I installed RTP 6.1.0 on a Dell Inspiron 3000. When I run pin, it reports
that the 4 PCMCIA slots are empty. As a result neither my network card
(D-Link DE660) nor my modem card (ActionTec FM560LKI) are detected.
Is there any driver I should load?
Thanks - Serge
Try starting the machine without the card in and then after it started up
insert the card. Does that work better?
“shamad” <shamad@multimania.com> wrote in message
news:9jnhao$n5m$1@inn.qnx.com…
I installed RTP 6.1.0 on a Dell Inspiron 3000. When I run pin, it reports
that the 4 PCMCIA slots are empty. As a result neither my network card
(D-Link DE660) nor my modem card (ActionTec FM560LKI) are detected.
Is there any driver I should load?Thanks - Serge
Thanks for the tip. I tried but still… pin does not display the cards
status.
Actually in the meantime I found another trick. During the boot process I
press space bar, then function Key F11(enumertor disable), then F3 (disable
pcmcia/pccard enumerator and ENTER twice. When logged on, I open a terminal
session and type devp-pccard, then pin and … sometimes… it works. Not
always.
When it is in a good mood I am still stuck as I don’t know what driver to
load. As a reminder my network card is a D-Link DE660
Any help would be welcome
thanks - Serge
Mario Charest <mcharest@zinformatic.com> wrote in message
news:9jp5ua$o8n$1@inn.qnx.com…
Try starting the machine without the card in and then after it started up
insert the card. Does that work better?“shamad” <> shamad@multimania.com> > wrote in message
news:9jnhao$n5m$> 1@inn.qnx.com> …
I installed RTP 6.1.0 on a Dell Inspiron 3000. When I run pin, it
reports
that the 4 PCMCIA slots are empty. As a result neither my network card
(D-Link DE660) nor my modem card (ActionTec FM560LKI) are detected.
Is there any driver I should load?Thanks - Serge
\
Hi,
Once devp-pccard is running…do a pin(with card inserted) make reference to the
base Address and the irq. Then start io-net -dne2000 ioport=???,irq=?? -ptcpip &
Regards,
Joe
shamad <shamad@multimania.com> wrote:
Thanks for the tip. I tried but still… pin does not display the cards
status.
Actually in the meantime I found another trick. During the boot process I
press space bar, then function Key F11(enumertor disable), then F3 (disable
pcmcia/pccard enumerator and ENTER twice. When logged on, I open a terminal
session and type devp-pccard, then pin and … sometimes… it works. Not
always.
When it is in a good mood I am still stuck as I don’t know what driver to
load. As a reminder my network card is a D-Link DE660Any help would be welcome
thanks - Serge
Mario Charest <> mcharest@zinformatic.com> > wrote in message
news:9jp5ua$o8n$> 1@inn.qnx.com> …Try starting the machine without the card in and then after it started up
insert the card. Does that work better?“shamad” <> shamad@multimania.com> > wrote in message
news:9jnhao$n5m$> 1@inn.qnx.com> …
I installed RTP 6.1.0 on a Dell Inspiron 3000. When I run pin, it
reports
that the 4 PCMCIA slots are empty. As a result neither my network card
(D-Link DE660) nor my modem card (ActionTec FM560LKI) are detected.
Is there any driver I should load?Thanks - Serge
\
Joe,
As soon as I enter your command line after having been through what I
described earlier, the OS dies, the mouse gets frozen, no possibility to
access anything and I have to hard reset the computer. This is systematic
Is there any relationship with the fact that with the same initialization
process, I sometimes gets the ioport and irq from my network card (pin) and
most of time not?
Any more ideas?
Serge
Hardware Support Account <hw@qnx.com> wrote in message
news:9js2jg$d4j$1@nntp.qnx.com…
Hi,
Once devp-pccard is running…do a pin(with card inserted) make reference
to the
base Address and the irq. Then start io-net -dne2000
ioport=???,irq=?? -ptcpip &Regards,
Joe
shamad <> shamad@multimania.com> > wrote:
Thanks for the tip. I tried but still… pin does not display the cards
status.
