I don’t have a devices tab in Network Cfg and nettrap returns “No network
cards detected”. I tried a 3comm and a Xircomm card. Any ideas?
When I run pin, it detects the card and tells me the irq it is on as well
some other info. Somehow the drivers aren’t being loaded…
Thanks
I have same situation amd have been told that PCMCIA NICs aren’t
currently supported. PCCard ones should work. It is very confusing
because some PCMCIA cards actually have PCCard label on them 
Davin wrote:
I don’t have a devices tab in Network Cfg and nettrap returns “No network
cards detected”. I tried a 3comm and a Xircomm card. Any ideas?When I run pin, it detects the card and tells me the irq it is on as well
some other info. Somehow the drivers aren’t being loaded…Thanks
Hi Davin,
Can you be more specific? What chipsets are on the cards?
Supported hardware can be found here:
http://qdn.qnx.com/support/hardware/platform/pcmcia.html
Erick
Davin <davinsufer@hotmail.com> wrote:
I don’t have a devices tab in Network Cfg and nettrap returns “No network
cards detected”. I tried a 3comm and a Xircomm card. Any ideas?When I run pin, it detects the card and tells me the irq it is on as well
some other info. Somehow the drivers aren’t being loaded…Thanks
The 3com card is the 3CCFE575CT-D, on the supported hardware page I found
the 3CCFE575BT. I would think that these two cards would use the same
chipset. I am able to see the card when I type pin… In technical support
section on QNX there is a description of how to set the card up manually but
it only describes a situation where you know which standard to use (NE2000)
I am not sure what to enter…
Any ideas?
Thanks
“Erick Muis” <emuis@qnx.com> wrote in message
news:93vifr$rrk$1@nntp.qnx.com…
Hi Davin,
Can you be more specific? What chipsets are on the cards?
Supported hardware can be found here:
http://qdn.qnx.com/support/hardware/platform/pcmcia.html
Erick
Davin <> davinsufer@hotmail.com> > wrote:
I don’t have a devices tab in Network Cfg and nettrap returns “No
network
cards detected”. I tried a 3comm and a Xircomm card. Any ideas?When I run pin, it detects the card and tells me the irq it is on as
well
some other info. Somehow the drivers aren’t being loaded…Thanks
Hi,
I have the very same problem. I tried the 3com cards 3CCFE574BT and
3CCFE575CT without any result. Does anyone have any information on this?
Dietmar
“Davin” <davinsufer@hotmail.com> wrote in message
news:946v6b$17b$1@inn.qnx.com…
The 3com card is the 3CCFE575CT-D, on the supported hardware page I found
the 3CCFE575BT. I would think that these two cards would use the same
chipset. I am able to see the card when I type pin… In technical
support
section on QNX there is a description of how to set the card up manually
but
it only describes a situation where you know which standard to use
(NE2000)
I am not sure what to enter…Any ideas?
Thanks
“Erick Muis” <> emuis@qnx.com> > wrote in message
news:93vifr$rrk$> 1@nntp.qnx.com> …
Hi Davin,Can you be more specific? What chipsets are on the cards?
Supported hardware can be found here:
http://qdn.qnx.com/support/hardware/platform/pcmcia.html
Erick
Davin <> davinsufer@hotmail.com> > wrote:
I don’t have a devices tab in Network Cfg and nettrap returns “No
network
cards detected”. I tried a 3comm and a Xircomm card. Any ideas?When I run pin, it detects the card and tells me the irq it is on as
well
some other info. Somehow the drivers aren’t being loaded…Thanks
\
Hi,
did you ever get this resolved?
I have the 3CCFE575CT-D card as well and am unable to get it up and running
on Neutrino.
Any assistance would be appreciated.
P. Randy Aeberhardt
Tantalus Systems Corp.
(604) 299-0458
http://www.tantalus-systems.com
“Dietmar” <drabel@gmx.de> wrote in message news:95so7n$c4d$1@inn.qnx.com…
Hi,
I have the very same problem. I tried the 3com cards 3CCFE574BT and
3CCFE575CT without any result. Does anyone have any information on this?Dietmar
“Davin” <> davinsufer@hotmail.com> > wrote in message
news:946v6b$17b$> 1@inn.qnx.com> …
The 3com card is the 3CCFE575CT-D, on the supported hardware page I
found
the 3CCFE575BT. I would think that these two cards would use the same
chipset. I am able to see the card when I type pin… In technical
support
section on QNX there is a description of how to set the card up manually
but
it only describes a situation where you know which standard to use
(NE2000)
I am not sure what to enter…Any ideas?
Thanks
“Erick Muis” <> emuis@qnx.com> > wrote in message
news:93vifr$rrk$> 1@nntp.qnx.com> …
Hi Davin,Can you be more specific? What chipsets are on the cards?
