Hi all,
I have problems.
when I boot QNX on my laptop. it freeze after this message comes:
devi-hirun kbd fd -d/dev/kbd ps2 kb-2
Can somebody help me?
I installed the QNX on my Desktop it works fine.
Thanks.
Jun
Do you know what type of video chip is in your laptop?
Can you post the output of pci -v ?
There were a number of problems with Toshiba laptops that
contained Chips & Technologies parts.
Jun Xu <jxuhot@hotmail.com> wrote:
Hi all,
I have problems.
when I boot QNX on my laptop. it freeze after this message comes:devi-hirun kbd fd -d/dev/kbd ps2 kb-2
Can somebody help me?
I installed the QNX on my Desktop it works fine.
Thanks.
Jun
Hi,
This is my laptop:
Processor:
166MHz Pentium
MMX Memory:
Ports:
9pin serial,
parallel, mouse, keyboard,
SVGA, PCMCIA, PC
card (ZVport),
microphone &
speaker sockets
Screen:
12.1" colour TFT
SVGA
Floppy drive:
1.44MB 3.5"
(swappable)
Hard disk:
2.16GB
CD-ROM:
Ten speed
(swappable)
Sound:
SoundBlaster Pro
compatible sound system
Provided with:
Integral pointing
device, 110-240v External
Powerpack, Battery
and Carry Case
Thanks
Jun
mvr@qnx.com wrote:
Do you know what type of video chip is in your laptop?
Can you post the output of pci -v ?
There were a number of problems with Toshiba laptops that
contained Chips & Technologies parts.Jun Xu <> jxuhot@hotmail.com> > wrote:
Hi all,I have problems.
when I boot QNX on my laptop. it freeze after this message comes:devi-hirun kbd fd -d/dev/kbd ps2 kb-2
Can somebody help me?
I installed the QNX on my Desktop it works fine.
Thanks.
Jun
Can you post the output of: pci -v (run as root)
Jun Xu : Unitec Engineering <enguic@unitec.ca> wrote:
Hi,
This is my laptop:
Processor:
166MHz Pentium
MMX Memory:
Ports:
9pin serial,
parallel, mouse, keyboard,
SVGA, PCMCIA, PC
card (ZVport),
microphone &
speaker sockets
Screen:
12.1" colour TFT
SVGA
Floppy drive:
1.44MB 3.5"
(swappable)
Hard disk:
2.16GB
CD-ROM:
Ten speed
(swappable)
Sound:
SoundBlaster Pro
compatible sound system
Provided with:
Integral pointing
device, 110-240v External
Powerpack, Battery
and Carry CaseThanks
Junmvr@qnx.com > wrote:
Do you know what type of video chip is in your laptop?
Can you post the output of pci -v ?
There were a number of problems with Toshiba laptops that
contained Chips & Technologies parts.Jun Xu <> jxuhot@hotmail.com> > wrote:
Hi all,I have problems.
when I boot QNX on my laptop. it freeze after this message comes:devi-hirun kbd fd -d/dev/kbd ps2 kb-2
Can somebody help me?
I installed the QNX on my Desktop it works fine.
Thanks.
Jun
here are all I have on the screen after QNX boots and freeze:
Neutrino technology inside!!!
Process #1: 586 with FPU (Pentium/MMX Stepping 4) speed = 165
unable to allocate resource: Resource temproraly unavailable
unable to allocate resource: Resource temproraly unavailable
unable to allocate resource: Resource temproraly unavailable
Press the spacebar to input boot options…
Detected EIDE. Scanning for device
This can take up 30 seconds…
[4102] fs-pkg built: Sep 7 2000 16:00:23
FS-PKG: Open configuration [/etc/system/package/packages]
FS-PKG: Ready to handle requests
Installing /dev/par port 378
file /.swapfile added as swap device
File /.swapfile successfully added as a swap device
mode_init: No such device or address
devi_hirun kbd fd -d/dev/kbd ps2 kb -2
Jun
<mvr@qnx.com> wrote in message news:90j2n9$5ag$1@nntp.qnx.com…
Do you know what type of video chip is in your laptop?
Can you post the output of pci -v ?
There were a number of problems with Toshiba laptops that
contained Chips & Technologies parts.
