I have tried to get both Patch A and B running on my Dell Inspiron 8000
notebook without much success.
When I boot, I receive the following 2 errors:
“Unable to allocate resources…”
“No PCMCIA or Cardbus adapters …”
It seems that devp-pccard is just exiting and giving the second message.
As a result, I can’t get my network card to run.
Any ideas?
– Chris
Here is the output from pci -v. I’ve been told this will be useful 
PCI version = 2.10
Class = Bridge (Host/PCI)
Vendor ID = 8086h, Intel Corporation
Device ID = 1130h, 82815 Host-Hub Interface Bridge / DRAM Ctrlr
PCI index = 0h
Class Codes = 060000h
Revision ID = 2h
Bus number = 0
Device number = 0
Function num = 0
Status Reg = 2090h
Command Reg = 106h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Capabilities Pointer = 88h
Capability ID = 9h
Capabilities = f104h - 0h
Capability ID = 2h
Capabilities = 20h - 1f000207h
Class = Bridge (PCI/PCI)
Vendor ID = 8086h, Intel Corporation
Device ID = 1131h, 82815 AGP Bridge
PCI index = 0h
Class Codes = 060400h
Revision ID = 2h
Bus number = 0
Device number = 1
Function num = 0
Status Reg = 20h
Command Reg = 107h
Header type = 1h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
Primary Bus Number = 0h
Secondary Bus Number = 1h
Subordinate Bus Number = 1h
Secondary Latency Timer = 20h
I/O Base = c0h
I/O Limit = c0h
Secondary Status = a2a0h
Memory Base = fc00h
Memory Limit = fdf0h
Prefetchable Memory Base = e800h
Prefetchable Memory Limit= ebf0h
Prefetchable Base Upper 32 Bits = 0h
Prefetchable Limit Upper 32 Bits = 0h
I/O Base Upper 16 Bits = ffffh
I/O Limit Upper 16 Bits = ffffh
Bridge Control = 12ns
PCI Int Pin = NC
Interrupt line = 0
Class = Bridge (PCI/PCI)
Vendor ID = 8086h, Intel Corporation
Device ID = 2448h, Unknown Unknown
PCI index = 0h
Class Codes = 060400h
Revision ID = 3h
Bus number = 0
Device number = 30
Function num = 0
Status Reg = 80h
Command Reg = 107h
Header type = 1h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Primary Bus Number = 0h
Secondary Bus Number = 2h
Subordinate Bus Number = 2h
Secondary Latency Timer = 20h
I/O Base = e0h
I/O Limit = f0h
Secondary Status = 2280h
Memory Base = f400h
Memory Limit = fbf0h
Prefetchable Memory Base = fff0h
Prefetchable Memory Limit= 0h
Prefetchable Base Upper 32 Bits = 0h
Prefetchable Limit Upper 32 Bits = 0h
I/O Base Upper 16 Bits = ffffh
I/O Limit Upper 16 Bits = ffffh
Bridge Control = 6ns
PCI Int Pin = NC
Interrupt line = 0
Class = Bridge (PCI/ISA)
Vendor ID = 8086h, Intel Corporation
Device ID = 244ch, Unknown Unknown
PCI index = 0h
Class Codes = 060100h
Revision ID = 3h
Bus number = 0
Device number = 31
Function num = 0
Status Reg = 280h
Command Reg = 10fh
Header type = 0h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Class = Mass Storage (IDE)
Vendor ID = 8086h, Intel Corporation
Device ID = 244ah, Unknown Unknown
PCI index = 0h
Class Codes = 010180h
Revision ID = 3h
Bus number = 0
Device number = 31
Function num = 1
Status Reg = 280h
Command Reg = 5h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
IO Address = bfa0h length 16 enabled
Subsystem Vendor ID = 8086h
Subsystem ID = 4541h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Class = Serial Bus (Universal Serial Bus)
Vendor ID = 8086h, Intel Corporation
Device ID = 2442h, 82801BA USB Controller
PCI index = 0h
Class Codes = 0c0300h
Revision ID = 3h
Bus number = 0
Device number = 31
Function num = 2
Status Reg = 280h
