installation problems neo-magic & yamaha sound chip

Ramin_Assadollahi · September 6, 2001, 8:27am

hi,

yesterday i tried to install qnx rtp 6.1.

under 6.0 the neomagic graphic card was recognised and
installed correctly. under 6.1 however it is only recognised,
the first boot tells me, that the resolution is not ok 600x800x4,
if i change to 1024x768x(16,24) then the graphic output hangs,
even when i just click ‘test’.
after the second boot, i can see the graphic card setup, i see
vga, vesa, vesa 90, neomagic, neomagic 90.
nothing else than vga works and this only under 600x800x4.

what’s the problem? in the internet i see that the driver hasn’t
changed from 6.0 to 6.1?!

second, the yamaha sound chip (thanks for the driver!) does
not work correctly: it plays just the first 500ms or so and
repeats that, independent of mp3 or wav files. i must kill
the processes, the media player does not react.

i have a sony z600ne, pIII, 128mb ram. tried bios non-p’n’p os,
didn’t help.

what to do?

thanks a lot

ramin

Hardware_Support_Acc · September 6, 2001, 3:12pm

Hi Ramin,

Could you please post (in text) the output of pci -vvv

Thanks

E.

Ramin Assadollahi <assadollahi@exb.de> wrote:

hi,

yesterday i tried to install qnx rtp 6.1.

under 6.0 the neomagic graphic card was recognised and
installed correctly. under 6.1 however it is only recognised,
the first boot tells me, that the resolution is not ok 600x800x4,
if i change to 1024x768x(16,24) then the graphic output hangs,
even when i just click ‘test’.
after the second boot, i can see the graphic card setup, i see
vga, vesa, vesa 90, neomagic, neomagic 90.
nothing else than vga works and this only under 600x800x4.

what’s the problem? in the internet i see that the driver hasn’t
changed from 6.0 to 6.1?!

second, the yamaha sound chip (thanks for the driver!) does
not work correctly: it plays just the first 500ms or so and
repeats that, independent of mp3 or wav files. i must kill
the processes, the media player does not react.

i have a sony z600ne, pIII, 128mb ram. tried bios non-p’n’p os,
didn’t help.

what to do?

thanks a lot

ramin

Ramin_Assadollahi · September 6, 2001, 3:27pm

here it is.
in the meantime i tried io-graphics with the neomagic driver, no mode worked

PCI version = 2.10

Class = Bridge (Host/PCI)
Vendor ID = 8086h, Intel Corporation
Device ID = 7190h, 82443BX/ZX 440BX/ZX AGPset Host Bridge
PCI index = 0h
Class Codes = 060000h
Revision ID = 3h
Bus number = 0
Device number = 0
Function num = 0
Status Reg = 2210h
Command Reg = 106h
I/O space access disabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents enabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
Subsystem Vendor ID = 104dh
Subsystem ID = 807dh
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Capabilities Pointer = a0h
Capability ID = 2h
Capabilities = 10h - 1f000203h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 0c 80 00 00 00 00 00 09 03 10 11 01 00 30 00 11
0x60: 08 10 10 10 10 10 10 10 00 0a c0 00 00 a0 00 00
0x70: 20 1f 0a 38 05 00 03 01 26 03 9c 34 10 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 04 61 00 00 00 05 00 00 00 00 00 00
0xA0: 02 00 10 00 03 02 00 1f 01 03 00 00 00 00 00 00
0xB0: 80 00 00 00 3c 00 00 00 00 00 00 00 20 10 00 00
0xC0: 00 00 00 00 00 00 00 00 18 0c ff ff 7f 00 00 00
0xD0: 00 00 00 00 00 00 00 00 0c 00 00 00 00 00 00 00
0xE0: 4c ad ff bb 8a 3e 00 80 2c d3 f7 cf 9d 3e 00 00
0xF0: 40 01 00 00 00 f8 00 60 20 0f 00 00 00 00 00 00

Class = Bridge (PCI/PCI)
Vendor ID = 8086h, Intel Corporation
Device ID = 7191h, 82443BX/ZX 440BX/ZX AGPset PCI-to-PCI bridge
PCI index = 0h
Class Codes = 060400h
Revision ID = 3h
Bus number = 0
Device number = 1
Function num = 0
Status Reg = 220h
Command Reg = 1fh
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations monitor
Memory Write and Invalidate enabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 1h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 80h
Cache Line Size= 0h
Primary Bus Number = 0h
Secondary Bus Number = 1h
Subordinate Bus Number = 1h
Secondary Latency Timer = 40h
I/O Base = f0h
I/O Limit = 0h
Secondary Status = 22a0h
Memory Base = fe40h
Memory Limit = feb0h
Prefetchable Memory Base = fc00h
Prefetchable Memory Limit= fdf0h
Prefetchable Base Upper 32 Bits = 0h
Prefetchable Limit Upper 32 Bits = 0h
I/O Base Upper 16 Bits = ffffh
I/O Limit Upper 16 Bits = ffffh
Bridge Control = 140ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 8c 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Bridge (PCI/ISA)
Vendor ID = 8086h, Intel Corporation
Device ID = 7110h, 82371AB/EB PIIX4 ISA Bridge
PCI index = 0h
Class Codes = 060100h
Revision ID = 2h
Bus number = 0
Device number = 7
Function num = 0
Status Reg = 280h
Command Reg = fh
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations monitor
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 4d 00 b3 04
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 09 80 80 80 12 00 00 00 00 f2 80 00 00 00 00 00
0x70: 00 00 00 00 00 00 0c 0c 00 00 00 00 00 00 00 00
0x80: 00 00 07 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 04 11 51 71 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 25 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00

Class = Mass Storage (IDE)
Vendor ID = 8086h, Intel Corporation
Device ID = 7111h, 82371AB/EB PIIX4 IDE Controller
PCI index = 0h
Class Codes = 010180h
Revision ID = 1h
Bus number = 0
Device number = 7
Function num = 1
Status Reg = 280h
Command Reg = 5h
I/O space access enabled
Memory space access disabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
PCI IO Address = fcb0h length 16 enabled
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 07 a3 00 80 00 00 00 00 01 00 02 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00

Class = Serial Bus (Universal Serial Bus)
Vendor ID = 8086h, Intel Corporation
Device ID = 7112h, 82371AB/EB PIIX4 USB Interface
PCI index = 0h
Class Codes = 0c0300h
Revision ID = 1h
Bus number = 0
Device number = 7
Function num = 2
Status Reg = 280h
Command Reg = 5h
I/O space access enabled
Memory space access disabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
PCI IO Address = fc60h length 32 enabled
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = INT D
Interrupt line = no connection
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00

Class = Bridge (Unknown)
Vendor ID = 8086h, Intel Corporation
Device ID = 7113h, 82371AB/EB PIIX4 Power Management Controller
PCI index = 0h
Class Codes = 068000h
Revision ID = 3h
Bus number = 0
Device number = 7
Function num = 3
Status Reg = 280h
Command Reg = 3h
I/O space access enabled
Memory space access enabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 01 80 00 00 0f ff bf ff 3f 39 00 00 00 10 00 0a
0x50: 00 40 1c 00 ff 3f 00 00 15 80 00 02 00 00 00 00
0x60: 80 00 c0 02 00 00 00 00 40 80 13 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 98 03 11 00 98 03 11 00
0x80: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 41 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00

