Hi
We have an embede Board with an SiS603 Chipset here. We two Problems
with Chipset together with QNX:
a) The GUI only runs in SVGA @60Hz … minor problem since we actually
don’t use the GUI
b) The Networkcard is only detected with a MAC of 00:00:00:00:00:00:00
which is a bigger problem, because our new Switch rejects this MAC
address. Also the NC is only detected with Half-Duplux 10MBit
The Hardware runs fine under Linux (Knoppix). Is there anyone who can
help us?
thanks allot
jan rüdiger
Hi
Sorry it is a SiS630ET Chipset.
jan
There is an updated driver for this chipset, but in the mean time you can
specify the ‘mac=xxxxxxxxxxxx’ on the command line to the driver.
“Jan Rüdiger” <ruediger@uni-mannheim.de> wrote in message
news:bnm0o8$d66$1@inn.qnx.com…
Hi
We have an embede Board with an SiS603 Chipset here. We two Problems
with Chipset together with QNX:a) The GUI only runs in SVGA @60Hz … minor problem since we actually
don’t use the GUIb) The Networkcard is only detected with a MAC of 00:00:00:00:00:00:00
which is a bigger problem, because our new Switch rejects this MAC
address. Also the NC is only detected with Half-Duplux 10MBitsnip
en1: flags=8842<BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
address: 00:00:00:00:00:00
media: Ethernet 10baseT half-duplex
status: active
/snipThe Hardware runs fine under Linux (Knoppix). Is there anyone who can
help us?thanks allot
jan rüdiger
In the next release of the OS there will be a graphics
driver for the SiS630. However, we do not have an SiS630ET
system here so I cannot guarantee the driver will be compatible.
Jan R?diger <ruediger@uni-mannheim.de> wrote:
Hi
We have an embede Board with an SiS603 Chipset here. We two Problems
with Chipset together with QNX:a) The GUI only runs in SVGA @60Hz … minor problem since we actually
don’t use the GUIb) The Networkcard is only detected with a MAC of 00:00:00:00:00:00:00
which is a bigger problem, because our new Switch rejects this MAC
address. Also the NC is only detected with Half-Duplux 10MBitsnip
en1: flags=8842<BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
address: 00:00:00:00:00:00
media: Ethernet 10baseT half-duplex
status: active
/snipThe Hardware runs fine under Linux (Knoppix). Is there anyone who can
help us?thanks allot
jan rüdiger
Hi
Hugh Brown wrote:
There is an updated driver for this chipset, but in the mean time you can
specify the ‘mac=xxxxxxxxxxxx’ on the command line to the driver.
Thanks for your answer, but how do i add command lines to the driver. I
looked into /etc/system/enum/devices
but couldn’t finde the part where the nic is configured. Also there is
noc resMgr running for my nics
thanks
jan rüdiger
You can either do this on the command line, or in your rc.local file.
slay io-net
io-net -dsis9 mac=xxxxxxxxxxxx -ptcpip
ifconfig en0 xx.xx.xx.xx
or
dhcp.client
“Jan Rüdiger” <ruediger@uni-mannheim.de> wrote in message
news:3FA23A93.2020501@uni-mannheim.de…
Hi
Hugh Brown wrote:
There is an updated driver for this chipset, but in the mean time you
can
specify the ‘mac=xxxxxxxxxxxx’ on the command line to the driver.Thanks for your answer, but how do i add command lines to the driver. I
looked into /etc/system/enum/devices
but couldn’t finde the part where the nic is configured. Also there is
noc resMgr running for my nicsthanks
jan rüdiger