Mouse problems

Robert_Craig1 · July 8, 2001, 6:21pm

After upgrading to 6.1, I’ve found that my PS-2 Logitech wireless mouse
(which used to work under 6.0) no longer works. I’ve seen the “disable
legascy USB” note in QDN for the BIOS, but my BIOS has no such option
(it’s a Tyan Trinity board). Any other suggestions would be
appreciated!

Thanks
Robert Craig.

Chip_Nayak · July 8, 2001, 8:07pm

I have a similar problem with ps-2 mouse on my laptop. However,
disconnecting and re-connecting the mouse brings it back to life.
This happens only after upgrading to 6.1.

Thanks.
Best regards.
– chip

“Robert Craig” <rcraig@sympatico.ca> wrote in message
news:3B48A490.4A5216D9@sympatico.ca…

After upgrading to 6.1, I’ve found that my PS-2 Logitech wireless mouse
(which used to work under 6.0) no longer works. I’ve seen the “disable
legascy USB” note in QDN for the BIOS, but my BIOS has no such option
(it’s a Tyan Trinity board). Any other suggestions would be
appreciated!

Thanks
Robert Craig.

Hardware_Support_Acc · July 9, 2001, 1:59pm

It sounds like the legacy problem. The devi-hirun driver had a change
made to it that resets the PS2 port when “corrupted” data is received.
This corrupted data is caused by the legacy USB setup in the bios.

Off the top of my head I can’t think of a workaround, however I
will see what I can find out.

Erick.

Chip Nayak <chipnayak@yahoo.com> wrote:

I have a similar problem with ps-2 mouse on my laptop. However,
disconnecting and re-connecting the mouse brings it back to life.
This happens only after upgrading to 6.1.

Thanks.
Best regards.
– chip

“Robert Craig” <> rcraig@sympatico.ca> > wrote in message
news:> 3B48A490.4A5216D9@sympatico.ca> …
After upgrading to 6.1, I’ve found that my PS-2 Logitech wireless mouse
(which used to work under 6.0) no longer works. I’ve seen the “disable
legascy USB” note in QDN for the BIOS, but my BIOS has no such option
(it’s a Tyan Trinity board). Any other suggestions would be
appreciated!

Thanks
Robert Craig.

Robert_Craig1 · July 11, 2001, 1:28am

No luck for me. Looks like I’ll have to wait for a magic bullet from
someone.
Thanks for the info
Robert C.

Chip Nayak wrote:

I have a similar problem with ps-2 mouse on my laptop. However,
disconnecting and re-connecting the mouse brings it back to life.
This happens only after upgrading to 6.1.

Thanks.
Best regards.
– chip

“Robert Craig” <> rcraig@sympatico.ca> > wrote in message
news:> 3B48A490.4A5216D9@sympatico.ca> …
After upgrading to 6.1, I’ve found that my PS-2 Logitech wireless mouse
(which used to work under 6.0) no longer works. I’ve seen the “disable
legascy USB” note in QDN for the BIOS, but my BIOS has no such option
(it’s a Tyan Trinity board). Any other suggestions would be
appreciated!

Thanks
Robert Craig.

shamad · July 15, 2001, 12:00pm

I am having exactly the same problem on a Compaq Prolinea 5133. legacy USB
Disable does not apply either as old Bios. I tried to disconnect the mouse
w/o any success. I’m stuck

Thanks for any info - Serge

Robert Craig <rcraig@sympatico.ca> wrote in message
news:3B4BABC3.B183DDAA@sympatico.ca…

No luck for me. Looks like I’ll have to wait for a magic bullet from
someone.
Thanks for the info
Robert C.

Chip Nayak wrote:

I have a similar problem with ps-2 mouse on my laptop. However,
disconnecting and re-connecting the mouse brings it back to life.
This happens only after upgrading to 6.1.

Thanks.
Best regards.
– chip

“Robert Craig” <> rcraig@sympatico.ca> > wrote in message
news:> 3B48A490.4A5216D9@sympatico.ca> …
After upgrading to 6.1, I’ve found that my PS-2 Logitech wireless
mouse
(which used to work under 6.0) no longer works. I’ve seen the
“disable
legascy USB” note in QDN for the BIOS, but my BIOS has no such option
(it’s a Tyan Trinity board). Any other suggestions would be
appreciated!

Thanks
Robert Craig.

Warren_Peece1 · July 16, 2001, 5:30pm

Save some room for me on this boat. Worked with 6.0, but not with 6.1
regardless of USB legacy setting.

Alex_Chapiro1 · July 16, 2001, 5:55pm

Could you please also answer to the questions from my mail to shamad’s
request (Mouse not recognized since 6.1)?
In addition: couple of words about your computer?

“Warren Peece” <warren@nospam.com> wrote in message
news:9iv847$mrd$1@inn.qnx.com…

Save some room for me on this boat. Worked with 6.0, but not with 6.1
regardless of USB legacy setting.

-Warren “I forgot my lifejacket” Peece

“shamad” <> shamad@multimania.com> > wrote in message
news:9is0da$nr1$> 1@inn.qnx.com> …
| I am having exactly the same problem on a Compaq Prolinea 5133. legacy
USB
| Disable does not apply either as old Bios. I tried to disconnect the
mouse
| w/o any success. I’m stuck
|
| Thanks for any info - Serge
|
| Robert Craig <> rcraig@sympatico.ca> > wrote in message
| news:> 3B4BABC3.B183DDAA@sympatico.ca> …
| > No luck for me. Looks like I’ll have to wait for a magic bullet from
| > someone.
| > Thanks for the info
| > Robert C.
|
| > Chip Nayak wrote:
|
| > > I have a similar problem with ps-2 mouse on my laptop. However,
| > > disconnecting and re-connecting the mouse brings it back to life.
| > > This happens only after upgrading to 6.1.
|
| > > Thanks.
| > > Best regards.
| > > – chip
|
| > > “Robert Craig” <> rcraig@sympatico.ca> > wrote in message
| > > news:> 3B48A490.4A5216D9@sympatico.ca> …
| > > > After upgrading to 6.1, I’ve found that my PS-2 Logitech wireless
| mouse
| > > > (which used to work under 6.0) no longer works. I’ve seen the
| “disable
| > > > legascy USB” note in QDN for the BIOS, but my BIOS has no such
option
| > > > (it’s a Tyan Trinity board). Any other suggestions would be
| > > > appreciated!
|
| > > > Thanks
| > > > Robert Craig.
|
|