Actually in the meantime I found another trick. During the boot process
I
press space bar, then function Key F11(enumertor disable), then F3
(disable
pcmcia/pccard enumerator and ENTER twice. When logged on, I open a
terminal
session and type devp-pccard, then pin and … sometimes… it works. Not
always.
When it is in a good mood I am still stuck as I don’t know what driver
to
load. As a reminder my network card is a D-Link DE660Any help would be welcome
thanks - Serge
Mario Charest <> mcharest@zinformatic.com> > wrote in message
news:9jp5ua$o8n$> 1@inn.qnx.com> …Try starting the machine without the card in and then after it started
up
insert the card. Does that work better?“shamad” <> shamad@multimania.com> > wrote in message
news:9jnhao$n5m$> 1@inn.qnx.com> …
I installed RTP 6.1.0 on a Dell Inspiron 3000. When I run pin, it
reports
that the 4 PCMCIA slots are empty. As a result neither my network
card
(D-Link DE660) nor my modem card (ActionTec FM560LKI) are detected.
Is there any driver I should load?Thanks - Serge
\
I have a similar problem. I installed RTP6 on my notebook and pin
reports that the 2 PCMCIA slots are empty.
Sock Func Type Flags PID Base
Size IRQ
1 Empty ----MF---------- None
1 Empty ----MF---------- None
2 Empty ----MF---------- None
2 Empty ----MF---------- None
I have a D-Link DFE-650 PCMCIA card. What do I do to install this
network card? Somebody can help me?
pci -vvv reports the follow:
PCI version = 2.10
Class = Bridge (Host/PCI)
Vendor ID = 8086h, Intel Corporation
Device ID = 7190h, 82443BX/ZX 440BX/ZX AGPset Host Bridge
PCI index = 0h
Class Codes = 060000h
Revision ID = 3h
Bus number = 0
Device number = 0
Function num = 0
Status Reg = a210h
Command Reg = 106h
I/O space access disabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents enabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Capabilities Pointer = a0h
Capability ID = 2h
Capabilities = 10h - 1f000202h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 0c 80 00 ff 00 00 00 09 03 10 11 01 00 10 00 11
0x60: 08 10 10 10 10 10 10 10 00 0a c0 00 00 80 00 00
0x70: 20 1f 0a 78 05 00 00 01 26 03 d8 00 10 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 04 61 00 00 00 05 00 00 00 00 00 00
0xA0: 02 00 10 00 02 02 00 1f 00 00 00 00 00 00 00 00
0xB0: 80 00 00 00 30 00 00 00 00 00 00 00 20 10 00 00
0xC0: 00 00 00 00 00 00 00 00 18 0c ff ff 61 00 00 00
0xD0: 00 00 00 00 00 00 00 00 0c 00 00 00 00 00 00 00
0xE0: 4c ad ff bb 8a 3e 00 80 2c d3 f7 cf 9d 3e 00 00
0xF0: 3f 01 00 00 20 f8 00 60 20 0f 00 00 00 00 00 00
Class = Bridge (PCI/PCI)
Vendor ID = 8086h, Intel Corporation
Device ID = 7191h, 82443BX/ZX 440BX/ZX AGPset PCI-to-PCI bridge
PCI index = 0h
Class Codes = 060400h
Revision ID = 3h
Bus number = 0
Device number = 1
Function num = 0
Status Reg = 220h
Command Reg = 1fh
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations monitor
Memory Write and Invalidate enabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 1h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 80h
Cache Line Size= 0h
Primary Bus Number = 0h
Secondary Bus Number = 1h
Subordinate Bus Number = 1h
Secondary Latency Timer = 40h
I/O Base = f0h
I/O Limit = 0h
Secondary Status = 22a0h
Memory Base = f000h
Memory Limit = f7f0h
Prefetchable Memory Base = fff0h
Prefetchable Memory Limit= 0h
Prefetchable Base Upper 32 Bits = 0h
Prefetchable Limit Upper 32 Bits = 0h
I/O Base Upper 16 Bits = ffffh
I/O Limit Upper 16 Bits = ffffh
Bridge Control = 140ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 8c 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac51h, PCI1420 PC Card Controller
PCI index = 0h
Class Codes = 060700h
Revision ID = 0h
