I installed 6.2.1NC, but I cannot have the ethernet card running: when I
configure the en0 to use DHCP, I got an pop-up message “netmanager
error:could not configure DHCP on interface en0. netmanager error: couldnot
reach DHCP server on interface en0.”
I have a Macronix PCI ethernet adatper, and I am using driver “io-net -d
tulip -p tcpip”.
Can anyone help me please?
I have the same problem with a ne2000 compatible board. It is a CM202 from
Real Time Devices.
I am suspecting a defective board. Maybe it is the same for you.
If someone has a better idea…
“xinni” <xiahnisong2001@rogers.com> wrote in message
news:bg4s84$47j$1@inn.qnx.com…
I installed 6.2.1NC, but I cannot have the ethernet card running: when I
configure the en0 to use DHCP, I got an pop-up message “netmanager
error:could not configure DHCP on interface en0. netmanager error:
couldnot
reach DHCP server on interface en0.”I have a Macronix PCI ethernet adatper, and I am using driver “io-net -d
tulip -p tcpip”.Can anyone help me please?
My network card works fine with windows XP and Linux 8.0. so I don’t think
it’s an issue.
Is this a known bug with 6.2.1?
“Frédéric Paquet-Roy” <frederic.paquet-roy.1@ens.etsmtl.ca> wrote in message
news:bgbkcc$94h$1@inn.qnx.com…
I have the same problem with a ne2000 compatible board. It is a CM202
from
Real Time Devices.
I am suspecting a defective board. Maybe it is the same for you.If someone has a better idea…
“xinni” <> xiahnisong2001@rogers.com> > wrote in message
news:bg4s84$47j$> 1@inn.qnx.com> …
I installed 6.2.1NC, but I cannot have the ethernet card running: when I
configure the en0 to use DHCP, I got an pop-up message “netmanager
error:could not configure DHCP on interface en0. netmanager error:
couldnot
reach DHCP server on interface en0.”I have a Macronix PCI ethernet adatper, and I am using driver “io-net -d
tulip -p tcpip”.Can anyone help me please?
\
xinni <xiahnisong2001@rogers.com> wrote:
I installed 6.2.1NC, but I cannot have the ethernet card running: when I
configure the en0 to use DHCP, I got an pop-up message “netmanager
error:could not configure DHCP on interface en0. netmanager error: couldnot
reach DHCP server on interface en0.”I have a Macronix PCI ethernet adatper, and I am using driver “io-net -d
tulip -p tcpip”.Can anyone help me please?
Care to post the output from nicinfo once you have started io-net?
chris
–
Chris McKillop <cdm@qnx.com> “The faster I go, the behinder I get.”
Software Engineer, QSSL – Lewis Carroll –
http://qnx.wox.org/
Hi,
Here’s the output from nicinfo:
Tulip: Macronix 98715 Ethernet Controller
Physical Node
ID…0080C6
E544AB
Current Physical Node
ID…0080C6 E544AB
Media
Rate…
…100.00 Mb/s half-duplex UTP
MTU…
…1514
Lan…
…0
I/O Port
Range…0
x7000 - >0x70FF
Hardware
Interrupt…0xA
Promiscuous…
…Disabled
Multicast…
…Enabled
Total Packets Txd
OK…18
Total Packets Txd
Bad…0
Total Packets Rxd
OK…1284
Total Packets Rxd
Bad…0
Total Bytes
Txd…3762
Total Bytes
Rxd…82474
Tx Collision
Errors…0
Tx Collision
Errors(aborted)…0
Carrier Sense lost on
Tx…0
FIFO underruns during
Tx…0
Tx
deferred…
…0
Out of window
collision…0
FIFO underruns during
Rx…0
Allignment
Errors…0
CRC
Errors…
…0
Thanks!
“Chris McKillop” <cdm@qnx.com> wrote in message
news:bgfh8a$ekn$1@nntp.qnx.com…
xinni <> xiahnisong2001@rogers.com> > wrote:
I installed 6.2.1NC, but I cannot have the ethernet card running: when I
configure the en0 to use DHCP, I got an pop-up message “netmanager
error:could not configure DHCP on interface en0. netmanager error:
couldnot
reach DHCP server on interface en0.”I have a Macronix PCI ethernet adatper, and I am using driver “io-net -d
tulip -p tcpip”.Can anyone help me please?
Care to post the output from nicinfo once you have started io-net?chris
–
Chris McKillop <> cdm@qnx.com> > “The faster I go, the behinder I get.”
Software Engineer, QSSL – Lewis Carroll –
http://qnx.wox.org/