Class = Serial Bus (FireWire)
Vendor ID = 104dh, Sony Corporation
Device ID = 8039h, CXD3222 OHCI i.LINK (IEEE 1394) PCI Host Ctrlr
PCI index = 0h
Class Codes = 0c0010h
Revision ID = 2h
Bus number = 0
Device number = 8
Function num = 0
Status Reg = 210h
Command Reg = 0h
I/O space access disabled
Memory space access disabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 8h un-cacheable
Subsystem Vendor ID = 104dh
Subsystem ID = 8080h
Max Lat = 4ns
Min Gnt = 4ns
PCI Int Pin = INT A
Interrupt line = no connection
Capabilities Pointer = dch
Capability ID = 1h
Capabilities = 1h - 0h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 01 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Multimedia (Audio)
Vendor ID = 1073h, Yamaha Corporation
Device ID = 10h, YMF744B DS-1S PCI audio controller
PCI index = 0h
Class Codes = 040100h
Revision ID = 2h
Bus number = 0
Device number = 9
Function num = 0
Status Reg = 210h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
PCI Mem Address = fecf0000h 32bit length 32768 enabled
PCI IO Address = fc00h length 64 enabled
PCI IO Address = fcach length 4 enabled
Subsystem Vendor ID = 104dh
Subsystem ID = 8081h
Max Lat = 25ns
Min Gnt = 5ns
PCI Int Pin = INT A
Interrupt line = 9
Capabilities Pointer = 50h
Capability ID = 1h
Capabilities = 401h - 3h
Device Dependent Registers:
0x40: 5b 00 00 00 4d 10 81 80 08 00 00 00 00 00 00 00
0x50: 01 00 01 04 03 00 00 00 00 00 00 00 00 00 00 00
0x60: 88 03 20 02 30 03 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Communication (Unknown)
Vendor ID = 14f1h, Conexant Systems, Inc.
Device ID = 2443h, SoftK56 Data,Fax PCI Modem
PCI index = 0h
Class Codes = 078000h
Revision ID = 1h
Bus number = 0
Device number = 10
Function num = 0
Status Reg = 290h
Command Reg = 0h
I/O space access disabled
Memory space access disabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
PCI IO Address = 0h length 8 disabled
Subsystem Vendor ID = 104dh
Subsystem ID = 8083h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = INT A
Interrupt line = no connection
Capabilities Pointer = 40h
Capability ID = 1h
Capabilities = c822h - 3h
Device Dependent Registers:
0x40: 01 00 22 c8 03 00 00 00 42 12 01 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Network (Ethernet)
Vendor ID = 8086h, Intel Corporation
Device ID = 1229h, 82557/8/9 Fast Ethernet LAN Controller
PCI index = 0h
Class Codes = 020000h
Revision ID = 8h
Bus number = 0
Device number = 11
Function num = 0
Status Reg = 290h
Command Reg = 17h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate enabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 42h
Cache Line Size= 8h un-cacheable
PCI Mem Address = fecff000h 32bit length 4096 enabled
PCI IO Address = fcc0h length 64 enabled
PCI Mem Address = fed00000h 32bit length 1048576 enabled
Subsystem Vendor ID = 104dh
Subsystem ID = 8084h
Max Lat = 56ns
Min Gnt = 8ns
PCI Int Pin = INT A
Interrupt line = 9
Capabilities Pointer = dch
Capability ID = 1h
Capabilities = 7e22h - 3a004103h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 22 7e
0xE0: 03 41 00 3a 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Bridge (CardBus)
Vendor ID = 1180h, Ricoh Co Ltd
Device ID = 475h, RL5C475 CardBus controller
PCI index = 0h
Class Codes = 060700h
Revision ID = 80h
Bus number = 0
Device number = 12
Function num = 0
Status Reg = 210h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
ExCA Base Address = ffeff000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 2
Subordinate Bus Number = 2
Secondary Latency Timer = 20h
Memory Base 0 = 0h
Memory Limit 0 = 0h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 0h
I/O Limit 0 = 0h
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 9
Bridge Control = 780h
Subsystem Vendor ID = 104dh
Subsystem ID = 8082h
Legacy Mode Base Address = 3e0h
System Control = 20001h
Retry Status = 0h
Card Control = 0h
Device Control = 0h
Buffer Control = 0h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 4d 10 82 80 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 01 00 02 00 00 00 00 00 63 04 63 04 00 00 00 30
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 4d 10 82 80 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 19 fe
0xE0: 00 41 c0 24 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Memory (Flash)
Vendor ID = 104dh, Sony Corporation
Device ID = 808ah, Unknown Unknown
PCI index = 0h
Class Codes = 050100h
Revision ID = 1h
Bus number = 0
Device number = 13
Function num = 0
Status Reg = 210h
Command Reg = 0h
I/O space access disabled
Memory space access disabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
Subsystem Vendor ID = 104dh
Subsystem ID = 8085h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = INT A
Interrupt line = 0
Capabilities Pointer = dch
Capability ID = 1h
Capabilities = 2h - 3h
Device Dependent Registers:
0x40: 00 00 00 00 4d 10 85 80 00 00 01 05 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 02 00
0xE0: 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Display (VGA)
Vendor ID = 10c8h, Neomagic Corporation
Device ID = 16h, NM2380 MagicMedia 256XL+
PCI index = 0h
Class Codes = 030000h
Revision ID = 10h
Bus number = 1
Device number = 0
Function num = 0
Status Reg = 290h
Command Reg = 207h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 80h
Cache Line Size= 0h
PCI Mem Address = fc000000h prefetchable 32bit length 33554432 enabled
PCI Mem Address = fe400000h 32bit length 4194304 enabled
PCI Mem Address = feb00000h 32bit length 1048576 enabled
Subsystem Vendor ID = 104dh
Subsystem ID = 809dh
Max Lat = 255ns
Min Gnt = 16ns
PCI Int Pin = INT A
Interrupt line = 9
Capabilities Pointer = d0h
Capability ID = 2h
Capabilities = 10h - 7000201h
Capability ID = 1h
Capabilities = 621h - 0h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 02 dc 10 00 01 02 00 07 01 03 00 07 01 00 21 06
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

“Hardware Support Account” <hw@qnx.com> schrieb im Newsbeitrag
news:9n83pj$lsr$3@nntp.qnx.com…

Hi Ramin,

Could you please post (in text) the output of pci -vvv

Thanks

E.

Ramin Assadollahi <> assadollahi@exb.de> > wrote:
hi,

yesterday i tried to install qnx rtp 6.1.

under 6.0 the neomagic graphic card was recognised and
installed correctly. under 6.1 however it is only recognised,
the first boot tells me, that the resolution is not ok 600x800x4,
if i change to 1024x768x(16,24) then the graphic output hangs,
even when i just click ‘test’.
after the second boot, i can see the graphic card setup, i see
vga, vesa, vesa 90, neomagic, neomagic 90.
nothing else than vga works and this only under 600x800x4.

what’s the problem? in the internet i see that the driver hasn’t
changed from 6.0 to 6.1?!

second, the yamaha sound chip (thanks for the driver!) does
not work correctly: it plays just the first 500ms or so and
repeats that, independent of mp3 or wav files. i must kill
the processes, the media player does not react.

i have a sony z600ne, pIII, 128mb ram. tried bios non-p’n’p os,
didn’t help.

what to do?

thanks a lot

ramin

Hardware_Support_Acc · September 6, 2001, 3:29pm

Please post the output of pci -vvv on the newsgroups.

Thanks

E.

Ramin Assadollahi <assadollahi@exb.de> wrote:

hi,

yesterday i tried to install qnx rtp 6.1.

under 6.0 the neomagic graphic card was recognised and
installed correctly. under 6.1 however it is only recognised,
the first boot tells me, that the resolution is not ok 600x800x4,
if i change to 1024x768x(16,24) then the graphic output hangs,
even when i just click ‘test’.
after the second boot, i can see the graphic card setup, i see
vga, vesa, vesa 90, neomagic, neomagic 90.
nothing else than vga works and this only under 600x800x4.

what’s the problem? in the internet i see that the driver hasn’t
changed from 6.0 to 6.1?!

second, the yamaha sound chip (thanks for the driver!) does
not work correctly: it plays just the first 500ms or so and
repeats that, independent of mp3 or wav files. i must kill
the processes, the media player does not react.

i have a sony z600ne, pIII, 128mb ram. tried bios non-p’n’p os,
didn’t help.

what to do?

thanks a lot

ramin

Hardware_Support_Acc · September 6, 2001, 6:49pm

Hi Ramin,

Thanks!

Could you please try the latest pci-bios from developers.qnx.com
and post here if it helps or not.

Thanks

E.

