I’m trying to configure a Elo Smartset touch screen. It kind of works
almost.
But the X & Y coordinates are mixed up. As I move my finger laft to right
the cursor moves up and down. As I move my finger up and down the cursor
moves left to right.
What gives? How do I fix it?
–
Bill Caroselli – 1(626) 824-7983
Q-TPS Consulting
QTPS@EarthLink.net
ping
“Bill Caroselli” <qtps@earthlink.net> wrote in message
news:a76gkf$t7q$1@inn.qnx.com…
I’m trying to configure a Elo Smartset touch screen. It kind of works
almost.
But the X & Y coordinates are mixed up. As I move my finger laft to right
the cursor moves up and down. As I move my finger up and down the cursor
moves left to right.
What gives? How do I fix it?
–
Bill Caroselli – 1(626) 824-7983
Q-TPS Consulting
QTPS@EarthLink.net
Try this solution:
http://qdn.qnx.com/support/bok/solution.qnx?10190
-Brian
“Bill Caroselli” <qtps@earthlink.net> wrote in message
news:a76gkf$t7q$1@inn.qnx.com…
I’m trying to configure a Elo Smartset touch screen. It kind of works
almost.
But the X & Y coordinates are mixed up. As I move my finger laft to right
the cursor moves up and down. As I move my finger up and down the cursor
moves left to right.
What gives? How do I fix it?
–
Bill Caroselli – 1(626) 824-7983
Q-TPS Consulting
QTPS@EarthLink.net
Cool. That worked. Two comments.
-
the article says to “flip the last bit”. Bit makes me think binary but
this is an ascii file. What it should say is to toggle the ascii value
to/from 0 <==> 1.
-
I know that QSSL has given up on QNX4 but can this fix make into a bug
dix release?
–
Bill Caroselli – 1(626) 824-7983
Q-TPS Consulting
QTPS@EarthLink.net
“Brian Repman” <b-repman@att.net> wrote in message
news:a7aano$pi0$1@inn.qnx.com…
Try this solution:
http://qdn.qnx.com/support/bok/solution.qnx?10190
-Brian
“Bill Caroselli” <> qtps@earthlink.net> > wrote in message
news:a76gkf$t7q$> 1@inn.qnx.com> …
I’m trying to configure a Elo Smartset touch screen. It kind of works
almost.
But the X & Y coordinates are mixed up. As I move my finger laft to
right
the cursor moves up and down. As I move my finger up and down the cursor
moves left to right.
What gives? How do I fix it?
–
Bill Caroselli – 1(626) 824-7983
Q-TPS Consulting
QTPS@EarthLink.net
\
Were you trying to use the “calib” program, or the older “acalib” program?
“Bill Caroselli” <qtps@earthlink.net> wrote in message
news:a7amsp$58o$1@inn.qnx.com…
Cool. That worked. Two comments.
-
the article says to “flip the last bit”. Bit makes me think binary but
this is an ascii file. What it should say is to toggle the ascii value
to/from 0 <==> 1.
-
I know that QSSL has given up on QNX4 but can this fix make into a bug
dix release?
–
Bill Caroselli – 1(626) 824-7983
Q-TPS Consulting
QTPS@EarthLink.net
“Brian Repman” <> b-repman@att.net> > wrote in message
news:a7aano$pi0$> 1@inn.qnx.com> …
Try this solution:
http://qdn.qnx.com/support/bok/solution.qnx?10190
-Brian
“Bill Caroselli” <> qtps@earthlink.net> > wrote in message
news:a76gkf$t7q$> 1@inn.qnx.com> …
I’m trying to configure a Elo Smartset touch screen. It kind of works
almost.
But the X & Y coordinates are mixed up. As I move my finger laft to
right
the cursor moves up and down. As I move my finger up and down the
cursor
moves left to right.
What gives? How do I fix it?
–
Bill Caroselli – 1(626) 824-7983
Q-TPS Consulting
QTPS@EarthLink.net
\
Good point. I don’t know but I’ll check it out.
Thank you.
–
Bill Caroselli – 1(626) 824-7983
Q-TPS Consulting
QTPS@EarthLink.net
“Ivan Bannon” <ivan.bannon@rjginc.com> wrote in message
news:a7npi1$j56$1@inn.qnx.com…
Were you trying to use the “calib” program, or the older “acalib” program?
“Bill Caroselli” <> qtps@earthlink.net> > wrote in message
news:a7amsp$58o$> 1@inn.qnx.com> …
Cool. That worked. Two comments.
-
the article says to “flip the last bit”. Bit makes me think binary
but
this is an ascii file. What it should say is to toggle the ascii value
to/from 0 <==> 1.
-
I know that QSSL has given up on QNX4 but can this fix make into a
bug
dix release?
–
Bill Caroselli – 1(626) 824-7983
Q-TPS Consulting
QTPS@EarthLink.net
“Brian Repman” <> b-repman@att.net> > wrote in message
news:a7aano$pi0$> 1@inn.qnx.com> …
Try this solution:
http://qdn.qnx.com/support/bok/solution.qnx?10190
-Brian
“Bill Caroselli” <> qtps@earthlink.net> > wrote in message
news:a76gkf$t7q$> 1@inn.qnx.com> …
I’m trying to configure a Elo Smartset touch screen. It kind of
works
almost.
But the X & Y coordinates are mixed up. As I move my finger laft to
right
the cursor moves up and down. As I move my finger up and down the
cursor
moves left to right.
What gives? How do I fix it?
–
Bill Caroselli – 1(626) 824-7983
Q-TPS Consulting
QTPS@EarthLink.net
\