Command Reg = 5h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
IO Address = dce0h length 32 enabled
Subsystem Vendor ID = 8086h
Subsystem ID = 4541h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = INT D
Interrupt line = 11
Class = Display (VGA)
Vendor ID = 1002h, ATI Technologies
Device ID = 4d46h, Unknown Unknown
PCI index = 0h
Class Codes = 030000h
Revision ID = 0h
Bus number = 1
Device number = 0
Function num = 0
Status Reg = 2b0h
Command Reg = a7h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 8h un-cacheable
Mem Address = e8000000h prefetchable 32bit length 67108864 enabled
IO Address = cc00h length 256 enabled
Mem Address = fcffc000h 32bit length 16384 enabled
Subsystem Vendor ID = 1028h
Subsystem ID = a4h
Max Lat = 0ns
Min Gnt = 8ns
PCI Int Pin = INT A
Interrupt line = 11
Capabilities Pointer = 50h
Capability ID = 2h
Capabilities = 20h - 1f000207h
Capability ID = 1h
Capabilities = 602h - 0h
Class = Multimedia (Audio)
Vendor ID = 125dh, ESS Technology
Device ID = 1998h, ES1980 Maestro-3 PCI Audio Accelerator
PCI index = 0h
Class Codes = 040100h
Revision ID = 10h
Bus number = 2
Device number = 3
Function num = 0
Status Reg = 290h
Command Reg = 7h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
IO Address = ec00h length 256 enabled
Mem Address = f8ffe000h 32bit length 8192 enabled
Subsystem Vendor ID = 1028h
Subsystem ID = a4h
Max Lat = 24ns
Min Gnt = 2ns
PCI Int Pin = INT A
Interrupt line = 5
Capabilities Pointer = c0h
Capability ID = 1h
Capabilities = 7622h - 0h
Class = Communication (Unknown)
Vendor ID = 11c1h, AT&T Microelectronics
Device ID = 448h, LT Winmodem 56k
PCI index = 0h
Class Codes = 078000h
Revision ID = 1h
Bus number = 2
Device number = 6
Function num = 0
Status Reg = 290h
Command Reg = 7h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Mem Address = f8ffdc00h 32bit length 256 enabled
IO Address = e8f8h length 8 enabled
IO Address = e400h length 256 enabled
CardBus CIS Pointer = 40h
Subsystem Vendor ID = 1668h
Subsystem ID = 2000h
Max Lat = 14ns
Min Gnt = 252ns
PCI Int Pin = INT A
Interrupt line = 11
Capabilities Pointer = f8h
Capability ID = 1h
Capabilities = e422h - 0h
Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac42h, PCI4451 PC card CardBus Controller
PCI index = 0h
Class Codes = 060700h
Revision ID = 0h
Bus number = 2
Device number = 15
Function num = 0
Status Reg = 210h
Command Reg = 7h
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 8h un-cacheable
ExCA Base Address = f4000000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 2
Secondary Bus Number = 3
Subordinate Bus Number = 3
Secondary Latency Timer = 20h
Memory Base 0 = 0h
Memory Limit 0 = 0h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 0h
I/O Limit 0 = 0h
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 11
Bridge Control = 7c0h
Subsystem Vendor ID = 1028h
Subsystem ID = a4h
Legacy Mode Base Address = 3e0h
System Control = 3024d020h
Retry Status = c0h
Card Control = 83h
Device Control = 64h
Buffer Control = 60h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac42h, PCI4451 PC card CardBus Controller
PCI index = 1h
Class Codes = 060700h
Revision ID = 0h
Bus number = 2
Device number = 15
Function num = 1
Status Reg = 210h
Command Reg = 7h
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 8h un-cacheable
ExCA Base Address = f4001000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 2
Secondary Bus Number = 4
Subordinate Bus Number = 4
Secondary Latency Timer = 20h
