I have seriously problem with Photon1.14 Patch D on PC with ChipSet
Intel82845.
The Last Photon Graphics Update with Pg.i830 is installed properly according
Graphics drivers
Release Notes Date of this edition: March 08, 2005
About driver chksum: 3179089267 195848 Pg.i830
About PC Hardware
show_pci :
…
Vendor ID = 8086h, INTEL CORPORATION
Device ID = 2562h,
PCI index = 0h
Class Code = 030000h Display (VGA) ProgIF=0
Revision ID = 3h
Bus number = 0
Device number = 2
Function num = 0
Status Reg = 90h
Command Reg = 7h
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Base Address = MEM@e0000000h,Prefetchable,32bit length 134217728
MEM@e8100000h,32bit length 524288
Subsystem Vendor ID = 1458h
Subsystem ID = 2562h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = 1, INT A
Interrupt line = 5
Capabilities Pointer = d0h
Capability ID = 1h
Capabilities = 21h - 0h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 01 00 21 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 0a 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 8e 1f 00 00
…
In crt.1 I write in the first string:
Null.ms;Pg.i830 -g1280x1024x8 -d0x8086,0x2562 -I0 -R60 -HNqnx/crt;#1280,1024,8,200,0CBDr,i830
- Intel 82830
But after Photon start I have only Black Screen on monitor and message from
monitor:
No Signal Input or
Cable Disconnected…
Photon is working only on Pg.flat driver.
QNX6.3.0 Run with this ChipSet without any problem :
io-graphics -di830 -vid=0x8086,did=0x2562, index=0, photon, xres=1280,
yres=1024, refresh=60, -pphoton hwcursor
working nice!
Whot I have to do in QNX4, becose our progect working only on QNX4 for
today?
Thank you.