I’ve just tried the 6.2 NC and at least contribute a note.
My network card (a 3Com 3C905C-TX pci card) no longer works (it worked
perfecly under 6.1a). QNX seems to recognize it (as I see eh0 on the
network configuration utility) but no actual packets are sent through
this card. Only the local loopback interface and localhost are pingable
(127.0.0.1 and 192.168.0.1).
I’ve just tried the 6.2 NC and at least contribute a note.
My network card (a 3Com 3C905C-TX pci card) no longer works (it worked
perfecly under 6.1a). QNX seems to recognize it (as I see eh0 on the
network configuration utility) but no actual packets are sent through
this card. Only the local loopback interface and localhost are pingable
(127.0.0.1 and 192.168.0.1).
It might not be the 3COM driver:
I also have this problem with an ACCTON PCMCIA Ethernet card. It used to
work in 6.1 using the ne2000 driver.
In 6.2 it is installed by the PNP, but doesn’t send or receive anything
except to itself.
I tried to restart devp-pccard (with the -w8 option) and io-net manually as
I used to in 6.1, but it remains the same.
I have the same Problem. Anyone else out there find out what’s the matter
with the 3COM driver??
Jeff Holtz
Electro Scientific Industries, Inc. holtzj@esi.com
“Yuri D’Elia” <> wavexx@hydra.ubiest.com> > wrote in message
news:> slrnagi32r.vio.wavexx@hydra.hydra.ubi.intra> …
I’ve just tried the 6.2 NC and at least contribute a note.
My network card (a 3Com 3C905C-TX pci card) no longer works (it worked
perfecly under 6.1a). QNX seems to recognize it (as I see eh0 on the
network configuration utility) but no actual packets are sent through
this card. Only the local loopback interface and localhost are pingable
(127.0.0.1 and 192.168.0.1).
I have the same Problem. Anyone else out there find out what’s the matter
with the 3COM driver??
Jeff Holtz
Electro Scientific Industries, Inc. holtzj@esi.com
“Yuri D’Elia” <> wavexx@hydra.ubiest.com> > wrote in message
news:> slrnagi32r.vio.wavexx@hydra.hydra.ubi.intra> …
I’ve just tried the 6.2 NC and at least contribute a note.
My network card (a 3Com 3C905C-TX pci card) no longer works (it worked
perfecly under 6.1a). QNX seems to recognize it (as I see eh0 on the
network configuration utility) but no actual packets are sent through
this card. Only the local loopback interface and localhost are pingable
(127.0.0.1 and 192.168.0.1).
We have moved back to 6.1A for other reasons but what I eventaully found out
was that if I started 6.2, Physically unpluged the card, replugged in the
card, then reran dhcp. It would work. Go figure. Thought I’d pass along
the info though
–
Jeffrey B. Holtz
Software Engineering
Electro Scientific Industries, Inc.
Ph: 734-332-7054
Fax: 734-332-7077
email: holtzj@esi.com
“kirk” <kirussel@NOSPAMrogers.com> wrote in message
news:al6305$n4b$1@inn.qnx.com…
What is the output of nicinfo?
Jeff Holtz <> holtzj@mediaone.net> > wrote:
I have the same Problem. Anyone else out there find out what’s the
matter
with the 3COM driver??
Jeff Holtz
Electro Scientific Industries, Inc. holtzj@esi.com
“Yuri D’Elia” <> wavexx@hydra.ubiest.com> > wrote in message
news:> slrnagi32r.vio.wavexx@hydra.hydra.ubi.intra> …
I’ve just tried the 6.2 NC and at least contribute a note.
My network card (a 3Com 3C905C-TX pci card) no longer works (it worked
perfecly under 6.1a). QNX seems to recognize it (as I see eh0 on the
network configuration utility) but no actual packets are sent through
this card. Only the local loopback interface and localhost are pingable
(127.0.0.1 and 192.168.0.1).