XFree86 4.1.0 setup question

Hello,

I installed the xfree86-4.1.0-1-bin-qnx6.tar.gz archive to my rtp box.
I ran xf86config and then “X -probeonly”, which told X couldn’t find
my VGA card:
(II) VGA: Generic VGA driver (version 4.0) for chipsets: generic
(–) Assigning device section with no busID to primary device
(–) Chipset generic found
(EE) VGA(0): No Display subsection in Screen section “Screen 1” for
depth/fbbpp 4/4
(EE) Screen(s) found, but none have a usable configuration.

Any hints on configuration? TIA.

hey Kirk!

Try doing “XFree86 -configure” and then add in the following
stuff for mouse support…

Section “InputDevice”
Identifier “Mouse0”
Driver “mouse”
Option “Device” “/dev/devi/mouse0”
Option “Protocol” “OsMouse”
Option “Emulate3Buttons” “off”
Option “ZAxisMapping” “4 5”
EndSection

Also - be sure to devi-hirun in no-Photon-resmgr mode to
get the /dev/devi interface setup.

chris


On Sun, Oct 21, 2001 at 06:55:18PM -0700, kirk russell wrote:

Hello,

I installed the xfree86-4.1.0-1-bin-qnx6.tar.gz archive to my rtp box.
I ran xf86config and then “X -probeonly”, which told X couldn’t find
my VGA card:
(II) VGA: Generic VGA driver (version 4.0) for chipsets: generic
(–) Assigning device section with no busID to primary device
(–) Chipset generic found
(EE) VGA(0): No Display subsection in Screen section “Screen 1” for
depth/fbbpp 4/4
(EE) Screen(s) found, but none have a usable configuration.

Any hints on configuration? TIA.


\


openqnx-developer mailing list
openqnx-developer=> 5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org
https://lists.sourceforge.net/lists/listinfo/openqnx-developer

cdm=> mMf908IxFcw@public.gmane.org > “The faster I go, the behinder I get.”

Chris McKillop – Lewis Carroll –
Software Engineer, QSSL
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

Goto the mailing list page
http://lists.sourceforge.net/lists/listinfo/openqnx-developer
check the archive and see if my installation instruction helps.
While you are on there, you might want to join the list so that
you can read replies to your post if any.

Frank

On Sun, 21 Oct 2001, kirk russell wrote:

Hello,

I installed the xfree86-4.1.0-1-bin-qnx6.tar.gz archive to my rtp box.
I ran xf86config and then “X -probeonly”, which told X couldn’t find
my VGA card:
(II) VGA: Generic VGA driver (version 4.0) for chipsets: generic
(–) Assigning device section with no busID to primary device
(–) Chipset generic found
(EE) VGA(0): No Display subsection in Screen section “Screen 1” for
depth/fbbpp 4/4
(EE) Screen(s) found, but none have a usable configuration.

Any hints on configuration? TIA.


\


openqnx-developer mailing list
openqnx-developer=> 5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org
https://lists.sourceforge.net/lists/listinfo/openqnx-developer