Ramin Assadollahi <assadollahi@exb.de> wrote:

here it is.
in the meantime i tried io-graphics with the neomagic driver, no mode worked

PCI version = 2.10

Class = Bridge (Host/PCI)
Vendor ID = 8086h, Intel Corporation
Device ID = 7190h, 82443BX/ZX 440BX/ZX AGPset Host Bridge
PCI index = 0h
Class Codes = 060000h
Revision ID = 3h
Bus number = 0
Device number = 0
Function num = 0
Status Reg = 2210h
Command Reg = 106h
I/O space access disabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents enabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
Subsystem Vendor ID = 104dh
Subsystem ID = 807dh
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Capabilities Pointer = a0h
Capability ID = 2h
Capabilities = 10h - 1f000203h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 0c 80 00 00 00 00 00 09 03 10 11 01 00 30 00 11
0x60: 08 10 10 10 10 10 10 10 00 0a c0 00 00 a0 00 00
0x70: 20 1f 0a 38 05 00 03 01 26 03 9c 34 10 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 04 61 00 00 00 05 00 00 00 00 00 00
0xA0: 02 00 10 00 03 02 00 1f 01 03 00 00 00 00 00 00
0xB0: 80 00 00 00 3c 00 00 00 00 00 00 00 20 10 00 00
0xC0: 00 00 00 00 00 00 00 00 18 0c ff ff 7f 00 00 00
0xD0: 00 00 00 00 00 00 00 00 0c 00 00 00 00 00 00 00
0xE0: 4c ad ff bb 8a 3e 00 80 2c d3 f7 cf 9d 3e 00 00
0xF0: 40 01 00 00 00 f8 00 60 20 0f 00 00 00 00 00 00

Class = Bridge (PCI/PCI)
Vendor ID = 8086h, Intel Corporation
Device ID = 7191h, 82443BX/ZX 440BX/ZX AGPset PCI-to-PCI bridge
PCI index = 0h
Class Codes = 060400h
Revision ID = 3h
Bus number = 0
Device number = 1
Function num = 0
Status Reg = 220h
Command Reg = 1fh
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations monitor
Memory Write and Invalidate enabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 1h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 80h
Cache Line Size= 0h
Primary Bus Number = 0h
Secondary Bus Number = 1h
Subordinate Bus Number = 1h
Secondary Latency Timer = 40h
I/O Base = f0h
I/O Limit = 0h
Secondary Status = 22a0h
Memory Base = fe40h
Memory Limit = feb0h
Prefetchable Memory Base = fc00h
Prefetchable Memory Limit= fdf0h
Prefetchable Base Upper 32 Bits = 0h
Prefetchable Limit Upper 32 Bits = 0h
I/O Base Upper 16 Bits = ffffh
I/O Limit Upper 16 Bits = ffffh
Bridge Control = 140ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 8c 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Bridge (PCI/ISA)
Vendor ID = 8086h, Intel Corporation
Device ID = 7110h, 82371AB/EB PIIX4 ISA Bridge
PCI index = 0h
Class Codes = 060100h
Revision ID = 2h
Bus number = 0
Device number = 7
Function num = 0
Status Reg = 280h
Command Reg = fh
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations monitor
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Multi-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 4d 00 b3 04
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 09 80 80 80 12 00 00 00 00 f2 80 00 00 00 00 00
0x70: 00 00 00 00 00 00 0c 0c 00 00 00 00 00 00 00 00
0x80: 00 00 07 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 04 11 51 71 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 25 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00

Class = Mass Storage (IDE)
Vendor ID = 8086h, Intel Corporation
Device ID = 7111h, 82371AB/EB PIIX4 IDE Controller
PCI index = 0h
Class Codes = 010180h
Revision ID = 1h
Bus number = 0
Device number = 7
Function num = 1
Status Reg = 280h
Command Reg = 5h
I/O space access enabled
Memory space access disabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
PCI IO Address = fcb0h length 16 enabled
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 07 a3 00 80 00 00 00 00 01 00 02 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00

Class = Serial Bus (Universal Serial Bus)
Vendor ID = 8086h, Intel Corporation
Device ID = 7112h, 82371AB/EB PIIX4 USB Interface
PCI index = 0h
Class Codes = 0c0300h
Revision ID = 1h
Bus number = 0
Device number = 7
Function num = 2
Status Reg = 280h
Command Reg = 5h
I/O space access enabled
Memory space access disabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
PCI IO Address = fc60h length 32 enabled
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = INT D
Interrupt line = no connection
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00

Class = Bridge (Unknown)
Vendor ID = 8086h, Intel Corporation
Device ID = 7113h, 82371AB/EB PIIX4 Power Management Controller
PCI index = 0h
Class Codes = 068000h
Revision ID = 3h
Bus number = 0
Device number = 7
Function num = 3
Status Reg = 280h
Command Reg = 3h
I/O space access enabled
Memory space access enabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 0h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = NC
Interrupt line = 0
Device Dependent Registers:
0x40: 01 80 00 00 0f ff bf ff 3f 39 00 00 00 10 00 0a
0x50: 00 40 1c 00 ff 3f 00 00 15 80 00 02 00 00 00 00
0x60: 80 00 c0 02 00 00 00 00 40 80 13 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 98 03 11 00 98 03 11 00
0x80: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 41 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 30 0f 00 00 00 00 00 00