Bus number = 0
Device number = 4
Function num = 0
Status Reg = 210h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 8h un-cacheable
ExCA Base Address = ffeff000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 2
Subordinate Bus Number = 2
Secondary Latency Timer = 20h
Memory Base 0 = 0h
Memory Limit 0 = 0h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 0h
I/O Limit 0 = 0h
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 11
Bridge Control = 4c0h
Subsystem Vendor ID = 103ch
Subsystem ID = 14h
Legacy Mode Base Address = 3e0h
System Control = 28449020h
Retry Status = c0h
Card Control = 0h
Device Control = 66h
Buffer Control = 60h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 3c 10 14 00 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 20 90 44 28 00 00 00 00 00 00 00 00 22 1b ac 01
0x90: c0 00 66 60 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 01 00 11 fe 00 00 c0 00 15 08 00 00 1f 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac51h, PCI1420 PC Card Controller
PCI index = 1h
Class Codes = 060700h
Revision ID = 0h
Bus number = 0
Device number = 4
Function num = 1
Status Reg = 210h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 8h un-cacheable
ExCA Base Address = ffefe000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 3
Subordinate Bus Number = 3
Secondary Latency Timer = 20h
Memory Base 0 = 0h
Memory Limit 0 = 0h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 0h
I/O Limit 0 = 0h
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 11
Bridge Control = 4c0h
Subsystem Vendor ID = 103ch
Subsystem ID = 14h
Legacy Mode Base Address = 3e0h
System Control = 28449020h
Retry Status = c0h
Card Control = 0h
Device Control = 66h
Buffer Control = 60h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 3c 10 14 00 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 20 90 44 28 00 00 00 00 00 00 00 00 22 1b ac 01
0x90: c0 00 66 60 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 01 00 11 fe 00 00 c0 00 15 08 00 00 1f 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Class = Bridge (PCI/ISA)
Vendor ID = 8086h, Intel Corporation
Device ID = 7110h, 82371AB/EB PIIX4 ISA Bridge
PCI index = 0h
Class Codes = 060100h
Revision ID = 2h
Bus number = 0
Device number = 7
Function num = 0
Status Reg = 280h
Command Reg = fh
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations monitor
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 4d 00 73 04
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 0b 80 05 05 d0 00 00 00 00 f2 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 0c 0c 00 00 00 00 00 00 00 00
0x80: 00 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 04 40 81 71 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
Class = Mass Storage (IDE)
Vendor ID = 8086h, Intel Corporation
Device ID = 7111h, 82371AB/EB PIIX4 IDE Controller
PCI index = 0h
Class Codes = 010180h
Revision ID = 1h
Bus number = 0
Device number = 7
Function num = 1
Status Reg = 280h
Command Reg = 5h
I/O space access enabled
Memory space access disabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
PCI IO Address = 1050h length 16 enabled
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 07 a3 03 a3 00 00 00 00 05 00 02 02 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
Class = Serial Bus (Universal Serial Bus)
Vendor ID = 8086h, Intel Corporation
Device ID = 7112h, 82371AB/EB PIIX4 USB Interface
PCI index = 0h
Class Codes = 0c0300h
Revision ID = 1h
Bus number = 0
Device number = 7
Function num = 2
Status Reg = 280h
Command Reg = 1h
I/O space access enabled
Memory space access disabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
