Yes I was stuffing about inside the Shelf Cfg applit trying to plend the 2
bars together (the launch bar/task bar on oneside & the shelf bar on the
otherside), By putting a launch bar & task bar on the same side as the
shelf bar with all the shortcuts, then deleting the original launch & task
bar. But I got a big GUI crash. Now I just get a blank Desktop & if I right
click the mouse & click ‘shelf Cfg’ in the contextual menu nothing happens.
How do I get everything back? Thanks.
If worse come to worse I’ll spose I’ll have to re-install.
BTW, I’m new to Unix, so I’m just wondering how I set up my printer (Epson
600, its s’pose to be supported), so I can click the printer button on say
the voyager button bar & the page prints away.
I managed to install the wheelmouse driver from QNXstart by walking into a
bookstore & copying the ‘gunzip filename.tar.gz’ & the ‘tar xvf
filename.tar’ terminal commands out of a Unix book & using them, then
searching arround for a file with the same name to replace. & it all worked
out ok.
Do I need to know some esoteric terminal commands to re-install my GUI &
setup my printer? (the terminal still comes up when I click it in the
‘rightclick’ contextual menu)
BTW, There’s a ESS Maestro2 driver avaliable at BeBits, would it be possible
to reverse engineer that for QNX?
Also can someone recommend a good Unix book that pertinent to QNX, that also
explains all the BASH commands?
Yes I was stuffing about inside the Shelf Cfg applit trying to plend the 2
bars together (the launch bar/task bar on oneside & the shelf bar on the
otherside), By putting a launch bar & task bar on the same side as the
shelf bar with all the shortcuts, then deleting the original launch & task
bar. But I got a big GUI crash. Now I just get a blank Desktop & if I right
click the mouse & click ‘shelf Cfg’ in the contextual menu nothing happens.
How do I get everything back? Thanks.
If worse come to worse I’ll spose I’ll have to re-install.
BTW, I’m new to Unix, so I’m just wondering how I set up my printer (Epson
600, its s’pose to be supported), so I can click the printer button on say
the voyager button bar & the page prints away.
I managed to install the wheelmouse driver from QNXstart by walking into a
bookstore & copying the ‘gunzip filename.tar.gz’ & the ‘tar xvf
filename.tar’ terminal commands out of a Unix book & using them, then
searching arround for a file with the same name to replace. & it all worked
out ok.
Do I need to know some esoteric terminal commands to re-install my GUI &
setup my printer? (the terminal still comes up when I click it in the
‘rightclick’ contextual menu)
BTW, There’s a ESS Maestro2 driver avaliable at BeBits, would it be possible
to reverse engineer that for QNX?
Also can someone recommend a good Unix book that pertinent to QNX, that also
explains all the BASH commands?
I also recommend to save the ~/.ph/shelf/shelf.cfg file before making any
drastic changes to it. If the new one doesn’t work, you can
then revert to the old one.
Sylvain
David LeBlanc <dleblanc@qnx.com> wrote in message
news:973d3p$fbb$1@nntp.qnx.com…
Bring up a pterm and type
rm -r ~/.ph/shelf
Next time you restart shelf you should be reverted to a safe, default
configuration.
Mick <> mickvb@optushome.com.au> > wrote:
Yes I was stuffing about inside the Shelf Cfg applit trying to plend the
2
bars together (the launch bar/task bar on oneside & the shelf bar on the
otherside), By putting a launch bar & task bar on the same side as the
shelf bar with all the shortcuts, then deleting the original launch &
task
bar. But I got a big GUI crash. Now I just get a blank Desktop & if I
right
click the mouse & click ‘shelf Cfg’ in the contextual menu nothing
happens.
How do I get everything back? Thanks.
If worse come to worse I’ll spose I’ll have to re-install.
BTW, I’m new to Unix, so I’m just wondering how I set up my printer
(Epson
600, its s’pose to be supported), so I can click the printer button on
say
the voyager button bar & the page prints away.
I managed to install the wheelmouse driver from QNXstart by walking into
a
bookstore & copying the ‘gunzip filename.tar.gz’ & the ‘tar xvf
filename.tar’ terminal commands out of a Unix book & using them, then
searching arround for a file with the same name to replace. & it all
worked
out ok.
Do I need to know some esoteric terminal commands to re-install my GUI &
setup my printer? (the terminal still comes up when I click it in the
‘rightclick’ contextual menu)
BTW, There’s a ESS Maestro2 driver avaliable at BeBits, would it be
possible
to reverse engineer that for QNX?
Also can someone recommend a good Unix book that pertinent to QNX, that
also
explains all the BASH commands?
Next time you restart shelf you should be reverted to a safe, default
configuration.
Mick <> mickvb@optushome.com.au> > wrote:
Yes I was stuffing about inside the Shelf Cfg applit trying to plend the
2
bars together (the launch bar/task bar on oneside & the shelf bar on the
otherside), By putting a launch bar & task bar on the same side as the
shelf bar with all the shortcuts, then deleting the original launch &
task
bar. But I got a big GUI crash. Now I just get a blank Desktop & if I
right
click the mouse & click ‘shelf Cfg’ in the contextual menu nothing
happens.
How do I get everything back? Thanks.
If worse come to worse I’ll spose I’ll have to re-install.
BTW, I’m new to Unix, so I’m just wondering how I set up my printer
(Epson
600, its s’pose to be supported), so I can click the printer button on
say
the voyager button bar & the page prints away.
I managed to install the wheelmouse driver from QNXstart by walking into
a
bookstore & copying the ‘gunzip filename.tar.gz’ & the ‘tar xvf
filename.tar’ terminal commands out of a Unix book & using them, then
searching arround for a file with the same name to replace. & it all
worked
out ok.
Do I need to know some esoteric terminal commands to re-install my GUI &
setup my printer? (the terminal still comes up when I click it in the
‘rightclick’ contextual menu)
BTW, There’s a ESS Maestro2 driver avaliable at BeBits, would it be
possible
to reverse engineer that for QNX?
Also can someone recommend a good Unix book that pertinent to QNX, that
also
explains all the BASH commands?