Installing Momentics PE

QNX Newsgroups (Archives) qdn.public.qnxrtp.installation
1

After a installing Momentics on a Win 2000 system and running the command:
qcc -V and the result is the correct but when i try to start a C++ project
in the IDE but it doesn’t work. A get a message box saying

Installation Error
QNX SDK has not been installed or there is a licensing problem

What i understand is my license installed correctly and i have installed the
target-specific packages for x86.
What is wrong?

2

On Mon, 15 Jul 2002 12:39:46 +0200, “Bengt” <bengt.hurtig@cellavision.com> wrote:

After a installing Momentics on a Win 2000 system and running the command:
qcc -V and the result is the correct but when i try to start a C++ project
in the IDE but it doesn’t work. A get a message box saying

Installation Error
QNX SDK has not been installed or there is a licensing problem

What i understand is my license installed correctly and i have installed the
target-specific packages for x86.
What is wrong?

The FlexLM server/service may not be running.

3

“Alex Cellarius” <acellarius@yahoo.com> wrote in message
news:1103_1026729808@pentium4…

On Mon, 15 Jul 2002 12:39:46 +0200, “Bengt” <> bengt.hurtig@cellavision.com
wrote:
After a installing Momentics on a Win 2000 system and running the
command:
qcc -V and the result is the correct but when i try to start a C++
project
in the IDE but it doesn’t work. A get a message box saying

Installation Error
QNX SDK has not been installed or there is a licensing problem

What i understand is my license installed correctly and i have installed
the
target-specific packages for x86.
What is wrong?



The FlexLM server/service may not be running.

The FlexLM server is running else the qcc -V command fails. I have stopped
the QNXlm License Proxy service on my computer and then the command: qcc -V
fails.
/Bengt

4

If you open the FlexLM control panel and ask for server status do you have
both a QNX_SE and QNX_PE license being served? The IDE will ask for both
while qcc only asks for SE.

chris

Bengt <bengt.hurtig@cellavision.com> wrote:

After a installing Momentics on a Win 2000 system and running the command:
qcc -V and the result is the correct but when i try to start a C++ project
in the IDE but it doesn’t work. A get a message box saying

Installation Error
QNX SDK has not been installed or there is a licensing problem

What i understand is my license installed correctly and i have installed the
target-specific packages for x86.
What is wrong?

–
Chris McKillop <cdm@qnx.com> “The faster I go, the behinder I get.”
Software Engineer, QSSL – Lewis Carroll –
http://qnx.wox.org/

5

Both QNX_SE and QNX_PE license is being served . When I start the IDE the
FexLM debuglog on the server, I am using a remote server, states that the
QNX_PE is checked out and then checked in again. I can compile at the
command prompt.
/Bengt

“Chris McKillop” <cdm@qnx.com> wrote in message
news:agv45j$lpu$1@nntp.qnx.com…

If you open the FlexLM control panel and ask for server status do you have
both a QNX_SE and QNX_PE license being served? The IDE will ask for both
while qcc only asks for SE.

chris

Bengt <> bengt.hurtig@cellavision.com> > wrote:
After a installing Momentics on a Win 2000 system and running the
command:
qcc -V and the result is the correct but when i try to start a C++
project
in the IDE but it doesn’t work. A get a message box saying

Installation Error
QNX SDK has not been installed or there is a licensing problem

What i understand is my license installed correctly and i have installed
the
target-specific packages for x86.
What is wrong?


\

Chris McKillop <> cdm@qnx.com> > “The faster I go, the behinder I get.”
Software Engineer, QSSL – Lewis Carroll –
http://qnx.wox.org/

6

I have found the problem I rewrote the QNX_HOST and QNX_TARGET environmental
variables, there must have been a scrap char same where.

/Bengt

“Bengt” <bengt.hurtig@cellavision.com> wrote in message
news:ah0vk6$4mr$1@nntp.qnx.com…

Both QNX_SE and QNX_PE license is being served . When I start the IDE the
FexLM debuglog on the server, I am using a remote server, states that the
QNX_PE is checked out and then checked in again. I can compile at the
command prompt.
/Bengt

“Chris McKillop” <> cdm@qnx.com> > wrote in message
news:agv45j$lpu$> 1@nntp.qnx.com> …

If you open the FlexLM control panel and ask for server status do you
have
both a QNX_SE and QNX_PE license being served? The IDE will ask for
both
while qcc only asks for SE.

chris

Bengt <> bengt.hurtig@cellavision.com> > wrote:
After a installing Momentics on a Win 2000 system and running the
command:
qcc -V and the result is the correct but when i try to start a C++
project
in the IDE but it doesn’t work. A get a message box saying

Installation Error
QNX SDK has not been installed or there is a licensing problem

What i understand is my license installed correctly and i have
installed
the
target-specific packages for x86.
What is wrong?


\

Chris McKillop <> cdm@qnx.com> > “The faster I go, the behinder I
get.”
Software Engineer, QSSL – Lewis Carroll –
http://qnx.wox.org/
\