PCI IO Address = 1060h length 32 enabled
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = INT D
Interrupt line = 5
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
Class = Bridge (Unknown)
Vendor ID = 8086h, Intel Corporation
Device ID = 7113h, 82371AB/EB PIIX4 Power Management Controller
PCI index = 0h
Class Codes = 068000h
Revision ID = 3h
Bus number = 0
Device number = 7
Function num = 3
Status Reg = 280h
Command Reg = 3h
I/O space access enabled
Memory space access enabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 01 10 00 00 0f ff bf ff 3f 3a 00 00 00 00 00 00
0x50: 00 50 1c 00 ff 3f 00 00 17 80 00 02 00 00 00 e0
0x60: 80 00 80 62 00 fe 21 08 78 03 17 00 00 00 00 00
0x70: 2e 00 11 00 00 00 00 00 00 00 00 00 70 03 01 00
0x80: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 41 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
Class = Multimedia (Audio)
Vendor ID = 125dh, ESS Technology
Device ID = 1988h, ES1989 Allegro-1 Audiodrive
PCI index = 0h
Class Codes = 040100h
Revision ID = 12h
Bus number = 0
Device number = 8
Function num = 0
Status Reg = 290h
Command Reg = 5h
I/O space access enabled
Memory space access disabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
PCI IO Address = 1400h length 256 enabled
Subsystem Vendor ID = 103ch
Subsystem ID = 12h
Max Lat = 24ns
Min Gnt = 2ns
PCI Int Pin = INT A
Interrupt line = 5
Capabilities Pointer = c0h
Capability ID = 1h
Capabilities = 7622h - 0h
Device Dependent Registers:
0x40: 60 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 40 00 e0 0a 00 00 00 00 00 01 01 00 21 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 12 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 01 00 22 76 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Class = Communication (Unknown)
Vendor ID = 125dh, ESS Technology
Device ID = 1989h, ES56CVM-PI Allegro-1.COMM PCI Voice+Fax Modem
PCI index = 0h
Class Codes = 078000h
Revision ID = 12h
Bus number = 0
Device number = 8
Function num = 1
Status Reg = 290h
Command Reg = 1h
I/O space access enabled
Memory space access disabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
PCI IO Address = 1800h length 256 enabled
Subsystem Vendor ID = 103ch
Subsystem ID = 12h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = INT A
Interrupt line = 5
Capabilities Pointer = c0h
Capability ID = 1h
Capabilities = f6a2h - 0h
Device Dependent Registers:
0x40: 60 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 40 00 e0 0a 00 00 00 00 00 01 01 00 21 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 12 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 01 00 a2 f6 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Class = Display (VGA)
Vendor ID = 5333h, S3 Incorporated
Device ID = 8c12h, 86C270/274/290/294 Savage MX/IX/MX+MV/IX+MV
PCI index = 0h
Class Codes = 030000h
Revision ID = 13h
Bus number = 1
Device number = 1
Function num = 0
Status Reg = 230h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 8h un-cacheable
PCI Mem Address = f0000000h 32bit length 134217728 enabled
Subsystem Vendor ID = 103ch
Subsystem ID = 14h
Max Lat = 255ns
Min Gnt = 4ns
PCI Int Pin = INT A
Interrupt line = 11
Capabilities Pointer = dch
Capability ID = 1h
Capabilities = 621h - 0h
Capability ID = 2h
Capabilities = 10h - 1f000003h
Device Dependent Registers:
0x40: 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 02 00 10 00 03 00 00 1f 02 01 00 1e 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 01 80 21 06
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Help me, please!!! Somebody knows if there is a qnx driver for the
D-Link DFE-650 PCMCIA? Could I use some driver generic? Which?