Jun Xu <> jxuhot@hotmail.com> > wrote:
Hi all,I have problems.
when I boot QNX on my laptop. it freeze after this message comes:devi-hirun kbd fd -d/dev/kbd ps2 kb-2
Can somebody help me?
I installed the QNX on my Desktop it works fine.
Thanks.
Jun
Jun Xu <jxuhot@hotmail.com> wrote:
Press the spacebar to input boot options…
When you get this option press the spacebar and select option 3 to
not start Photon. You should get a login prompt. Login as root and
type pci -v. Post the information here. Thanks
Michael,
My laptop does not stop for the spacebar, it just simply skips this
step,
Press the spacebar to input boot options…
Jun
Michael Van Reenen wrote:
Jun Xu <> jxuhot@hotmail.com> > wrote:
Press the spacebar to input boot options…
When you get this option press the spacebar and select option 3 to
not start Photon. You should get a login prompt. Login as root and
type pci -v. Post the information here. Thanks
I have this:
sh: pci: not found
Jun Xu : Unitec Engineering <enguic@unitec.ca> wrote in message
news:3A369694.BB79A879@unitec.ca…
Michael,
My laptop does not stop for the spacebar, it just simply skips this
step,
Press the spacebar to input boot options…Jun
Michael Van Reenen wrote:Jun Xu <> jxuhot@hotmail.com> > wrote:
Press the spacebar to input boot options…
When you get this option press the spacebar and select option 3 to
not start Photon. You should get a login prompt. Login as root and
type pci -v. Post the information here. Thanks
I have this
sh: pci: not found
Michael Van Reenen <mvr@qnx.com> wrote in message
news:912qdf$cfb$1@nntp.qnx.com…
Jun Xu <> jxuhot@hotmail.com> > wrote:
Press the spacebar to input boot options…
When you get this option press the spacebar and select option 3 to
not start Photon. You should get a login prompt. Login as root and
type pci -v. Post the information here. Thanks
Login as root
“Jun Xu” <jxuhot@hotmail.com> wrote in message
news:917306$qo0$1@inn.qnx.com…
I have this:
sh: pci: not found
Jun Xu : Unitec Engineering <> enguic@unitec.ca> > wrote in message
news:> 3A369694.BB79A879@unitec.ca> …
Michael,My laptop does not stop for the spacebar, it just simply skips this
step,
Press the spacebar to input boot options…Jun
Michael Van Reenen wrote:Jun Xu <> jxuhot@hotmail.com> > wrote:
Press the spacebar to input boot options…
When you get this option press the spacebar and select option 3 to
not start Photon. You should get a login prompt. Login as root and
type pci -v. Post the information here. Thanks
I try to login as root, but it always says “login increct”!
Mario Charest <mcharest@void_zinformatic.com> wrote in message
news:917sne$ch5$1@nntp.qnx.com…
Login as root
“Jun Xu” <> jxuhot@hotmail.com> > wrote in message
news:917306$qo0$> 1@inn.qnx.com> …
I have this:sh: pci: not found
Jun Xu : Unitec Engineering <> enguic@unitec.ca> > wrote in message
news:> 3A369694.BB79A879@unitec.ca> …
Michael,My laptop does not stop for the spacebar, it just simply skips this
step,
Press the spacebar to input boot options…Jun
Michael Van Reenen wrote:Jun Xu <> jxuhot@hotmail.com> > wrote:
Press the spacebar to input boot options…
When you get this option press the spacebar and select option 3 to
not start Photon. You should get a login prompt. Login as root and
type pci -v. Post the information here. Thanks
\
When you install qrtp you provided a password I assume.
Are you SURE you are using this same password.
If not you may need to reinstall the whole thing (there
are ways around this but it’s probably faster to reinstall
anyway)
\
- Mario
“People looking to serious, should be looking to Sirius”
“Jun Xu” <jxuhot@hotmail.com> wrote in message
news:91c9oo$567$1@inn.qnx.com…
I try to login as root, but it always says “login increct”!