Class = Serial Bus (FireWire)
Vendor ID = 104dh, Sony Corporation
Device ID = 8039h, CXD3222 OHCI i.LINK (IEEE 1394) PCI Host Ctrlr
PCI index = 0h
Class Codes = 0c0010h
Revision ID = 2h
Bus number = 0
Device number = 8
Function num = 0
Status Reg = 210h
Command Reg = 0h
I/O space access disabled
Memory space access disabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 8h un-cacheable
Subsystem Vendor ID = 104dh
Subsystem ID = 8080h
Max Lat = 4ns
Min Gnt = 4ns
PCI Int Pin = INT A
Interrupt line = no connection
Capabilities Pointer = dch
Capability ID = 1h
Capabilities = 1h - 0h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 01 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Multimedia (Audio)
Vendor ID = 1073h, Yamaha Corporation
Device ID = 10h, YMF744B DS-1S PCI audio controller
PCI index = 0h
Class Codes = 040100h
Revision ID = 2h
Bus number = 0
Device number = 9
Function num = 0
Status Reg = 210h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
PCI Mem Address = fecf0000h 32bit length 32768 enabled
PCI IO Address = fc00h length 64 enabled
PCI IO Address = fcach length 4 enabled
Subsystem Vendor ID = 104dh
Subsystem ID = 8081h
Max Lat = 25ns
Min Gnt = 5ns
PCI Int Pin = INT A
Interrupt line = 9
Capabilities Pointer = 50h
Capability ID = 1h
Capabilities = 401h - 3h
Device Dependent Registers:
0x40: 5b 00 00 00 4d 10 81 80 08 00 00 00 00 00 00 00
0x50: 01 00 01 04 03 00 00 00 00 00 00 00 00 00 00 00
0x60: 88 03 20 02 30 03 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Communication (Unknown)
Vendor ID = 14f1h, Conexant Systems, Inc.
Device ID = 2443h, SoftK56 Data,Fax PCI Modem
PCI index = 0h
Class Codes = 078000h
Revision ID = 1h
Bus number = 0
Device number = 10
Function num = 0
Status Reg = 290h
Command Reg = 0h
I/O space access disabled
Memory space access disabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 40h
Cache Line Size= 0h
PCI IO Address = 0h length 8 disabled
Subsystem Vendor ID = 104dh
Subsystem ID = 8083h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = INT A
Interrupt line = no connection
Capabilities Pointer = 40h
Capability ID = 1h
Capabilities = c822h - 3h
Device Dependent Registers:
0x40: 01 00 22 c8 03 00 00 00 42 12 01 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Network (Ethernet)
Vendor ID = 8086h, Intel Corporation
Device ID = 1229h, 82557/8/9 Fast Ethernet LAN Controller
PCI index = 0h
Class Codes = 020000h
Revision ID = 8h
Bus number = 0
Device number = 11
Function num = 0
Status Reg = 290h
Command Reg = 17h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate enabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 42h
Cache Line Size= 8h un-cacheable
PCI Mem Address = fecff000h 32bit length 4096 enabled
PCI IO Address = fcc0h length 64 enabled
PCI Mem Address = fed00000h 32bit length 1048576 enabled
Subsystem Vendor ID = 104dh
Subsystem ID = 8084h
Max Lat = 56ns
Min Gnt = 8ns
PCI Int Pin = INT A
Interrupt line = 9
Capabilities Pointer = dch
Capability ID = 1h
Capabilities = 7e22h - 3a004103h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 22 7e
0xE0: 03 41 00 3a 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Bridge (CardBus)
Vendor ID = 1180h, Ricoh Co Ltd
Device ID = 475h, RL5C475 CardBus controller
PCI index = 0h
Class Codes = 060700h
Revision ID = 80h
Bus number = 0
Device number = 12
Function num = 0
Status Reg = 210h
Command Reg = 7h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 2h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
ExCA Base Address = ffeff000h
Capabilities Pointer = ffh
Secondary Status = ffffh
Primary Bus Number = 0
Secondary Bus Number = 2
Subordinate Bus Number = 2
Secondary Latency Timer = 20h
Memory Base 0 = 0h
Memory Limit 0 = 0h
Memory Base 1 = 0h
Memory Limit 1 = 0h
I/O Base 0 = 0h
I/O Limit 0 = 0h
I/O Base 1 = 0h
I/O Limit 1 = 0h
PCI Int Pin = 1
PCI Int Pin = INT A
Interrupt line = 9
Bridge Control = 780h
Subsystem Vendor ID = 104dh
Subsystem ID = 8082h
Legacy Mode Base Address = 3e0h
System Control = 20001h
Retry Status = 0h
Card Control = 0h
Device Control = 0h
Buffer Control = 0h
Socket DMA Register 0 = 0h
Socket DMA Register 1 = 0h
Device Dependent Registers:
0x40: 4d 10 82 80 e1 03 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 01 00 02 00 00 00 00 00 63 04 63 04 00 00 00 30
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 4d 10 82 80 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 19 fe
0xE0: 00 41 c0 24 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Memory (Flash)
Vendor ID = 104dh, Sony Corporation
Device ID = 808ah, Unknown Unknown
PCI index = 0h
Class Codes = 050100h
Revision ID = 1h
Bus number = 0
Device number = 13
Function num = 0
Status Reg = 210h
Command Reg = 0h
I/O space access disabled
Memory space access disabled
Bus Master disabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 20h
Cache Line Size= 0h
Subsystem Vendor ID = 104dh
Subsystem ID = 8085h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = INT A
Interrupt line = 0
Capabilities Pointer = dch
Capability ID = 1h
Capabilities = 2h - 3h
Device Dependent Registers:
0x40: 00 00 00 00 4d 10 85 80 00 00 01 05 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 02 00
0xE0: 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Class = Display (VGA)
Vendor ID = 10c8h, Neomagic Corporation
Device ID = 16h, NM2380 MagicMedia 256XL+
PCI index = 0h
Class Codes = 030000h
Revision ID = 10h
Bus number = 1
Device number = 0
Function num = 0
Status Reg = 290h
Command Reg = 207h
I/O space access enabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Checking disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 80h
Cache Line Size= 0h
PCI Mem Address = fc000000h prefetchable 32bit length 33554432 enabled
PCI Mem Address = fe400000h 32bit length 4194304 enabled
PCI Mem Address = feb00000h 32bit length 1048576 enabled
Subsystem Vendor ID = 104dh
Subsystem ID = 809dh
Max Lat = 255ns
Min Gnt = 16ns
PCI Int Pin = INT A
Interrupt line = 9
Capabilities Pointer = d0h
Capability ID = 2h
Capabilities = 10h - 7000201h
Capability ID = 1h
Capabilities = 621h - 0h
Device Dependent Registers:
0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xA0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xB0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xC0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xD0: 02 dc 10 00 01 02 00 07 01 03 00 07 01 00 21 06
0xE0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0xF0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

“Hardware Support Account” <> hw@qnx.com> > schrieb im Newsbeitrag
news:9n83pj$lsr$> 3@nntp.qnx.com> …
Hi Ramin,

Could you please post (in text) the output of pci -vvv

Thanks

E.

Ramin Assadollahi <> assadollahi@exb.de> > wrote:
hi,

yesterday i tried to install qnx rtp 6.1.

under 6.0 the neomagic graphic card was recognised and
installed correctly. under 6.1 however it is only recognised,
the first boot tells me, that the resolution is not ok 600x800x4,
if i change to 1024x768x(16,24) then the graphic output hangs,
even when i just click ‘test’.
after the second boot, i can see the graphic card setup, i see
vga, vesa, vesa 90, neomagic, neomagic 90.
nothing else than vga works and this only under 600x800x4.

what’s the problem? in the internet i see that the driver hasn’t
changed from 6.0 to 6.1?!

second, the yamaha sound chip (thanks for the driver!) does
not work correctly: it plays just the first 500ms or so and
repeats that, independent of mp3 or wav files. i must kill
the processes, the media player does not react.

i have a sony z600ne, pIII, 128mb ram. tried bios non-p’n’p os,
didn’t help.

what to do?

thanks a lot

ramin

Ramin_Assadollahi · September 7, 2001, 8:18am

sir,

i am not really sure how to do this, what i have done is:

downloaded pci-bios at developers.qnx.com/.../fixes

and changed the version that i found in /sbin

rebooted, and: nothing changed.

ist that ok? or do i have to rebuild bootfile?

cheers,

ramin

Hardware_Support_Acc · September 7, 2001, 3:32pm

Well you could slay pci-bios then restart it spcifying the path
to the newer one

slay pci-bios
./whateverpath/pci-bios &

Then start Photon.

E.

Ramin Assadollahi <assadollahi@exb.de> wrote:

sir,

i am not really sure how to do this, what i have done is:

downloaded pci-bios at developers.qnx.com/.../fixes

and changed the version that i found in /sbin

rebooted, and: nothing changed.

ist that ok? or do i have to rebuild bootfile?

cheers,

ramin

Ramin_Assadollahi · September 7, 2001, 4:14pm

hi,

i only have the standard boot image
that directly runs photon after start.
while running photon i started a term
then slayed pci-bios and started the
new one. afterwards i went into graphics
setup - same problems as before.

maybe you can send me a boot.build
that is standard but doesnt go into photon?
or, well i dont know.

ram

Hardware_Support_Acc · September 12, 2001, 7:17pm

Hi Ramin,

Regarding the graphics, could you please run the following
script located here:

http://staff.qnx.com/~emuis/files/photon2/utils/grafxscript.rtp

Save the file to your system then as root make it executable:

chmod +x grafxscript.rtp

Then as root (exit out of Photon if it is running) run
the script and send us the file it creates.

Thanks

E.

Ramin Assadollahi <assadollahi@exb.de> wrote:

hi,

i only have the standard boot image
that directly runs photon after start.
while running photon i started a term
then slayed pci-bios and started the
new one. afterwards i went into graphics
setup - same problems as before.

maybe you can send me a boot.build
that is standard but doesnt go into photon?
or, well i dont know.

ram

Ramin_Assadollahi · September 17, 2001, 2:50pm

hi e.

well, i was away for a while, now i’m back.
unfortunately the link below doesn’t work.
i don’t know why.
that’s my first problem, the other, more trivial
one is, that i don’ actually know how to leave
photon. obviously i can’t simply leave it by using
the start menu at the lower left corner. so:
how do i do it?

thanx

ramin

“Hardware Support Account” <hw@qnx.com> schrieb im Newsbeitrag
news:9nocbl$q4r$1@nntp.qnx.com…

Hi Ramin,

Regarding the graphics, could you please run the following
script located here:

http://staff.qnx.com/~emuis/files/photon2/utils/grafxscript.rtp

Save the file to your system then as root make it executable:

chmod +x grafxscript.rtp

Then as root (exit out of Photon if it is running) run
the script and send us the file it creates.

Thanks

ed1k2 · September 17, 2001, 3:18pm

Hi Ramin,

Ramin Assadollahi <assadollahi@exb.de> wrote in article <9o52gk$qp9$1@inn.qnx.com>…

hi e.

well, i was away for a while, now i’m back.
unfortunately the link below doesn’t work.
i don’t know why.
that’s my first problem, the other, more trivial
one is, that i don’ actually know how to leave
photon. obviously i can’t simply leave it by using
the start menu at the lower left corner. so:
how do i do it?