“Gustavo” <gandre@usp.br> wrote in message news:aamfqu$91g$1@inn.qnx.com…
I have a similar problem. I installed RTP6 on my notebook and pin
reports that the 2 PCMCIA slots are empty.Sock Func Type Flags PID Base
Size IRQ
1 Empty ----MF---------- None
1 Empty ----MF---------- None
2 Empty ----MF---------- None
2 Empty ----MF---------- NoneI have a D-Link DFE-650 PCMCIA card. What do I do to install this
network card? Somebody can help me?
pci -vvv reports the follow:PCI version = 2.10
Class = Bridge (Host/PCI)
Vendor ID = 8086h, Intel Corporation
Device ID = 7190h, 82443BX/ZX 440BX/ZX AGPset Host Bridge
PCI index = 0h
Class Codes = 060000h
Revision ID = 3h
Bus number = 0
Device number = 0
Function num = 0
Status Reg = a210h
Command Reg = 106h
I/O space access disabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents enabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Capabilities Pointer = a0h
Capability ID = 2h
Capabilities = 10h - 1f000202h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 0c 80 00 ff 00 00 00 09 03 10 11 01 00 10 00 11
0x60: 08 10 10 10 10 10 10 10 00 0a c0 00 00 80 00 00
0x70: 20 1f 0a 78 05 00 00 01 26 03 d8 00 10 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 04 61 00 00 00 05 00 00 00 00 00 00
0xA0: 02 00 10 00 02 02 00 1f 00 00 00 00 00 00 00 00
0xB0: 80 00 00 00 30 00 00 00 00 00 00 00 20 10 00 00
0xC0: 00 00 00 00 00 00 00 00 18 0c ff ff 61 00 00 00
0xD0: 00 00 00 00 00 00 00 00 0c 00 00 00 00 00 00 00
0xE0: 4c ad ff bb 8a 3e 00 80 2c d3 f7 cf 9d 3e 00 00
0xF0: 3f 01 00 00 20 f8 00 60 20 0f 00 00 00 00 00 00
Class = Bridge (PCI/PCI)
Vendor ID = 8086h, Intel Corporation
Device ID = 7191h, 82443BX/ZX 440BX/ZX AGPset PCI-to-PCI bridge
PCI index = 0h
Class Codes = 060400h
Revision ID = 3h
Bus number = 0
Device number = 1
Function num = 0
Status Reg = 220h
Command Reg = 1fh
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations monitor
Memory Write and Invalidate enabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 1h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 80h
Cache Line Size= 0h
Primary Bus Number = 0h
Secondary Bus Number = 1h
Subordinate Bus Number = 1h
Secondary Latency Timer = 40h
I/O Base = f0h
I/O Limit = 0h
Secondary Status = 22a0h
Memory Base = f000h
Memory Limit = f7f0h
Prefetchable Memory Base = fff0h
Prefetchable Memory Limit= 0h
Prefetchable Base Upper 32 Bits = 0h
Prefetchable Limit Upper 32 Bits = 0h
I/O Base Upper 16 Bits = ffffh
I/O Limit Upper 16 Bits = ffffh
Bridge Control = 140ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 8c 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac51h, PCI1420 PC Card Controller
PCI index = 0h
Class Codes = 060700h
Revision ID = 0h
Bus number = 0
Device number = 4
Function num = 0
Status Reg = 210h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 8h un-cacheable
ExCA Base Address = ffeff000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 2
Subordinate Bus Number = 2
Secondary Latency Timer = 20h
Memory Base 0 = 0h
Memory Limit 0 = 0h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 0h
I/O Limit 0 = 0h
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 11
Bridge Control = 4c0h
Subsystem Vendor ID = 103ch
Subsystem ID = 14h
Legacy Mode Base Address = 3e0h
System Control = 28449020h
Retry Status = c0h
Card Control = 0h
Device Control = 66h
Buffer Control = 60h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 3c 10 14 00 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 20 90 44 28 00 00 00 00 00 00 00 00 22 1b ac 01
0x90: c0 00 66 60 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 01 00 11 fe 00 00 c0 00 15 08 00 00 1f 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Class = Bridge (CardBus)
Vendor ID = 104ch, Texas Instruments
Device ID = ac51h, PCI1420 PC Card Controller
PCI index = 1h
Class Codes = 060700h
Revision ID = 0h
Bus number = 0
Device number = 4
Function num = 1