Mario Charest <mcharest@void_zinformatic.com> wrote in message
news:917sne$ch5$> 1@nntp.qnx.com> …
Login as root“Jun Xu” <> jxuhot@hotmail.com> > wrote in message
news:917306$qo0$> 1@inn.qnx.com> …
I have this:sh: pci: not found
Jun Xu : Unitec Engineering <> enguic@unitec.ca> > wrote in message
news:> 3A369694.BB79A879@unitec.ca> …
Michael,My laptop does not stop for the spacebar, it just simply skips this
step,
Press the spacebar to input boot options…Jun
Michael Van Reenen wrote:Jun Xu <> jxuhot@hotmail.com> > wrote:
Press the spacebar to input boot options…
When you get this option press the spacebar and select option 3 to
not start Photon. You should get a login prompt. Login as root
and
type pci -v. Post the information here. Thanks
\
Yes, I reinstalled many times and wrote down the passwords, user names, I
believe I used the right password.
Mario Charest wrote:
When you install qrtp you provided a password I assume.
Are you SURE you are using this same password.If not you may need to reinstall the whole thing (there
are ways around this but it’s probably faster to reinstall
anyway)
- Mario
“People looking to serious, should be looking to Sirius”“Jun Xu” <> jxuhot@hotmail.com> > wrote in message
news:91c9oo$567$> 1@inn.qnx.com> …I try to login as root, but it always says “login increct”!
Mario Charest <mcharest@void_zinformatic.com> wrote in message
news:917sne$ch5$> 1@nntp.qnx.com> …
Login as root“Jun Xu” <> jxuhot@hotmail.com> > wrote in message
news:917306$qo0$> 1@inn.qnx.com> …
I have this:sh: pci: not found
Jun Xu : Unitec Engineering <> enguic@unitec.ca> > wrote in message
news:> 3A369694.BB79A879@unitec.ca> …
Michael,My laptop does not stop for the spacebar, it just simply skips this
step,
Press the spacebar to input boot options…Jun
Michael Van Reenen wrote:Jun Xu <> jxuhot@hotmail.com> > wrote:
Press the spacebar to input boot options…
When you get this option press the spacebar and select option 3 to
not start Photon. You should get a login prompt. Login as root
and
type pci -v. Post the information here. Thanks
\
I installed this version in my Windows 95 (1 partition) desktop, it works
fine.
I really like this RTOS. But I do not understand why it does not on
my laptop! I read the newsgroup, and find there are many problems on Toshiba
Laptop.
Mario Charest <mcharest@void_zinformatic.com> wrote in message
news:91dfhd$ld1$1@nntp.qnx.com…
When you install qrtp you provided a password I assume.
Are you SURE you are using this same password.If not you may need to reinstall the whole thing (there
are ways around this but it’s probably faster to reinstall
anyway)
\
- Mario
“People looking to serious, should be looking to Sirius”“Jun Xu” <> jxuhot@hotmail.com> > wrote in message
news:91c9oo$567$> 1@inn.qnx.com> …I try to login as root, but it always says “login increct”!
Mario Charest <mcharest@void_zinformatic.com> wrote in message
news:917sne$ch5$> 1@nntp.qnx.com> …
Login as root“Jun Xu” <> jxuhot@hotmail.com> > wrote in message
news:917306$qo0$> 1@inn.qnx.com> …
I have this:sh: pci: not found
Jun Xu : Unitec Engineering <> enguic@unitec.ca> > wrote in message
news:> 3A369694.BB79A879@unitec.ca> …
Michael,My laptop does not stop for the spacebar, it just simply skips
this
step,
Press the spacebar to input boot options…Jun
Michael Van Reenen wrote:Jun Xu <> jxuhot@hotmail.com> > wrote:
Press the spacebar to input boot options…
When you get this option press the spacebar and select option 3
to
not start Photon. You should get a login prompt. Login as root
and
type pci -v. Post the information here. Thanks
\
Hi Jun,
There have been a number of issues with Toshiba laptops, these
have been addressed in Patch A which should be out shortly.
We have a feeling that your issues may all be resolved with the
new patch.
Please be patient 
Erick.
Jun Xu <jxuhot@hotmail.com> wrote:
Hi all,
I have problems.
when I boot QNX on my laptop. it freeze after this message comes:devi-hirun kbd fd -d/dev/kbd ps2 kb-2
Can somebody help me?
I installed the QNX on my Desktop it works fine.
Thanks.
Jun