You could exit to text mode from “Welcome” window. Look careful at radio-buttons and other buttons
(I guess the Tab key helps to navigate). Press Shift-Ctrl-Alt-BackSpace in order to leave Photon.
But if you did phlogin it returns to “Welcome” window.
You could create a dummy (empty) file named nophoton.
/etc/system/config/nophoton
Then you boot into text mode after reboot.

Type
#ph
to launch Photon from text mode.

Hope it helps.
Best Regards,
Eduard.

Ramin_Assadollahi · September 17, 2001, 4:20pm

hi ed1k,

well there are no radio buttons, there’s only
the shutdown and the login button.
anyway, the nophoton hint helped, thanx
still don’t have acces to the script in the web

ram

“ed1k” <ed1k@yahoo.com> schrieb im Newsbeitrag
news:01c13f8d$211ef4a0$396fa8c0@ED1K…

Hi Ramin,

Ramin Assadollahi <> assadollahi@exb.de> > wrote in article
9o52gk$qp9$> 1@inn.qnx.com> >…
hi e.

well, i was away for a while, now i’m back.
unfortunately the link below doesn’t work.
i don’t know why.
that’s my first problem, the other, more trivial
one is, that i don’ actually know how to leave
photon. obviously i can’t simply leave it by using
the start menu at the lower left corner. so:
how do i do it?

You could exit to text mode from “Welcome” window. Look careful at
radio-buttons and other buttons
(I guess the Tab key helps to navigate). Press Shift-Ctrl-Alt-BackSpace in
order to leave Photon.
But if you did phlogin it returns to “Welcome” window.
You could create a dummy (empty) file named nophoton.
/etc/system/config/nophoton
Then you boot into text mode after reboot.

Type
#ph
to launch Photon from text mode.

Hope it helps.
Best Regards,
Eduard.

Ramin_Assadollahi · September 17, 2001, 4:21pm

hi,

i still can’t access your script in the web, don’t know?!

cheers
ram

“Hardware Support Account” <hw@qnx.com> schrieb im Newsbeitrag
news:9nocbl$q4r$1@nntp.qnx.com…

Hi Ramin,

Regarding the graphics, could you please run the following
script located here:

http://staff.qnx.com/~emuis/files/photon2/utils/grafxscript.rtp

Save the file to your system then as root make it executable:

chmod +x grafxscript.rtp

Then as root (exit out of Photon if it is running) run
the script and send us the file it creates.

Thanks

E.

Ramin Assadollahi <> assadollahi@exb.de> > wrote:
hi,

i only have the standard boot image
that directly runs photon after start.
while running photon i started a term
then slayed pci-bios and started the
new one. afterwards i went into graphics
setup - same problems as before.

maybe you can send me a boot.build
that is standard but doesnt go into photon?
or, well i dont know.

ram

Hardware_Support_Acc · September 17, 2001, 6:29pm

Hi,

I mailed you the script, can you run it and them post the output here.

Regards,

Joe

Ramin Assadollahi <assadollahi@exb.de> wrote:

hi,

i still can’t access your script in the web, don’t know?!

cheers
ram

“Hardware Support Account” <> hw@qnx.com> > schrieb im Newsbeitrag
news:9nocbl$q4r$> 1@nntp.qnx.com> …
Hi Ramin,

Regarding the graphics, could you please run the following
script located here:

http://staff.qnx.com/~emuis/files/photon2/utils/grafxscript.rtp

Save the file to your system then as root make it executable:

chmod +x grafxscript.rtp

Then as root (exit out of Photon if it is running) run
the script and send us the file it creates.

Thanks

E.

Ramin Assadollahi <> assadollahi@exb.de> > wrote:
hi,

i only have the standard boot image
that directly runs photon after start.
while running photon i started a term
then slayed pci-bios and started the
new one. afterwards i went into graphics
setup - same problems as before.

maybe you can send me a boot.build
that is standard but doesnt go into photon?
or, well i dont know.

ram

ed1k2 · September 18, 2001, 11:36am

Ramin Assadollahi <assadollahi@exb.de> wrote in article <9o57pf$2te$1@inn.qnx.com>…

hi ed1k,

well there are no radio buttons, there’s only
the shutdown and the login button

Hi Ramin,
…
If my memory serves me, you could click on shutdown and then should be the three ways:
Exit to text mode
Reboot computer
Shutdown computer

Cheers,
Eduard.

Ramin_Assadollahi · September 18, 2001, 11:41am

thanx a lot,

the script itself did not really work,
i had to remove the 2>/dev/null lines
another problem was, that crttrap did not write
anything to the textfile, just

/usr/photon/bin/devgt-iographics -dldevg-neomagic.so -I0 -d0x10c8,0x0016 -VV
/usr/photon/bin/devgt-iographics -dldevg-vesabios.so -I0 -d0x10c8,0x0016 -VV
and wrote one file, i think it was graphics-modes

the script didn’t compress the .gnfo files, so
i took them to win and zipped them there
u will find this zipfile attached.

i hope, it gives you the information that you need, anyway.
it would be really cool to start using qnx6.1. i’m
really hot to write my first own programs for it.