Status Reg = 210h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 8h un-cacheable
ExCA Base Address = ffefe000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 3
Subordinate Bus Number = 3
Secondary Latency Timer = 20h
Memory Base 0 = 0h
Memory Limit 0 = 0h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 0h
I/O Limit 0 = 0h
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 11
Bridge Control = 4c0h
Subsystem Vendor ID = 103ch
Subsystem ID = 14h
Legacy Mode Base Address = 3e0h
System Control = 28449020h
Retry Status = c0h
Card Control = 0h
Device Control = 66h
Buffer Control = 60h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 3c 10 14 00 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 20 90 44 28 00 00 00 00 00 00 00 00 22 1b ac 01
0x90: c0 00 66 60 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 01 00 11 fe 00 00 c0 00 15 08 00 00 1f 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Class = Bridge (PCI/ISA)
Vendor ID = 8086h, Intel Corporation
Device ID = 7110h, 82371AB/EB PIIX4 ISA Bridge
PCI index = 0h
Class Codes = 060100h
Revision ID = 2h
Bus number = 0
Device number = 7
Function num = 0
Status Reg = 280h
Command Reg = fh
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations monitor
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 4d 00 73 04
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 0b 80 05 05 d0 00 00 00 00 f2 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 0c 0c 00 00 00 00 00 00 00 00
0x80: 00 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 04 40 81 71 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
Class = Mass Storage (IDE)
Vendor ID = 8086h, Intel Corporation
Device ID = 7111h, 82371AB/EB PIIX4 IDE Controller
PCI index = 0h
Class Codes = 010180h
Revision ID = 1h
Bus number = 0
Device number = 7
Function num = 1
Status Reg = 280h
Command Reg = 5h
I/O space access enabled
Memory space access disabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
PCI IO Address = 1050h length 16 enabled
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 07 a3 03 a3 00 00 00 00 05 00 02 02 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
Class = Serial Bus (Universal Serial Bus)
Vendor ID = 8086h, Intel Corporation
Device ID = 7112h, 82371AB/EB PIIX4 USB Interface
PCI index = 0h
Class Codes = 0c0300h
Revision ID = 1h
Bus number = 0
Device number = 7
Function num = 2
Status Reg = 280h
Command Reg = 1h
I/O space access enabled
Memory space access disabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
PCI IO Address = 1060h length 32 enabled
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = INT D
Interrupt line = 5
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
Class = Bridge (Unknown)
Vendor ID = 8086h, Intel Corporation
Device ID = 7113h, 82371AB/EB PIIX4 Power Management Controller
PCI index = 0h
Class Codes = 068000h
Revision ID = 3h
Bus number = 0
Device number = 7
Function num = 3
Status Reg = 280h
Command Reg = 3h
I/O space access enabled
Memory space access enabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 01 10 00 00 0f ff bf ff 3f 3a 00 00 00 00 00 00
0x50: 00 50 1c 00 ff 3f 00 00 17 80 00 02 00 00 00 e0
0x60: 80 00 80 62 00 fe 21 08 78 03 17 00 00 00 00 00
0x70: 2e 00 11 00 00 00 00 00 00 00 00 00 70 03 01 00
0x80: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 41 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00
Class = Multimedia (Audio)
Vendor ID = 125dh, ESS Technology
Device ID = 1988h, ES1989 Allegro-1 Audiodrive
PCI index = 0h
Class Codes = 040100h
Revision ID = 12h
Bus number = 0
Device number = 8
Function num = 0
Status Reg = 290h
Command Reg = 5h
I/O space access enabled
Memory space access disabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
PCI IO Address = 1400h length 256 enabled
Subsystem Vendor ID = 103ch
Subsystem ID = 12h
Max Lat = 24ns
Min Gnt = 2ns
PCI Int Pin = INT A
Interrupt line = 5
Capabilities Pointer = c0h
Capability ID = 1h
Capabilities = 7622h - 0h