Supported hardware can be found here:
http://qdn.qnx.com/support/hardware/platform/pcmcia.html
Erick
Davin <> davinsufer@hotmail.com> > wrote:
I don’t have a devices tab in Network Cfg and nettrap returns “No
network
cards detected”. I tried a 3comm and a Xircomm card. Any ideas?When I run pin, it detects the card and tells me the irq it is on as
well
some other info. Somehow the drivers aren’t being loaded…Thanks
\
I too can not get this configuration too work. The devp-pccard service
will not start. The uname command returns the date “2000/10/17-14:59:25
edt” this does not sound correct for the B update that is supposed to be
on the web.
P.S. I used Windows 2000 proffesional to run the qnxrtp.exe installation.
Randy Aeberhardt wrote:
Hi,
did you ever get this resolved?
I have the 3CCFE575CT-D card as well and am unable to get it up and running
on Neutrino.Any assistance would be appreciated.
P. Randy Aeberhardt
Tantalus Systems Corp.
(604) 299-0458
http://www.tantalus-systems.com
“Dietmar” <> drabel@gmx.de> > wrote in message news:95so7n$c4d$> 1@inn.qnx.com> …
Hi,
I have the very same problem. I tried the 3com cards 3CCFE574BT and
3CCFE575CT without any result. Does anyone have any information on this?Dietmar
“Davin” <> davinsufer@hotmail.com> > wrote in message
news:946v6b$17b$> 1@inn.qnx.com> …The 3com card is the 3CCFE575CT-D, on the supported hardware page I
found
the 3CCFE575BT. I would think that these two cards would use the same
chipset. I am able to see the card when I type pin… In technicalsupport
section on QNX there is a description of how to set the card up manually
but
it only describes a situation where you know which standard to use
(NE2000)
I am not sure what to enter…
Any ideas?
Thanks
“Erick Muis” <> emuis@qnx.com> > wrote in message
news:93vifr$rrk$> 1@nntp.qnx.com> …Hi Davin,
Can you be more specific? What chipsets are on the cards?
Supported hardware can be found here:
http://qdn.qnx.com/support/hardware/platform/pcmcia.html
Erick
Davin <> davinsufer@hotmail.com> > wrote:I don’t have a devices tab in Network Cfg and nettrap returns "No
network
cards detected". I tried a 3comm and a Xircomm card. Any ideas?
When I run pin, it detects the card and tells me the irq it is on as
well
some other info. Somehow the drivers aren’t being loaded…
Thanks
There’s a “catch-22” here. You cannot get the B update without your network
working
and in some cases you can’t get your networking to operate without the B
update.
I wish someone at QNX would listen to us and post the ^%$#$# update on the
Web!
Also, the date you uname is returning is correct for the January
distribution (release A).
Go Figure!
Randy Aeberhardt.
paeberhardt@tantalus-systems.com
“Casey Davis” <ddavis2@d3dinc.com> wrote in message
news:3AE8D52A.6030908@d3dinc.com…
I too can not get this configuration too work. The devp-pccard service
will not start. The uname command returns the date “2000/10/17-14:59:25
edt” this does not sound correct for the B update that is supposed to be
on the web.P.S. I used Windows 2000 proffesional to run the qnxrtp.exe installation.
Randy Aeberhardt wrote:
Hi,
did you ever get this resolved?
I have the 3CCFE575CT-D card as well and am unable to get it up and
running
on Neutrino.Any assistance would be appreciated.
P. Randy Aeberhardt
Tantalus Systems Corp.
(604) 299-0458
http://www.tantalus-systems.com
“Dietmar” <> drabel@gmx.de> > wrote in message
news:95so7n$c4d$> 1@inn.qnx.com> …Hi,
I have the very same problem. I tried the 3com cards 3CCFE574BT and
3CCFE575CT without any result. Does anyone have any information on
this?Dietmar
“Davin” <> davinsufer@hotmail.com> > wrote in message
news:946v6b$17b$> 1@inn.qnx.com> …The 3com card is the 3CCFE575CT-D, on the supported hardware page I
found
the 3CCFE575BT. I would think that these two cards would use the same
chipset. I am able to see the card when I type pin… In technicalsupport
section on QNX there is a description of how to set the card up
manuallybut
it only describes a situation where you know which standard to use
(NE2000)
I am not sure what to enter…
Any ideas?
Thanks
“Erick Muis” <> emuis@qnx.com> > wrote in message
news:93vifr$rrk$> 1@nntp.qnx.com> …Hi Davin,
Can you be more specific? What chipsets are on the cards?
Supported hardware can be found here:
http://qdn.qnx.com/support/hardware/platform/pcmcia.html
Erick
Davin <> davinsufer@hotmail.com> > wrote:I don’t have a devices tab in Network Cfg and nettrap returns "No
network
cards detected". I tried a 3comm and a Xircomm card. Any ideas?