cheers ramin

begin 666 grafxinfo.zip
M4$L#! H+IB,BL````````````````,````8W)T=')A<"YG;F9O4$L# M!!0````(`/M6,BM%S4$]1 ```%,````)````9&ES<"YG;F9OTRTJKP`AW0H% M!4.%HOS\$@4P2,K,4T `8Q,3(U,%K](\!2,C!0-3*U-C!?W2XB+]G,PD$$[) M+"XH+<G,T2O.US/B`@!02P,$% ````@`^U8R*YXK7:(L`0``_ 8```D```!D M;&QS+F=N9F^5U&UNPR ,!N#_.P47R K&$*='V"4JTB*"U(8NL*R[_3ZEK9E$ M8HO?CVS\0C.]WCY/<Q-"B2FE(KZJCZ/X+8T6I'AZ&06 D+0'%+MS['>G\WEW M\G-H7(F'R06O@!YS>FBVJ0HM?:M6*-S+I=J[,0_>;Q<!6J"_?9J%>!SB-1^& M^#QS4#101=^F>&-XJE55+Y*2FSFED#[64>-"-E*R1&GLFJ@9H@!LK:R)%W<< M+&X'%77U%B^N3(FQ%*VMAG4P<&9>B<WHT\6%>.20%N]6;1?DY$X^C0S0DEP! M`^/Y*41MJUPJKGAH&=%1FCI8-SM.&J6]3^.2S)J!M:8^<]:'[&;>/9(Q=;-< M&;$11/>_XC]N#FX[AQ*QRI6Q,)KK9%V;?79]3)DS+U UU3_CO@-02P,$% `` M``@`%(VO*DR_@Q6%!@``]S,```D```!E;G5M+F=N9F_5F^UOVC@8P#^W?\6C M=A^*!B7O!>EV$H,6(96M`X;83J?*) Y8"C&+`Z-WNO_]' (M-%DP\2+1?FAI MR._WV(]?8H=P>7X)+>P2GX2$^@Q<&L D0/,IL1DX>$ELS,XO^4EW-)BA$ B# M/_A?>_HG_ 7_/K_^#_Z&/Y =.39OQ/]$;W#XL^\]`?4Q5]/%'*@+\=L,?A+/ M@S&&.0YXZ!EVK@$&P1.$%-9J3@%>\;.Y96Z3ZA+[#B\B"P/B3\ E`0O+0,,I M#GX2AE^8AV8'',+F'GH"VT.,7<<510LO9)']`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`) ; MXH"_RS?#`<\O7;!HRRQ^82H#6XQ3S^#'>58_:(KR:IS?+?A6NXM&(ZFFN+B$ M3?7CRB?\JQ4PS"T.KQGEFVM&@QQ+9D/?&>!=9$\M`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`WH2@%9350Y@9A*[S2#XJ-821$$/ MO!)>EM_0.^W:WH.^4=$_8=I%$V+#^O?Z)J1F6HUA)JT=HM]G![<R\>^C3%K- MID?W!X+KJ7@[2CE?77W/KGGM$'T@N)&)CUK%=!\?TUD4YU2'NZI@M'T0X7F9 MTN%KW^;3& </`0536:T*F@?)A$51?V<E]%]40B^T$KID):[77W38;/^:]XU^ M_['5Z3_<-[Z5UEN_KSZR;>SA>/<WO.TW0+LNZIELMIR@4^FNR/.B(9OV10]P MZ<)WRL"5\X".\?H+,#[U*SRCS]]_*?3CF2,2L,EIOI3M9>1_4$L#!!0````( M`/M6,BL_L9#0/P```$X````(````9F9B+F=N9F_3+2JO`"'="@4%0X6B_/P2 M!3!(RLQ30 !C$P-C0P6OTCP%(R,%`U,K4S,%_=+B(OV<S"003DM+TBO.US/B M`@!02P,$% ````@`^U8R*^ 5^PQ'````50````<```!I;RYG;F9OTRTJKP`A MW0H%!4.%HOS\$@4P2,K,4T `"Q,#(Q,%K](\!2,C!0-+*P,#!?W2XB+]@HS\ MDOP\?:!B_<Q\W?2BQ(*,S.1B+@!02P,$% ````@`_%8R*S[@.Z<J! ``\S$` M``H```!M;V1E<RYG;F9OO5G!;IPP$+WG*RSE"I%A6>HHI[;IH9>J4JM>*\J2 M#>IN6+&;U7Y^;1*;C>TL,]C34Z($\WAOGF'\INW2=5_M'MMZS])U6?!3(?A) ML'2U637'=7I<5S?[CJ7?Y2_%S:[:W%W+BQ)Y45(D&><)3^1_6,KVU4/#MMVJ MN6K=6_+S6SXUW;9:M_5PWZ]<_IV?,EZ+1/XH7V\O;RQ>;O_YTWVB5TB8;_I7 M"T9!*"@@#$M_#A?UW:$Z-+=<7G1WK5 5N@?Y]RV_`.[*!N$HT!Q%!(YB)D>A M!,;442@UT74<(. P7HX#*I_!,>-Y<?I0"CA)M2*1*Y L%<8`%D)3P0[X>)ZY MX"A\250N>1=M2M(!+X3J`#P\`IKK(N>G7!HJ6T*IRA6)7)%D2Q13!:+ H$!> MH@I7X?NP@3Q+-,]R'D\@T&6>Y=QW+;R>^F6+K*=^VP;54[]N\?4T/,'U-#QQ M]30\0^II>,ZN9UY@>>;%+)Y0H(L\?=BP[R?<M_H#BO2M_H(&^59_0O&^-3S! MOC4\<;XU/$-\:WBB?:MYPGVK>2)]JWD&^5;SQ/O6]$1PXYJF".E<TQ4%6=>T M17COCES!YAVYXMP[<@VQ[\@5[5_#%6Y@PQ7I8,,UR,*&ZPP/FWX786+3\")= M/':\038>6]X9/A[YPHT\\L4Y^8QOB)7/^**]//2^$/Q:^M;8,^F"D)!A9QD M%*I"GW>.0;1I(TEL?U_$Z.^+N?W],LM/"X$XF<H%B5R K*6"4% AM52H"AU= M2\T17DM-$EE+S3*HEIKF_-Z>-$X\-OOJ3]OM87'B?:*NEP#/3U5=-YNFET17 M;-6WQZ9G#UW/?GWY\9'E-YRSNMON-FWU=&#5JMH=FGX_&3I>?!A(Z/CR?"^R MQGA$3PD`>@DBO40$O02I7F[,.:&7%7-&U<L-0_%Z66%H;+T\D>F$8'9D&E4Q M3["*E\P.5J-KYHE?IT2SX]>HJOE"6KQL3D@;6S=/E#LAFQWE1E7-$_CB1;,# M7S+-2K1F):5FP,<!A<=4WTRXS^R(F>2K&>0S.X@FTPSL,SNNIM$LQ&=VJ$VE MV5DL`M1,1R DFD$?!Q204_5G\+UIQ^@D'5K0WK3#=C+-P'O3CN1I- O9FW9P M3Z49?&_:\3Z)9D%[TQX"D)T%X)O3&170G :"MJ<S4*#3#;Q!G;$#D6XA6]09 M3I#I!M^DS@B#1K>@;>H,.NC.GXB-ZHQ#B$Z@05O5'9H0:@??K,YHA4J[D.WJ M#F!(SJ+P^,\9T\0]B3K#G!D'T;?#'"J]D&?W@NKL7L0XNQ>T9W<5R2\P^:W* MWQ=$^:UZ$,2PPC]]X9[Y17R]X![3@I%X3"L6Y#$M&97'W!'EA&36B#*N8LX@ M<X9@;P>95'K!/6:/.TD4"_.8-13]#W,[_.CTFM6/3?UW_[QE^6+)LEN69?G5 M/U!+`P04````" #[5C(K9H$IWD\*``!'60``" ```'!C:2YG;F9O[9S=<]JX M%L"?E[]",_<E.[=I+/F3G<D#7^DR&]),:7>[]TW8<O 4;,:8MMF__I[C#S @ M.[:!)MF2H12D<R39ELY/YTBB==\;DJ\B7'J!3^#OFK"W5&FU>C.^7)+UWS7I MAI[S(,C%[\$RN@*E7UM_"M$0C+L9R*68AG3-V3H1V)&>D&X"$(>8;FMOOCJ MV2(G:M*V`J(6TS2U^_GJ?Y^)IBG)A\Z[^Z6("-:35MK"-GJ^([YGZLHT;6 O M<,0R33,4^)NV/D!=\=4DM5T3==KJKI;$7\TG(LP*R)J4I6+2S<JWX_9"8BHU MCG@$NA_$0ZK(&,7*@_F<^TZ6?DVH8DQ;OPROWI/<E@D.QW>+8%-,_QEGPR$T[K MEY&8!^'C=J[PTTQLWH@O(VC(.FV\$+;'X3X^VC-!@H5([N62> ]^$.:*_"OT M(B@26C/TO_*9YW#XNJGXGL]$!"EC/P@6GO^PE06JCZ0W%?:7[9P^C_A5QW%" M;":T:[&C.1Y\^/ ?XH0>])Q<\@U<`YEP^\ME%%SB_R0*N;_D=M+R* !9UQ6A M\"/"'^!]<P]^%]R!LJ+'A<@>,1E#I3-QZ::/I=4=CC^2?)\$F>[*FSF7GG^Y M%#/W,A+0`#^(R'*U@-X70<&W<#M\^Y%\].:wink:<];P^7%[*LBMY\-]\?X1<4FM M\6JR?(2+G9--S\8GJSG37%[6AY,.;T+>B'\G4$NN6?ZR-?)\\L[?2<1^#*.# MW'OI6+OKM7"TA.%J$9$9-@<[78\O^,2;>9$'??L^\% ",GC<\#3K<:LA;+JM MM,F!WDHN"75A:# %1D+:[?MB`=>(SP&ZL(<];_E;2_FN*;\11:GW`C4=U6RX M'7O9;:*HT 9"*5$HIJAQ.GP%-0/5K#A[[X7*G-A903Q7FPEJ#(1<E% MHNAQ MGHHU, ,_M&VB:EDIF9K5[-K:NVH:,6CNJRY7ZZ :BZ]5R9J7?'7+:NONU*;: M<E&F;"X/U'HEUT8M?#:NBR_3W:JM7W9+[,)&#D!-LPEWL,C)A%CP& 3F00=@ M-G%4XIK$=DG;2=,3M1M44])^D+Q<"]^-^'H4V8UIE9 (1M-10$3+0015H#G# ML3NIAR/M$!S1BCB2TLB5P6B-EN.Q:![X7A2$Y2Q:%_/"4;16WF,1/16+K"(6 MW8?>G,,-Q:=QM^DI:6<;"SOP'4D^-A59%82.Y^.]W\I/<M>Z4C)BK^GRI2"[ M?]?$3;-OO;D7[6=OM2OMJ#E",<17VDWV*X#2A;81V*\"!28@<!\*5T3V%)\4 MR1<'`K92(! 7!P*.NRL0JWY:0(\F*B-=#[I!