Device Dependent Registers:
0x40: 60 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 40 00 e0 0a 00 00 00 00 00 01 01 00 21 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 12 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 01 00 22 76 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Class = Communication (Unknown)
Vendor ID = 125dh, ESS Technology
Device ID = 1989h, ES56CVM-PI Allegro-1.COMM PCI Voice+Fax Modem
PCI index = 0h
Class Codes = 078000h
Revision ID = 12h
Bus number = 0
Device number = 8
Function num = 1
Status Reg = 290h
Command Reg = 1h
I/O space access enabled
Memory space access disabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
PCI IO Address = 1800h length 256 enabled
Subsystem Vendor ID = 103ch
Subsystem ID = 12h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = INT A
Interrupt line = 5
Capabilities Pointer = c0h
Capability ID = 1h
Capabilities = f6a2h - 0h
Device Dependent Registers:
0x40: 60 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 40 00 e0 0a 00 00 00 00 00 01 01 00 21 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 12 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 01 00 a2 f6 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Class = Display (VGA)
Vendor ID = 5333h, S3 Incorporated
Device ID = 8c12h, 86C270/274/290/294 Savage MX/IX/MX+MV/IX+MV
PCI index = 0h
Class Codes = 030000h
Revision ID = 13h
Bus number = 1
Device number = 1
Function num = 0
Status Reg = 230h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 8h un-cacheable
PCI Mem Address = f0000000h 32bit length 134217728 enabled
Subsystem Vendor ID = 103ch
Subsystem ID = 14h
Max Lat = 255ns
Min Gnt = 4ns
PCI Int Pin = INT A
Interrupt line = 11
Capabilities Pointer = dch
Capability ID = 1h
Capabilities = 621h - 0h
Capability ID = 2h
Capabilities = 10h - 1f000003h
Device Dependent Registers:
0x40: 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 02 00 10 00 03 00 00 1f 02 01 00 1e 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 01 80 21 06
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
\
There is no driver for the DFE-650 as this is a 10/100 PCMCIA card. We only
support 10/100 CardBus cards.
Previously, Gustavo wrote in qdn.public.qnxrtp.installation:
Help me, please!!! Somebody knows if there is a qnx driver for the
D-Link DFE-650 PCMCIA? Could I use some driver generic? Which?
“Gustavo” <> gandre@usp.br> > wrote in message news:aamfqu$91g$> 1@inn.qnx.com> …
I have a similar problem. I installed RTP6 on my notebook and pin
reports that the 2 PCMCIA slots are empty.Sock Func Type Flags PID Base
Size IRQ
1 Empty ----MF---------- None
1 Empty ----MF---------- None
2 Empty ----MF---------- None
2 Empty ----MF---------- NoneI have a D-Link DFE-650 PCMCIA card. What do I do to install this
network card? Somebody can help me?
pci -vvv reports the follow:
[snip]
I will buy a PCMCIA card since I could not configure the card that I
have currently (D-Link DFE-650 PCMCIA). Somebody could indicate me the best
PCMCIA card to be used under the QNX?
“Hugh Brown” <hsbrown@qnx.com> wrote in message
news:Voyager.020503084409.12895L@node90.ott.qnx.com…
There is no driver for the DFE-650 as this is a 10/100 PCMCIA card. We
only
support 10/100 CardBus cards.Previously, Gustavo wrote in qdn.public.qnxrtp.installation:
Help me, please!!! Somebody knows if there is a qnx driver for the
D-Link DFE-650 PCMCIA? Could I use some driver generic? Which?
“Gustavo” <> gandre@usp.br> > wrote in message
news:aamfqu$91g$> 1@inn.qnx.com> …
I have a similar problem. I installed RTP6 on my notebook and pin
reports that the 2 PCMCIA slots are empty.Sock Func Type Flags PID
Base
Size IRQ
1 Empty ----MF---------- None
1 Empty ----MF---------- None
2 Empty ----MF---------- None
2 Empty ----MF---------- NoneI have a D-Link DFE-650 PCMCIA card. What do I do to install this
network card? Somebody can help me?
pci -vvv reports the follow:[snip]