When I run pin, it detects the card and tells me the irq it is on as
well
some other info. Somehow the drivers aren’t being loaded…
Thanks
Hi Randy,
We are still looking at this problem, and will post a solution when one is found.
Regards,
Joe
Randy Aeberhardt <raeberhardt@tantalus-systems.com> wrote:
Hi,
did you ever get this resolved?
I have the 3CCFE575CT-D card as well and am unable to get it up and running
on Neutrino.Any assistance would be appreciated.
P. Randy Aeberhardt
Tantalus Systems Corp.
(604) 299-0458
http://www.tantalus-systems.com
“Dietmar” <> drabel@gmx.de> > wrote in message news:95so7n$c4d$> 1@inn.qnx.com> …
Hi,
I have the very same problem. I tried the 3com cards 3CCFE574BT and
3CCFE575CT without any result. Does anyone have any information on this?Dietmar
“Davin” <> davinsufer@hotmail.com> > wrote in message
news:946v6b$17b$> 1@inn.qnx.com> …
The 3com card is the 3CCFE575CT-D, on the supported hardware page I
found
the 3CCFE575BT. I would think that these two cards would use the same
chipset. I am able to see the card when I type pin… In technical
support
section on QNX there is a description of how to set the card up manually
but
it only describes a situation where you know which standard to use
(NE2000)
I am not sure what to enter…Any ideas?
Thanks
“Erick Muis” <> emuis@qnx.com> > wrote in message
news:93vifr$rrk$> 1@nntp.qnx.com> …
Hi Davin,Can you be more specific? What chipsets are on the cards?
Supported hardware can be found here:
http://qdn.qnx.com/support/hardware/platform/pcmcia.html
Erick
Davin <> davinsufer@hotmail.com> > wrote:
I don’t have a devices tab in Network Cfg and nettrap returns “No
network
cards detected”. I tried a 3comm and a Xircomm card. Any ideas?When I run pin, it detects the card and tells me the irq it is on as
well
some other info. Somehow the drivers aren’t being loaded…Thanks
\
Randy Aeberhardt wrote:
There’s a “catch-22” here. You cannot get the B update without your network
working
and in some cases you can’t get your networking to operate without the B
update.I wish someone at QNX would listen to us and post the ^%$#$# update on the
Web!Also, the date you uname is returning is correct for the January
distribution (release A).Go Figure!
Randy Aeberhardt.
paeberhardt@tantalus-systems.com“Casey Davis” <> ddavis2@d3dinc.com> > wrote in message
news:> 3AE8D52A.6030908@d3dinc.com> …I too can not get this configuration too work. The devp-pccard service
will not start. The uname command returns the date “2000/10/17-14:59:25
edt” this does not sound correct for the B update that is supposed to be
on the web.P.S. I used Windows 2000 proffesional to run the qnxrtp.exe installation.
Randy Aeberhardt wrote:
Hi,did you ever get this resolved?
I have the 3CCFE575CT-D card as well and am unable to get it up and
running
on Neutrino.
Any assistance would be appreciated.
P. Randy Aeberhardt
Tantalus Systems Corp.
(604) 299-0458
http://www.tantalus-systems.com
“Dietmar” <> drabel@gmx.de> > wrote in message
news:95so7n$c4d$> 1@inn.qnx.com> …
Hi,
I have the very same problem. I tried the 3com cards 3CCFE574BT and
3CCFE575CT without any result. Does anyone have any information onthis?
Dietmar
“Davin” <> davinsufer@hotmail.com> > wrote in message
news:946v6b$17b$> 1@inn.qnx.com> …
The 3com card is the 3CCFE575CT-D, on the supported hardware page Ifound
the 3CCFE575BT. I would think that these two cards would use the same
chipset. I am able to see the card when I type pin… In technicalsupport
section on QNX there is a description of how to set the card upmanually
but
it only describes a situation where you know which standard to use(NE2000)
I am not sure what to enter…Any ideas?
Thanks
“Erick Muis” <> emuis@qnx.com> > wrote in message
news:93vifr$rrk$> 1@nntp.qnx.com> …
Hi Davin,Can you be more specific? What chipsets are on the cards?
Supported hardware can be found here:
http://qdn.qnx.com/support/hardware/platform/pcmcia.html
Erick
Davin <> davinsufer@hotmail.com> > wrote:
I don’t have a devices tab in Network Cfg and nettrap returns "Nonetwork
cards detected". I tried a 3comm and a Xircomm card. Any ideas?When I run pin, it detects the card and tells me the irq it is on as
well
some other info. Somehow the drivers aren’t being loaded…Thanks
It is posted to the web, look @ tucows qnx site… don’t remeber the url now, look at get.qnx.com ,there is a link there.
/Johan