<BE;4DESML5BJ?7=2O*HD1:! MK8&__/W:D<@$4F/6"_PH#&9;%TPUR9PA+[ _>]AZ'I59;]G%%)"SOCY&C69J M9C.U8[&^FEJGF5JWF5JOF5J_F=J@F=I-$[4G6#\<=PYE/4V<3M6DG>[5H$ON MA\//&H&"ZWJ:5(IV5@WM9C6T6S*TORBROQHOLQCM`-O1:A9YQR9[$=B/[BP> MQZ'3''R?J.C>'&CDV^@&)"_*MB1<)G$1BXV\7>B#[!EY\V4;>0T=7IV"`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`0L(5K4% M!.E.-:7^/C6IPW"V_\_D,5A3LO(O;4S&]C3:MH;S@CV(:#*(:$6^1.<I7Z)@ M%YMC%^YBH\6[V' 3FW+*W6OUU<Y!K9?#J?(7W;P__XIVO-HX%X['R45GY7B! M%%(FNAU_\SF?\B<P%2]I_SVZ,36M2_KC2SJ.D<2Q:!R.]=P2[;"5[?8!8#)_ MT,KVF4JGC&/!35T'LG#/ENW&N_*)RB9>M(EHF8:U?E2R\)>R"7\96JDD-"23 MW @V8B*5,)'I,BCJ-:#8+@*AKC0`(8Q/1&&EC=SZ9&.)- =]%2MQXJQR%*[- MI1;O6JZ(0BOVJS#&Q.)Y^U.:9Q0^!PJWU9X9A8B E>_9"=I*(G94<W%%OQ?X MXCN'KCZ.Q^\28WCV6PD3<3,WR(.7YT9_Z 9!<_SF!L9V;*$`=_.*.#0+HG05 MUW5HQ3-%[;.C]B]&XC:Q-F"S-BUMQ"OUH*-'A_AP6A-TV19CE=F50(@QT-I" MB<;B36548I7.;MR973^.77<B^A:$7\C%()J*T!?180M-E+%VO-"DZ^:5==4F ML=W+RB:WG;OZ2TRLX#RL51%>%4\@2>%%7Y0W]_I/()V.7*Q"B%'NV+G[CIVF MM(U2;\TN].MVRW<4B>,(1+1TTSC,S],DW-0-&3BM8_AYC0*>IDAAR15%HZ<] MN'MFYK^7F=DTRA1K9JJX< FI*O_1S,RV9O1XZ,BW[U'<;/V&?/#L8 HL([>1 M(X&E9NHH=*OWX!-)2ZL?ZS044\Y'I2(@V3G:^6(`R4X%2%;DV@V^]SK)X<\U MX;**H-4)'>5,R(1*#\PFQT/+S@&7'0-F9:> 6=DA8+9S3%<A._=P^XRN4I ; MZ])R7;J;NSY.NU5I/G>_TCU=6JY+);DE9VQI6:9T*I 7:)>=[S71T,AF,%G5 MA=.8S5P&9F^WXH'#`\2PUG9WO":JP!H2;5D+T$.@: &C_1ZX,9Q@7R7::6YJ M%66EQV84!W!1[CBPOX!STQ]UUI.9Y-$6YM+=>DNF0VG(.SYS)FBE@/3KF0X5 M'-$PX@-\R?LZ47U=TZ'\<SO)=(BVP;W(A1!@.F3#)$FK6MO15H(36WAQ`QG3 M`[<J61PDTP!Z]G_%:9!>L.1;-<:MGC<CO:2)T,DB!843H49.N'Z*X+5R5!^\ M1K0Z-])3\Z7GS!?=_96H5X6:^FJO!C4-U&IN.F*I6NIYUZWM6*CI>\O%C -K M_GS7D9+&MH ?=R*8\P?/?BI6C4'MNQ%3H8>/4'X4[V9BNO'Y]K\5H:,6Q*:I MS/>FC7^L41J;9LK9^7XES+%J;#6RE31BO,C_=-/VOB-5US4M=YY.%GC69(%G MC;8U52F/6$].%;%N.]*=2=*M2=0X2LRZ^4]-FO$O3=(&O#78>9OOF;ARXC*8 MPF6G;6CF^)KQ9S7W&=PX>#=^_/KP_P%02P,$% ````@`_%8R*\^]=Y$.`@`` M( @```T```!S;&]G:6YF;RYG;F9OW95=;],P%(;O]RO>W6T24^U\-8K$11DP M%:FHHK";::H\QRFFJ1/%3MCVZSDN7<=*H:BYPU(<6_+SOL?'7Y_U2N'7,E,= M)N);U6"B#=6C9F%/9JH&3\&#+(ZR./;C0E_QX9IA^"3,0D%^57*)0NA2Y3B; MO)N<XP)O23 :QM2Z5B8'YRFC]F4IK$7"ALSW1GG>P#=F^E&!,\9Z6Z8L%5M/ M%N5;SYCQ/9[12\LX8VN?M>_:F ;@)KU%82_JY0)WK2Y=A@^M01 @8(R#15G( MLC#:T4E_UYD*N10^^,H4>H&"@L?-0#DYL _6J=6@_CG@Z6]OMYK<:W+VK)G0 M1_88&^M$66JSP"!7':$-ZJIQ"(?I#LT]%ZR3R3;)_&+$'07A*N3**>DP&8_A M&F&L5+I3S6&%C]4N@Z)J37YZ&'6T!ZO6P=):^?@Y2UZ!9N-04/EW_KO0[FAX M:YZP'N9'PEOSJ(_YD?!SVOOAO>B@G_G?\* ?'O;#HUYXG#R=<2#=X-=7(]2- M7HGF`1E=1!;LGL.?^:(UDCKLL,9[?S3!,;T<#T974^3:UJ5X\"I:*GM8H)9Z MKHVF*W!]RKW0!J9YRC3CR6&-Z6820CJZ+S(*AU$NAO]K!H9[@A!MZ>CAT@9= MFD#2!7Z*,VV<GQ#M"B7N\1KA^<D^J>"%5*>LF#?*NJI1\VXA,KP1.00]<LK: MPY'\:2U^`%!+`P04````" !183(K]8C!'T8```!R````#0```'1R87!L:7-T M+F=N9F]+22U++]'-S$\O2BS(R$PN5M!-R4D!BNGFI>;G)J9G)NL5YROH>AH` MQ0TJ# V2+70,*@P,#,VX4G!I+$LM3DS*S"_&I1$`4$L#!!0````(`/Q6,BN# M</X;,0```#(````*````=6YA;64N9VYF;POTBU"H*B@R-E$PTS/4,U P,C P MU#<PTS<RU34TM3(VM#*Q2$TI4:BP,"M(!I$*7 !02P,$% ````@`^U8R*U U M(1,]" ``IZL```D```!V97-A+F=N9F_MG5MSVC@4Q]_]*?089J<[LGPE;^;6 M[6Q)F-"A[:,")O7$V(PQ3;.??H]\`^S8D "M30X/>4#'1Q=+_Y]T(HE)?VR1 M3][<)QW7GSY*TD1\,78>/!ZN`YM<$_%%_.W$#E:.[Q$"WU)&J73;'Y)Q&#C> M`QF%@?B6FO2:RFPGB40/#/F#,QW:,X<3ING?/O]%5/-?J<N7_-YQG="Q5['? MY".1_*=G=<F3,PM_D+GSRYZ1T"<ZN7?"%5G:`5D&SH('SV3JNWY0?+CK>V'@ MNRY83CY:8+58\M"Y=^VBZ8T?++A+[JRAR-$'YV#I>]+$F=D^&?HS>Z>RE#'I MBQ_"$T-[X4,)1"VT@:@#N=(9T]J,MJ1)IT_&_CQ\XM"F=_9/)VG(N"6UJ+DF MMC?S`W+#%W$.2<,E;9HT][91UK[7Y,;VHP:.;$:!/UM/PUU/&T?MHE'JZ877 MM&,,)7^A:'(G,LJJM?7>A9'\=UST'@]YH;6WBB[U1L,Q&=O!3V<*O8'_Y([+ MQ2N:.$&XA@8>3P/;]EZR2-[ S7IQ#V_X=DXV+VM%YO[:FT%&3)>DZ/5!F7Z) M!B4.]'MXV='K_5#VB9^Q0JC4_3J,NFE6_?:@V'_23_38>+U<^D$(W=7QR#\\ MF(D.4/[,ER_?R>TZ7*Y#,E][4U&P%5EE/NZ?2>?3[;C\^:[H_5'.Y38?`[[\ MX4Q7>\SV#9-MNR<'.N43%/"0!SX[GLT#,@A$Q^NLYW-X8U;V)K]&KHB5:W!H M;*/<Y9T-V@6]"QR0V,'5JE5NGN3AK.!!/N.5I=W8?@V<T-XN8Z=81EKN: Q# MPK4_W,#X*!;WD/QO_/!5Y17VA3+#R_?6+H>OGTE:9I6FJ6/G/WO;V6XJ8"'D M00CC[V%A>R&D6D*HL];(I]*MU$'2F\G(=[S0#JY)%U*O61]0T7D6#3B";C"> M<L^%[I%FSDRAH2KHYS>H^LIWUV$BFYL";FR^E]K(;;!1:>2G^P,ZWPL5-<F5 M*7R4I,O@0=9;TD9B1B[W,C40F8!!2^H(((FZC !2;C&#S?,=[CUNBTG\? (1 M,3;=W0*JY ,9\>DC#+/(MR0<%$J:=,---I\6_ $H`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`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`L%XTBB>T"E-KMRCOK&I`*.(!BKF,5L.+F2Q(O?%#.&LBQ5E MSZ$A0[&$)JMZ7I-/<?$2:G)JAYJ<C8921ZC)K]?DG?U;#1?ENJQ6**BRK.)J MY<)7*_H>,NJ&(*.A1>>&_@=02P$"%@L*"Z8C(K````````````````
M# ```````````" @($`````8W)T=')A<"YG;F9O4$L!A8+% @`^U8R M*T7-03U$4PD``````````0`@`("!*@```&1I<W N9VYF;U!+`0(6 M"Q0(/M6,BN>*UVB+ $``/P&```)``````````$( " @94!D;&QS M+F=N9F]02P$"%@L4````" `4C:\J3+^#%84&``#W,P``"0`````````!`" ` M@('H`0``96YU;2YG;F9O4$L!`A8+% ````@`^U8R*S^QD- _````3@````@` M`````````0`@`("!E @``&9F8BYG;F9O4$L!`A8+% ````@`^U8R*^ 5^PQ' M````50````<``````````0`@`("!^0@``&EO+F=N9F]02P$"%@L4````" #\ M5C(K/N [IRH$``#S,0``"@`````````!`" `@(%E"0``;6]D97,N9VYF;U!+ M`0(6"Q0````(`/M6,BMF@2G>3PH``$=9($`( " @;<-``!P M8VDN9VYF;U!+`0(6"Q0````(`/Q6,BO/O7>1#@(``" (```-$ M( " @2P8``!S;&]G:6YF;RYG;F9O4$L!A8+% @`46$R*_6(P1]&
M<@T``````````0`@`("!91H``'1R87!L:7-T+F=N9F]02P$"%@L4
M" #\5C(K@W#^&S$R"@`````````!" @('6&@=6YA;64N9VYF M;U!+`0(6"Q0````(`/M6,BM0-2$3/0@*>K```)``````````$( " @2\; A``!V97-A+F=N9F]02P4&``````P# "=@``DR,`````
end

