Motherboard:INTD Motherboard:INTDIRQ Routing = bus=0 slot=4 device=18
Vendor ID = 10ech,
Device ID = 8029h,
INTA=3,4,5,7,9,10,11,12,14,15 Slot1:INTA Slot2:INTD
Slot3:INTB Slot5:INTC Slot6:INTC Motherboard:INTB
INTB=3,4,5,7,9,10,11,12,14,15 Slot1:INTB Slot2:INTA
Slot3:INTC Slot5:INTD Slot6:INTD Motherboard:INTC Motherboard:INTC
INTC=3,4,5,7,9,10,11,12,14,15 Slot1:INTC Slot2:INTB
Slot3:INTD Slot5:INTA Slot6:INTA Motherboard:INTD Motherboard:INTD
INTD=3,4,5,7,9,10,11,12,14,15 Slot1:INTD Slot2:INTC
Slot3:INTA Slot5:INTB Slot6:INTB Motherboard:INTAIRQ Routing = bus=0 slot=5 device=16
No card configured in slot
INTA=3,4,5,7,9,10,11,12,14,15 Slot1:INTC Slot2:INTB
Slot3:INTD Slot4:INTC Slot6:INTA Motherboard:INTD Motherboard:INTD
INTB=3,4,5,7,9,10,11,12,14,15 Slot1:INTD Slot2:INTC
Slot3:INTA Slot4:INTD Slot6:INTB Motherboard:INTA
INTC=3,4,5,7,9,10,11,12,14,15 Slot1:INTA Slot2:INTD
Slot3:INTB Slot4:INTA Slot6:INTC Motherboard:INTB
INTD=3,4,5,7,9,10,11,12,14,15 Slot1:INTB Slot2:INTA
Slot3:INTC Slot4:INTB Slot6:INTD Motherboard:INTC Motherboard:INTCIRQ Routing = bus=0 slot=6 device=12
No card configured in slot
INTA=3,4,5,7,9,10,11,12,14,15 Slot1:INTC Slot2:INTB
Slot3:INTD Slot4:INTC Slot5:INTA Motherboard:INTD Motherboard:INTD
INTB=3,4,5,7,9,10,11,12,14,15 Slot1:INTD Slot2:INTC
Slot3:INTA Slot4:INTD Slot5:INTB Motherboard:INTA
INTC=3,4,5,7,9,10,11,12,14,15 Slot1:INTA Slot2:INTD
Slot3:INTB Slot4:INTA Slot5:INTC Motherboard:INTB
INTD=3,4,5,7,9,10,11,12,14,15 Slot1:INTB Slot2:INTA
Slot3:INTC Slot4:INTB Slot5:INTD Motherboard:INTC Motherboard:INTCIRQ Routing = bus=0 motherboard device=1
Vendor ID = 1106h, VIA Technologies
Device ID = 8598h,
INTA=3,4,5,7,9,10,11,12,14,15 Slot1:INTD Slot2:INTC
Slot3:INTA Slot4:INTD Slot5:INTB Slot6:INTB
INTB=3,4,5,7,9,10,11,12,14,15 Slot1:INTA Slot2:INTD
Slot3:INTB Slot4:INTA Slot5:INTC Slot6:INTC
INTC=3,4,5,7,9,10,11,12,14,15 Slot1:INTB Slot2:INTA
Slot3:INTC Slot4:INTB Slot5:INTD Slot6:INTD Motherboard:INTC
INTD=3,4,5,7,9,10,11,12,14,15 Slot1:INTC Slot2:INTB
Slot3:INTD Slot4:INTC Slot5:INTA Slot6:INTA Motherboard:INTDIRQ Routing = bus=0 motherboard device=2
Vendor ID = 1106h, VIA Technologies
Device ID = 596h,
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
Vendor ID = 1106h, VIA Technologies
Device ID = 3038h,
Vendor ID = 1106h, VIA Technologies
Device ID = 3050h,INTC=3,4,5,7,9,10,11,12,14,15 Slot1:INTB Slot2:INTA Slot3:INTC Slot4:INTB
Slot5:INTD Slot6:INTD Motherboard:INTC
INTD=3,4,5,7,9,10,11,12,14,15 Slot1:INTC Slot2:INTB
Slot3:INTD Slot4:INTC Slot5:INTA Slot6:INTA Motherboard:INTD**Results of show_pci ***
PCI version = 2.10
Class = Mass Storage (IDE)
Vendor ID = 1106h, VIA Technologies
Device ID = 571h,
PCI index = 0h
IO @ e000h
PCI Int Pin = NC
Interrupt line = no connectionClass = Network (Ethernet)
Vendor ID = 10b7h, 3Com
Device ID = 9200h,
PCI index = 0h
IO @ e800h MEM @ d9000000h
PCI Int Pin = INT A
Interrupt line = 10Class = Network (Ethernet)
Vendor ID = 10ech,
Device ID = 8029h,
PCI index = 0h
IO @ ec00h
PCI Int Pin = INT A
Interrupt line = 11Class = Display (VGA)
Vendor ID = 1002h, ATI TECHNOLOGIES INC
Device ID = 4c4dh,
PCI index = 0h
MEM @ d4000000h IO @ d000h MEM @ d6000000h
PCI Int Pin = INT A
Interrupt line = 5
Donald Backstrom <donaldb@cstgroup.com.au> wrote in message
news:3A872884.BDCFCB89@cstgroup.com.au…
We are using 3com 3C905C-TX-M cards quite extensively for 100Mbps work
with QNX
4.25. Not sure of the patch version. Sin ver gives 4.24J Feb 17 2000 as
the
driver version. We do however pass explicit -i9 on the command line. Can’t
remember if that is necessary.I do know that an earlier version didn’t work. If you are still in trouble
and
can’t find this version on quiccs, I could send it to you.
Thanks - I’ve made some progress this morning. This was my sequence of
actions:
Installed QNX from December 1999 CD.
Net.ether905 would not find the card.
Installed NE2000 card in addition to 3c905 to get a network running.
Copied QNX 4.25D update from another machine and installed it.
Tried new Net.ether905 which refused to work.
–made first posting to this news group–
Obtained Intel Pro100 NIC and swapped it for the NE2000.
Intel card works fine, BUT 3c905 starts to work!!!
Much card swapping later I determined that the NE2000 cardmade the 3c905
driver fail in some way.
Thus if only 3c905 fitted all would work once the 4.25D update had been
applied - it was the NE2000 card leading me astray.