Memory Base 0 = 0h
Memory Limit 0 = 0h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 0h
I/O Limit 0 = 0h
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 11
Bridge Control = 7c0h
Subsystem Vendor ID = 1028h
Subsystem ID = a4h
Legacy Mode Base Address = 3e0h
System Control = 3024d020h
Retry Status = c0h
Card Control = 82h
Device Control = 64h
Buffer Control = 60h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Class = Serial Bus (FireWire)
Vendor ID = 104ch, Texas Instruments
Device ID = 8027h, Unknown Unknown
PCI index = 0h
Class Codes = 0c0010h
Revision ID = 0h
Bus number = 2
Device number = 15
Function num = 2
Status Reg = 210h
Command Reg = 116h
Header type = 0h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 8h un-cacheable
Mem Address = f8ffd000h 32bit length 2048 enabled
Mem Address = f8ff8000h 32bit length 16384 enabled
Subsystem Vendor ID = 1028h
Subsystem ID = a4h
Max Lat = 4ns
Min Gnt = 2ns
PCI Int Pin = INT A
Interrupt line = 11
Capabilities Pointer = 44h
Capability ID = 1h
Capabilities = 6412h - 0h
“Chris Thomas” <cdthomas@sympatico.ca> wrote in message
news:9grkjt$d8o$1@inn.qnx.com…
I have tried to get both Patch A and B running on my Dell Inspiron 8000
notebook without much success.When I boot, I receive the following 2 errors:
“Unable to allocate resources…”
“No PCMCIA or Cardbus adapters …”It seems that devp-pccard is just exiting and giving the second message.
As a result, I can’t get my network card to run.
Any ideas?
– Chris
Hi Chris,
Support for this chipset was only added to the latest devp-pccard which
is currently in beta.
Regards,
Joe
Chris Thomas <cdthomas@sympatico.ca> wrote:
I have tried to get both Patch A and B running on my Dell Inspiron 8000
notebook without much success.When I boot, I receive the following 2 errors:
“Unable to allocate resources…”
“No PCMCIA or Cardbus adapters …”It seems that devp-pccard is just exiting and giving the second message.
As a result, I can’t get my network card to run.
Any ideas?
– Chris
Is that patch C (beta)?
– Chris
“Hardware Support Account” <hw@qnx.com> wrote in message
news:9gvou4$jl1$1@nntp.qnx.com…
Hi Chris,
Support for this chipset was only added to the latest devp-pccard which
is currently in beta.Regards,
Joe
Chris Thomas <> cdthomas@sympatico.ca> > wrote:
I have tried to get both Patch A and B running on my Dell Inspiron 8000
notebook without much success.When I boot, I receive the following 2 errors:
“Unable to allocate resources…”
“No PCMCIA or Cardbus adapters …”It seems that devp-pccard is just exiting and giving the second message.
As a result, I can’t get my network card to run.
Any ideas?
– Chris
Hi Chris,
Actually Patch C is no longer beta and is now released.
This update is in the RTP 6.1.0 Beta.
Regards,
Joe
Chris Thomas <cdthomas@sympatico.ca> wrote:
Is that patch C (beta)?
– Chris
“Hardware Support Account” <> hw@qnx.com> > wrote in message
news:9gvou4$jl1$> 1@nntp.qnx.com> …
Hi Chris,Support for this chipset was only added to the latest devp-pccard which
is currently in beta.Regards,
Joe
Chris Thomas <> cdthomas@sympatico.ca> > wrote:
I have tried to get both Patch A and B running on my Dell Inspiron 8000
notebook without much success.When I boot, I receive the following 2 errors:
“Unable to allocate resources…”
“No PCMCIA or Cardbus adapters …”It seems that devp-pccard is just exiting and giving the second message.
As a result, I can’t get my network card to run.
Any ideas?
– Chris