Ramin_Assadollahi · September 18, 2001, 11:42am

well, uh, nope!
if i click shutdown, it simply shuts down.
it would be nice to have such a menu, may
it can be configured somehow?

cheers
ram

“ed1k” <ed1k@yahoo.com> schrieb im Newsbeitrag
news:01c14037$49c7e2e0$396fa8c0@ED1K…

Ramin Assadollahi <> assadollahi@exb.de> > wrote in article
9o57pf$2te$> 1@inn.qnx.com> >…
hi ed1k,

well there are no radio buttons, there’s only
the shutdown and the login button

Hi Ramin,
.
If my memory serves me, you could click on shutdown and then should be the
three ways:
Exit to text mode
Reboot computer
Shutdown computer

Cheers,
Eduard.

Ramin_Assadollahi · September 20, 2001, 2:13pm

hi, havent heard anything for days,
any new insights?
ok, ok, i know you have a lot of other
things to do, i’ll shut up!

cheers
ram

“Ramin Assadollahi” <assadollahi@exb.de> schrieb im Newsbeitrag
news:9o7bpl$c8s$1@inn.qnx.com…

thanx a lot,

the script itself did not really work,
i had to remove the 2>/dev/null lines
another problem was, that crttrap did not write
anything to the textfile, just

/usr/photon/bin/devgt-iographics -dldevg-neomagic.so -I0 -d0x10c8,0x0016 -VV

/usr/photon/bin/devgt-iographics -dldevg-vesabios.so -I0 -d0x10c8,0x0016 -VV
and wrote one file, i think it was graphics-modes

the script didn’t compress the .gnfo files, so
i took them to win and zipped them there
u will find this zipfile attached.

i hope, it gives you the information that you need, anyway.
it would be really cool to start using qnx6.1. i’m
really hot to write my first own programs for it.

cheers ramin

Hardware_Support_Acc · September 20, 2001, 6:01pm

Hi Ramin,

It is busy

Did you do a freah install of QNX 6.1 or did you upgrade? Also
the script you used, try running it as root and it should work
properly.

Thanks

Erick.

Ramin Assadollahi <assadollahi@exb.de> wrote:

hi, havent heard anything for days,
any new insights?
ok, ok, i know you have a lot of other
things to do, i’ll shut up! >

cheers
ram

“Ramin Assadollahi” <> assadollahi@exb.de> > schrieb im Newsbeitrag
news:9o7bpl$c8s$> 1@inn.qnx.com> …
thanx a lot,

the script itself did not really work,
i had to remove the 2>/dev/null lines
another problem was, that crttrap did not write
anything to the textfile, just

/usr/photon/bin/devgt-iographics -dldevg-neomagic.so -I0 -d0x10c8,0x0016 -VV

/usr/photon/bin/devgt-iographics -dldevg-vesabios.so -I0 -d0x10c8,0x0016 -VV
and wrote one file, i think it was graphics-modes

the script didn’t compress the .gnfo files, so
i took them to win and zipped them there
u will find this zipfile attached.

i hope, it gives you the information that you need, anyway.
it would be really cool to start using qnx6.1. i’m
really hot to write my first own programs for it.

cheers ramin

Ramin_Assadollahi · September 21, 2001, 9:31am

hi,

i de-installed 6.0 and got the fresh complete 6.1.

indeed, i ran the script as root, for some programs it
didn’t find the path, but more over it had problems with
the '2>/dev/null ', i don’t know why.

i didn’t change the standard bootscript. it’s completely
fresh from the internet.

cheers

ramin

“Hardware Support Account” <hw@qnx.com> schrieb im Newsbeitrag
news:9odat5$1k8$4@nntp.qnx.com…

Hi Ramin,

> It is busy

Did you do a freah install of QNX 6.1 or did you upgrade? Also
the script you used, try running it as root and it should work
properly.

Thanks

Erick.

Ramin Assadollahi <> assadollahi@exb.de> > wrote:
hi, havent heard anything for days,
any new insights?
ok, ok, i know you have a lot of other
things to do, i’ll shut up! >

cheers
ram

“Ramin Assadollahi” <> assadollahi@exb.de> > schrieb im Newsbeitrag
news:9o7bpl$c8s$> 1@inn.qnx.com> …
thanx a lot,

the script itself did not really work,
i had to remove the 2>/dev/null lines
another problem was, that crttrap did not write
anything to the textfile, just

/usr/photon/bin/devgt-iographics -dldevg-neomagic.so -I0 -d0x10c8,0x0016 -VV

/usr/photon/bin/devgt-iographics -dldevg-vesabios.so -I0 -d0x10c8,0x0016 -VV
and wrote one file, i think it was graphics-modes

the script didn’t compress the .gnfo files, so
i took them to win and zipped them there
u will find this zipfile attached.

i hope, it gives you the information that you need, anyway.
it would be really cool to start using qnx6.1. i’m
really hot to write my first own programs for it.

cheers ramin

\